A network administrator needs to configure a router for a Frame Relay connection to a non－Cisco router. Which of the following commands will prepare the WAN interface for this connection?() A. Router(config-if)# encapsulation frame-relay q933aB. Router(config-if)# encapsulation frame-relay ansiC. Router(config-if)# encapsulation frame-relay ietfD. Router(config-if)# encapsulation frame-relay islE. None of the above
A network administrator needs to configure a router for a Frame Relay connection to a non－Cisco router. Which of the following commands will prepare the WAN interface for this connection?()
A. Router(config-if)# encapsulation frame-relay q933a
B. Router(config-if)# encapsulation frame-relay ansi
C. Router(config-if)# encapsulation frame-relay ietf
D. Router(config-if)# encapsulation frame-relay isl
E. None of the above
相关考题：
You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?() A. Show interface lmiB. Show frame-relay lmiC. Show interface frame-relayD. Debug frame-relay interface.
Users have been complaining that their Frame Relay connection to the corporate site is very slow. The network administrator suspects that the link is overloaded. Based on the partial output of the Router show frame relay pvc command shown in the graphic, which output value indicates to the local router that traffic sent to the corporate site is experiencing congestion?（）A. DLCI = 100B. last time PVC status changed 00:25:40C. in BECN packets 192D. in FECN packets 147E. in DE packets 0
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit.Which of the following processes are required to accomplish this task?() A. configure static frame relay map entries for each subinterface network.B. remove the ip address from the physical interfaceC. create the virtual interfaces with the interface commandD. configure each subinterface with its own IP addressE. disable split horizon to prevent routing loops between the subinterface networksF. encapsulate the physical interface with multipoint PPP
A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the configuration and issuing the show run command, the password for Telnet access should be encrypted. Which set of commands will accomplish this task?（）A.B.C.D.
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router.How should the network administrator configure the serial interface of the main office router to make the connection?（）A.B.C.D.
Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）A、TestKRouter(config-if)# Encapsulation frame-relay dot1qB、TestKRouter(config-if)# Encapsulation frame-relay aal5snapC、TestKRouter(config-if)# Encapsulation frame-relay ietfD、TestKRouter(config-if)# Encapsulation frame-relay islE、None of the above
A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）A、Router(config-if)# encapsulation frame-relay q933aB、Router(config-if)# encapsulation frame-relay ansiC、Router(config-if)# encapsulation frame-relay ietfD、Router(config-if)# encapsulation frame-relay islE、None of the above
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）A、Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the subinterface BB、Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast trafficC、Configure many sub-interfaces on the same subnetD、Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
A new frame relay connection is being brought up. Which of the following are frame relay LMI type options that can be configured on this new link?（）A、EIA/TIAB、Q.932C、Q.933AD、IEEEE、CiscoF、Annex D
Which WAN connection requires a different interface than the standard interface provided in the Cisco Single-Site Secure Network Foundation deployment design？（）A、Metro EthernetB、DSLC、VPND、CableE、Frame-Relay
Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）A、 Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.B、 This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.C、 The router at RemoteB must be replaced by a Cisco router.D、 Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.E、 There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.
It has become necessary to configure an existing serial interface to accept a second Frame Relay virtualcircuit.Which of the following processes are required to accomplish this task？（）A、configure static frame relay map entries for each subinterface network.B、remove the ip address from the physical interfaceC、create the virtual interfaces with the interface commandD、configure each subinterface with its own IP addressE、disable split horizon to prevent routing loops between the subinterface networksF、encapsulate the physical interface with multipoint PPP
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates?（）A、Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interface.B、Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast traffic.C、Configure many sub-interfaces on the same subnet.D、Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces.
How should a router that is being used in a Frame Relay network be configured to avoid split horizon issues from preventing routing updates？（）A、Configure a separate sub-interface for each PVC with a unique DLCI and subnet assigned to the sub-interfaceB、Configure each Frame Relay circuit as a point-to-point line to support multicast and broadcast trafficC、Configure many sub-interfaces on the same subnetD、Configure a single sub-interface to establish multiple PVC connections to multiple remote router interfaces
A user reports they cannot access the network share folder， the users workstation is configured to use automatic IP. When the administrator checks the IP address the response returns as 169.254.0.5. Which of the following should the administrator verify？（）A、 That there are no DHCP relay serversB、 That the user account on Active Directory is not lockedC、 That the network card driver is not installed incorrectlyD、 The network connection is functioning
A technician temporarily needs an additional network connection in their office to test a newworkstation. Which of the following is the BEST solution to add a temporary network connection?（）A、Install a small network switchB、Use port mirroring on the switchC、Split the pairs of the existing jackD、Install a CSU/DSU
You are a network administrator for your company. The network consists of a single Active Directory domain. All domain controllers and member servers run Windows Server 2003， Enterprise Edition. All client computers run Windows XP Professional. The company has one main office and one branch office. The two offices are connected by a T1 WAN connection. There is a hardware router at each end of the connection. The main office contains 10，000 client computers， and the branch office contains 5，000 client computers. You need to use DHCP to provide IP addresses to the Windows XP Professional computers in both offices. You need to minimize network configuration traffic on the WAN connection. Your solution needs to prevent any component involved in the DHCP architecture from becoming a single point of failure. What should you do？ （）A、 At the main office， configure two Windows Server 2003 computers as a DHCP server cluster. Configure the branch office router as a DHCP relay agent.B、 At the main office， configure two Windows Server 2003 computers as a DHCP server cluster. At the branch office， configure a Windows Server 2003 computer as a DHCP relay agent.C、 At the main office， configure two Windows Server 2003 computers as a DHCP server cluster. At the branch office， configure two Windows Server 2003 computers as a DHCP server cluster.D、 At the main office， configure two Windows Server 2003 computers as DHCP servers. Configure one DHCP server to handle 80 percent of the IP address scope and the other DHCP server to handle 20 percent. Configure the branch office router as a DHCP relay agent.
You install a new hardware router that provides wireless network connectivity between your computer and the Internet. You connect to the router by using a wireless network adapter. Your computer is able to access the Internet but is unable to discover other computers in the local wireless network. You need to configure the wireless connection to allow your computer to discover other computers. What should you do？（）A、Configure the network category of your wireless network connection to Private.B、Configure the network category of your wireless network connection to Public.C、Configure the TCP/IP packet filtering on the wireless network connection.D、Configure the wireless network connection with the appropriate authentication to the router.
单选题Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）ATestKRouter(config-if)# Encapsulation frame-relay dot1qBTestKRouter(config-if)# Encapsulation frame-relay aal5snapCTestKRouter(config-if)# Encapsulation frame-relay ietfDTestKRouter(config-if)# Encapsulation frame-relay islENone of the above
单选题A user reports they cannot access the network share folder， the users workstation is configured to use automatic IP. When the administrator checks the IP address the response returns as 169.254.0.5. Which of the following should the administrator verify？（）A That there are no DHCP relay serversB That the user account on Active Directory is not lockedC That the network card driver is not installed incorrectlyD The network connection is functioning
单选题A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）AMain(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#no shutBMain(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)#no shutCMain(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation frame-relay Main(config-if)#authenication chap Main(config-if)#no shutDMain(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ppp Main(config-if)#no shut
单选题Which WAN connection requires a different interface than the standard interface provided in the Cisco Single-Site Secure Network Foundation deployment design？（）AMetro EthernetBDSLCVPNDCableEFrame-Relay
多选题It has become necessary to configure an existing serial interface to accept a second Frame Relay virtualcircuit.Which of the following processes are required to accomplish this task？（）Aconfigure static frame relay map entries for each subinterface network.Bremove the ip address from the physical interfaceCcreate the virtual interfaces with the interface commandDconfigure each subinterface with its own IP addressEdisable split horizon to prevent routing loops between the subinterface networksFencapsulate the physical interface with multipoint PPP
单选题You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?（）AShow interface lmiBShow frame-relay lmiCShow interface frame-relayDDebug frame-relay interface.
单选题A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）ARouter(config-if)# encapsulation frame-relay q933aBRouter(config-if)# encapsulation frame-relay ansiCRouter(config-if)# encapsulation frame-relay ietfDRouter(config-if)# encapsulation frame-relay islENone of the above
单选题You install a new hardware router that provides wireless network connectivity between your computer and the Internet. You connect to the router by using a wireless network adapter. Your computer is able to access the Internet but is unable to discover other computers in the local wireless network. You need to configure the wireless connection to allow your computer to discover other computers. What should you do？（）AConfigure the network category of your wireless network connection to Private.BConfigure the network category of your wireless network connection to Public.CConfigure the TCP/IP packet filtering on the wireless network connection.DConfigure the wireless network connection with the appropriate authentication to the router.
多选题A new frame relay connection is being brought up. Which of the following are frame relay LMI type options that can be configured on this new link?（）AEIA/TIABQ.932CQ.933ADIEEEECiscoFAnnex D