A default Frame Relay WAN is classified as what type of physical network？（）A、point-to-pointB、broadcast multi-accessC、nonbroadcast multi-accessD、nonbroadcast multipoint.broadcast point-to-multipoint
A default Frame Relay WAN is classified as what type of physical network？（）
- A、point-to-point
- B、broadcast multi-access
- C、nonbroadcast multi-access
- D、nonbroadcast multipoint.broadcast point-to-multipoint
相关考题：
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? () A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type
Your network consists of a large hub － and － spoke Frame Relay network with a CIR of 56 kb／s foreach spoke. Which statement about the selection of a dynamic protocol is true?() A. EIGRP would be appropriate if LMI type ANS I is NOT used.B. EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas.C. EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.
In regard to a hub and spoke Frame－Relay data network, what kind of physical network is it classified as?() A. point-to-pointB. broadcast multi-accessC. nonbroadcast multipointD. nonbroadcast multi-accessE. broadcast point-to-multipoint
The following was issues on router TestKingA:TestKingA show ip ospf neighborNeigbor ID PRI State Dead Time Address Interface192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1Which type of OSPF network will provide the output shown in the graphic?（）A. FDDIB. nonbroadcast multiaccessC. broadcast multi-accessD. point-to-point
When configuring Frame Relay using point－to－point subinterfaces, which of the following must not be configured?() A. The local DLCI on each subinterface of the Frame Relay.B. The Frame Relay encapsulation on the physical interface.C. An IP address on the physical interface.D. The subinterface type as point-to-point
Under which circumstance, ie network type, would an OSPF router establish a neighbor adjacency, even though the DR／BDR election process was not performed?() A. Point-to-pointB. Broadcast multicastC. Nonbroadcast multicastD. Backbone area 0E. Virtual Link
You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）A. The Frame Relay encapsulation on the physical interface.B. The local DLCI on each subinterface.C. An IP address on the physical interface.D. The subinterface type as point-to-point.
A default Frame Relay WAN is classified as what type of physical network?() A.point-to-pointB.broadcast multi-accessC.nonbroadcast multi-accessD.nonbroadcast multipoint.broadcast point-to-multipoint
On which types of network will OSPF elect a backup designated router()。 A.point-to-point and multiaccessB.point-to-multipoint and multiaccessC.point-to-point and point-to-multipointD.nonbroadcast and broadcast multipointE.nonbroadcast and broadcast multiaccess
A default Frame Relay WAN is classified as what type of physical network()。 A.point-to-pointB.broadcast multi-accessC.nonbroadcast multi-accessD.nonbroadcast multipointE.broadcast point-to-multipoint
In regard to a hub and spoke Frame-Relay data network, what kind of physical network is it classified as?（）A、point-to-pointB、broadcast multi-accessC、nonbroadcast multipointD、nonbroadcast multi-accessE、broadcast point-to-multipoint
On what kinds of networks does OSPF elect a backup designated router?（）A、Point-to-point and point-to-multipoint networksB、Nonbroadcast and broadcast multipoint multicastingC、Point-to-point and multi-access broadcastingD、Point-to-multipoint and multi-access broadcastingE、Nonbroadcast and broadcast multi-access
Under which network type circumstance would an OSPF router establish router adjacencies while not performing the DR/BDR election process?（）A、Point-to-pointB、BroadcastC、Non-broadcast multi-accessD、Backbone area 0E、None of the above
When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）A、The local DLCI on each subinterface of the Frame Relay.B、The Frame Relay encapsulation on the physical interface.C、An IP address on the physical interface.D、The subinterface type as point-to-point
On which types of network will OSPF elect a backup designated router?（）A、point-to-point and multiaccessB、point-to-multipoint and multiaccessC、point-to-point and point-to-multipointD、nonbroadcast and broadcast multipointE、nonbroadcast and broadcast multiaccess
The following was issues on router TestKingA: TestKingA #show ip ospf neighbor Neigbor ID PRI State Dead Time Address Interface 192.168.1.2 1 Full/- 00:00:37 192.168.1.2 Serial1 Which type of OSPF network will provide the output shown in the graphic?（）A、FDDIB、nonbroadcast multiaccessC、broadcast multi-accessD、point-to-point
Under which circumstance, ie network type, would an OSPF router establish a neighbor adjacency, even though the DR/BDR election process was not performed?（）A、Point-to-pointB、Broadcast multicastC、Nonbroadcast multicastD、Backbone area 0E、Virtual Link
在OSPF路由协议的网络中，OSPF定义了多种网络类型，下面那种网络类型需要选举DR和BDR？（）A、Point-to-pointB、Nonbroadcast（NBMA）C、Point-to-multipointD、Point-to-multipoint nonbroadcast
A default Frame Relay WAN is classified as what type of physical network（）。A、point-to-pointB、broadcast multi-accessC、nonbroadcast multi-accessD、nonbroadcast multipointE、broadcast point-to-multipoint
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）A、frame-relay arpB、frame-relay mapC、frame-relay interface-dlciD、frame-relay lmi-type
A default Frame Relay WAN is classified as what type of physical network?（）A、point-to-point B、broadcast multi-access C、nonbroadcast multi-access D、nonbroadcast multipoint E、broadcast point-to-multipoint
单选题You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）AThe Frame Relay encapsulation on the physical interface.BThe local DLCI on each subinterface.CAn IP address on the physical interface.DThe subinterface type as point-to-point.
单选题A default Frame Relay WAN is classified as what type of physical network?（）Apoint-to-pointBbroadcast multi-accessCnonbroadcast multi-accessDnonbroadcast multipointEbroadcast point-to-multipoint
单选题When configuring Frame Relay using point-to-point subinterfaces, which of the following must not be configured?（）AThe local DLCI on each subinterface of the Frame Relay.BThe Frame Relay encapsulation on the physical interface.CAn IP address on the physical interface.DThe subinterface type as point-to-point
单选题A default Frame Relay WAN is classified as what type of physical network?（）Apoint-to-point Bbroadcast multi-access Cnonbroadcast multi-access Dnonbroadcast multipoint Ebroadcast point-to-multipoint
单选题In regard to a hub and spoke Frame-Relay data network, what kind of physical network is it classified as?（）Apoint-to-pointBbroadcast multi-accessCnonbroadcast multipointDnonbroadcast multi-accessEbroadcast point-to-multipoint
单选题A default Frame Relay WAN is classified as what type of physical network？（）Apoint-to-pointBbroadcast multi-accessCnonbroadcast multi-accessDnonbroadcast multipoint.broadcast point-to-multipoint