A cluster node has three network interfaces that support three resource groups with three service IP labels. Each IP label uses IPAT via IP aliasing. One of the adapters fails， and all of the IP labels on it are moved to other interfaces as expected. The system supports the "hot swap" replacement of the network interfaces， and the system engineer has corrected the problem. What will happen to the service IP lab3els when the repaired adapter is noticed by HACMP？（）A、 They will migrate back to the repaired interface.B、 They will not move，the interface will join the pool of available resources.C、 They will not move； the interface will join the cluster as an available non-service adapter. D、 They will migrate to the repaired interface to create an equal number of service IP labels per interface.
A cluster node has three network interfaces that support three resource groups with three service IP labels. Each IP label uses IPAT via IP aliasing. One of the adapters fails， and all of the IP labels on it are moved to other interfaces as expected. The system supports the "hot swap" replacement of the network interfaces， and the system engineer has corrected the problem. What will happen to the service IP lab3els when the repaired adapter is noticed by HACMP？（）
- A、 They will migrate back to the repaired interface.
- B、 They will not move，the interface will join the pool of available resources.
- C、 They will not move； the interface will join the cluster as an available non-service adapter.
- D、 They will migrate to the repaired interface to create an equal number of service IP labels per interface.
相关考题：
You have configured your chassis cluster to include redundancy group 1. Node 0 is configured to be the primary node for this redundancy group. You need to verify that the redundancy group failover is successful.Which command do you use to manually test the failover?（）A. request chassis cluster manual failover group 1 node 1B. request cluster failover redundancy-group 1 node 1C. request chassis cluster manual failover redundancy-group 1 node 1D. request chassis cluster failover redundancy-group 1 node 1
Which command would you use to enable chassis cluster on an SRX device, setting the cluster ID to 1 and node to 0?() A. user@host# set chassis cluster cluster-id 1 node 0 rebootB. user@host set chassis cluster id 1 node 0 rebootC. user@host set chassis cluster cluster-id 1 node 0 rebootD. user@host# set chassis cluster id 1 node 0 reboot
A customer has a resource group rg1 configured on a two node cluster with the following policies：The customer has observed the following scenarios as nodes join the cluster during cluster start up. Scenario 1 Node1 joins cluster as first node - rg1 is acquired by Node1 Node2 joins cluster as second node - rg1 ismoved from Node1 to Node2 Scenario 2 Node2 joins cluster as first node - rg1 is acquired by Node2 Node1 joins cluster as second node - rg1 remainson Node2 Which of the following is the reason for this behavior？（）A、rg1 is configured with a delayed fallback timerB、Settling time policy has not been configured for rg1C、Node1 does not have sufficient resources to support rg1D、Node2 is the first in the ’Default Node Priority’ list for resource group rg1
If both nodes in a chassis cluster initialize at different times, which configuration example will allow you to ensure that the node with the higher priority will become primary for your RGs other than RG0?（）A、[edit chassis cluster] user@host# show redundancy-group 1 { node 0 priority 200; node 1 priority 150;preempt; }B、[edit chassis cluster] user@host# show redundancy-group 1 { node 0 priority 200; node 1 priority 150; monitoring; }C、[edit chassis cluster] user@host# show redundancy-group 1 { node 0 priority 200; node 1 priority 150; control-link-recovery; }D、[edit chassis cluster] user@host# show redundancy-group 1 { node 0 priority 200; node 1 priority 150; strict-priority; }
During a cluster functionality test， and administrator performs a graceful stop for Node ’B’ in a three-node cluster. What is the expected state of the cluster after Node ’B’successfully completes？（） A、 All cluster resources halt on Node ’B’，and one or both surviving nodes will gracefully acquire the resources.B、 All cluster processes halt on Node ’B’，the cluster resources remain active，and the remaining nodes take no action.C、 All cluster processes stay active on Node ’B’，cluster resources are halted，and the remaining nodes take no action.D、 All cluster resources will stop，cluster processes halt on Node ’B’，and the remaining cluster nodes take no action.
A cluster node has a failed fibre adapter requiring the node to be halted to replace it. To minimize downtime， what is the appropriate method of performing this repair？（）A、 Perform the cIRGmove command to move the node’s resources to another cluster node.B、 Perform a graceful stop of the cluster，replace the adapter，and restart the cluster.C、 Perform a force stop of the cluster node，replace the adapter，and restart the cluster. D、 Perform a graceful takeover of the cluster，replace the adapter，and restart the cluster.
A three-node cluster experienced a node failure. The resource groups were acquired as cexpected. The node has been repaired，and HACMP has been restarted. How does the operator determine that the node has successfully re-integrated into the cluster？（） A、 Use the clstat command.B、 Use the cIRGinfor command.C、 Tail the /etc/hacmp.out file and wait for "node_up_complete" to finish successfully.D、 Tail the /usr/es/adm/cluster.log file and wait for "node_up_complete" to finish successfully.
The resource group configuration for a four node cluster is shown below：Which resource groups will be acquired by node N2 if it joins the cluster first？（）A、rgC、rgEB、rgC、rgDC、rgE、rgB、rgDD、rgC、rgD、rgE
A step in the HACMP test plan is to gracefully stop the cluster on a node and to verify that the Shared resources fallover to the standby node. To prepare for this testing step， both nodes in the two-node cluster are in a stable state with the single resource group active on Node ’A’. Which of the following is the best way to execute this portion of the test plan？（） A、 Execute "lssrc -g cluster stop" on Node ’A’B、 Execute "cat /etc//motd /dev/kmem" on Node ’A’C、 Execute "/usr/es/sbin/cluster/utilities/sclstop -gr" on Node ’A’D、 Find the pid of cluster manager daemon on Node ’A’ and issue a "kill-9" against the pid
During a planning session， it is determined that a three node cluster （Node ’A’， Node ’B’， and Node ’C’） will meet the customer’s application needs. Node ’B’ will be a hot-standby fallover node for both Node ’A’ and Node ’C’ resource groups. A serial network for this cluster will require which connections？（） A、 A single serial network between Node ’A’ and Node ’B’ and Node ’C’B、 A point-to-point link between Node ’A’ and Node ’C’，and Node ’B’ and Node ’C’C、 A serial network between Node ’A’ and Node ’C’，and a serial network between Node ’B’ and Node ’C’D、 A point-to-point link between Node ’A’ and Node ’B’ Node ’B’ and Node ’C’ and Node ’A’ ad Node ’C’
An administrator has a two-node PowerHA cluster in a mutual takeover configuration. He needs to updatefrom 5.5 service pack 1 to 5.5 service pack 2. Which of the following actions will perform the updates with norisk of disruption to applications running in the cluster？（）A、Unmanage resource groups on all nodes， update the cluster filesets， start cluster services on all nodes，ensure cluster services stabilizeB、Update the cluster filesets on all nodes. Run ’refresh -s clstrmgrES’ on one node， wait for the cluster tostabilize， repeat for all other nodesC、Unmanage resource groups on one node， update the cluster filesets， start cluster services. Wait for thecluster to stabilize and repeat for all other nodes.D、Bring resource groups （RGs） online on all nodes concurrently， bring RGs offline on one node， update thecluster filesets， bring RGs online， repeat for all other nodes
A customer needs to test the failover capabilities of their cluster. Which of the following AIX commands， whenissued from the command line， will simulate a node crash and cause the cluster resource group running onthat server to fail over to another node？（）A、clstopB、halt -qC、shutdown -FD、stopsrc -s cluster
Which command would you use to enable chassis cluster on an SRX device, setting the cluster ID to 1 and node to 0?（）A、user@host# set chassis cluster cluster-id 1 node 0 rebootB、user@host set chassis cluster id 1 node 0 rebootC、user@host set chassis cluster cluster-id 1 node 0 rebootD、user@host# set chassis cluster id 1 node 0 reboot
Your environment includes a Windows Server 2008 R2 Hyper-V failover cluster. You manage the virtual environment by using Microsoft System Center Virtual Machine Manager （VMM） 2008 R2. You plan to perform maintenance on the Hyper-V failover cluster. You need to complete the maintenance on the failover cluster while maximizing the uptime of the virtual machines （VMs）. What should you do prior to starting maintenance on each cluster node？（）A、Use Failover Cluster Manager to pause the cluster nodeB、Use Failover Cluster Manager to perform a quick migration of all VMs to another cluster nodeC、Use VMM to place the cluster node in maintenance modeD、Use VMM to pause all VMs and move them to another cluster node
You are the network administrator for your company. The network consists of a single Active Directory domain. All computers on the network are members of the domain. You administer a three-node Network Load Balancing cluster. Each cluster node runs Windows Server 2003 and has a single network adapter. The cluster has converged successfully. You notice that the nodes in the cluster run at almost full capacity most of the time. You want to add a fourth node to the cluster. You enable and configure Network Load Balancing on the fourth node. However， the cluster does not converge to a four-node cluster. In the System log on the existing three nodes， you find the exact same TCP/IP error event. The event has the following description： "The system detected an address conflict for IP address 10.50.8.70 with the system having network hardware address 02：BF://0A：32：08：46." In the System log on the new fourth node， you find a similar TCP/error event with the following description： "The system detected an address conflict for IP address 10.50.8.70 with the system having network hardware address 03：BF://0A：32：08：46." Only the hardware address is different in the two descriptions. You verify that IP address 10.50.8.70 is configured as the cluster IP address on all four nodes. You want to configure a four-node Network Load Balancing cluster. What should you do？ （）A、 Configure the fourth node to use multicast mode.B、 Remove 10.50.8.70 from the Network Connections Properties of the fourth node.C、 On the fourth node， run the nlb.exe resume command.D、 On the fourth node， run the wlbs.exe reload command.
You are a network administrator for your company. The network contains four Windows Server 2003 computers configured as a four-node server cluster. Each cluster node is the preferred owner of a clustered instance of Microsoft SQL Server 2000， and each cluster node is configured as a possible owner of all other instances of SQL Server. All nodes have identically configured hardware. All four nodes operate at a sustained 70 percent CPU average. You add a server that has identically configured hardware to the cluster as a fifth node. You want each SQL Server instance to continue operating at the same level of performance in the event of a single node failure. What should you do？ （）A、 Clear the Affect group check box in the cluster resource properties for each SQL Server instance.B、 Configure the fifth node as the only possible owner other than the existing preferred owner of the cluster resources that are associated with each SQL Server instance.C、 Configure the fifth node as the preferred owner of each cluster group that contains an SQL Server instance.D、 Enable failback on each group that contains an SQL Server instance.
You are configuring a failover cluster for a database server. You are assigning four nodes to the cluster. Allnodes have access to a SAN，and adequate storage is available. Which of the following options should youchoose for your quorum configuration？（）A、Node MajorityB、Node And Disk MajorityC、Node And File Share MajorityD、No Majority： Disk Only
Company.com has a two-node HACMP cluster with a single cascading resource group. Node ’A’ is the normal production node， and Node ’B’ is the standby node. One of the first steps in the HACMP test plan is to start the cluster and to verify that al elements for the resource group have been acquired. The administrator who is conducting the HACMP test starts the HACMP daemons on Node ’B’ with the ’smitty clstart" command. The administrator notices that Node ’B’ acquires the elements of the resource group， including a service IP labels，a shared volume group， and an application server that has been started. The expectation was that Node ’B’ would enter the cluster in a standby status， rather than acquiring production resources. What should the administrator do to correct this problem？（） A、 Change the cluster to a rotating design.B、 Change the Cascading without Fallback flag to true.C、 Change the Inactive Takeover field to false in the cluster configuration.D、 Nothing should be done. This is the default behavior for cascading resource groups，and node ’A’ should have been started first.
单选题A node in a three-node cluster was started， ad it acquired the following three cascading resourcegroups： ’rg1’， ’rg12’， and ’rg3’. The cluster design is to have ’rg1’ normally Node ’A’， ’rg2’ normally on Node ’B’， and rg3’ normally on Node ’C’. How can the administrator reposition the resource groups and correct the problem？（）A Change the cluster resource group definitions from cascading to rotating，synchronize the cluster，and restart HACMPB Edit the /urs/es/sbin/utilities/clhosts file to reflect he desired node-to-resource group relationships and restart HACMPC Use the clRGMove utility move rg2 o Node ’B’ and rg3 to Node ’C’，then start the cluster manager on Nodes ’B’ and ’C’ with the clstart utilityD Disable Inactive Node Takeover，check the node priority list in the resource groups definitions，synchronize the cluster，and start HACMP on Nodes ’B’ and ’C’
单选题You have a server that runs Windows Server 2008 Enterprise Edition. The server has the FailoverClustering feature installed. The server has three nodes named NODE1， NODE2， and NODE3. The Microsoft Distributed Transaction Coordinator （MSDTC） resource is installed on the cluster. The cluster hasa dedicated cluster group named Group1 that includes the MSDTC resource. You discover that Group1 isunable to failover to NODE3 from NODE1 or NODE2. The failover from NODE1 to NODE2 functionswithout errors. You need to configure Group1 to support the failover between all cluster nodes. What should you do？（）ARemove the MSDTC resource from Group1BSelect NODE3 as a preferred owner for Group1CRemove NODE3 as a possible owner from all cluster resources in Group1DOnfigure NODE3 as a possible owner for all cluster resources in Group1
单选题An HACMP setting timer may used to allow：（）A The setting or fallback of a cluster custom resource groupB The cluster time to stabilize before starting a custom resource groupC A priority node time to acquire custom resource group at cluster startD A fallover node time to process custom resource states to be monitored
单选题Node ’C’ has just completed reintegration in a three-node cluster. The hacmp.out logifle displays The event node_up_complete for Node ’C’. The cluster administrator wishes to verify that the cluster is stable. In addition to reviewing the cluster log files，what utility should be run to verify the cluster state？（）A clstatB clinfoC cldiagD clverify
单选题A three-node cluster experienced a node failure. The resource groups were acquired as cexpected. The node has been repaired，and HACMP has been restarted. How does the operator determine that the node has successfully re-integrated into the cluster？（）A Use the clstat command.B Use the cIRGinfor command.C Tail the /etc/hacmp.out file and wait for node_up_complete to finish successfully.D Tail the /usr/es/adm/cluster.log file and wait for node_up_complete to finish successfully.
单选题During a cluster functionality test， and administrator performs a graceful stop for Node ’B’ in a three-node cluster. What is the expected state of the cluster after Node ’B’successfully completes？（）A All cluster resources halt on Node ’B’，and one or both surviving nodes will gracefully acquire the resources.B All cluster processes halt on Node ’B’，the cluster resources remain active，and the remaining nodes take no action.C All cluster processes stay active on Node ’B’，cluster resources are halted，and the remaining nodes take no action.D All cluster resources will stop，cluster processes halt on Node ’B’，and the remaining cluster nodes take no action.
单选题Two MAG4610s are running in an active/passive cluster configuration. The system administrator is planning to apply a service package to the cluster.Which process should the administrator follow?（）APerform the upgrade on the active node of the cluster. When completed, the node reboots and then pushes the service package to the passive node automatically.BPerform the upgrade on the passive node of the cluster. When completed, the node reboots and then pushes the service package to the active node automatically.COn the clustering status page, disable the active node. Perform the upgrade on the disabled node. When completed and the node reboots, enable the node on the clustering status page.Repeat the process on the passive node.DOn the clustering status page, disable the passive node. Perform the upgrade on the disabled node. When completed and the node reboots, enable the node on the clustering status page.Repeat the process on the active node.
单选题The en0 interface on Node1 of a two-node cluster has failed. This adapter is configured with a boot addressand under stable operations also has the service address of the cluster’s single resource group. The resourcegroup is configured with the fallback option. The HA network was configured for IPAT via aliasing and now theservice address is on the en1 interface in the cluster. The en0 interface has already been physically replacedand configured with the boot address. Which of the following will return the cluster to its original state andminimize cluster downtime？（）ARun cluster synchronization.BRestart cluster services on Node1.CPerform a swap_adapter using C-SPOCDRestart cluster services on both nodes
单选题Company.com has a two-node HACMP cluster with a single cascading resource group. Node ’A’ is the normal production node， and Node ’B’ is the standby node. One of the first steps in the HACMP test plan is to start the cluster and to verify that al elements for the resource group have been acquired. The administrator who is conducting the HACMP test starts the HACMP daemons on Node ’B’ with the ’smitty clstart" command. The administrator notices that Node ’B’ acquires the elements of the resource group， including a service IP labels，a shared volume group， and an application server that has been started. The expectation was that Node ’B’ would enter the cluster in a standby status， rather than acquiring production resources. What should the administrator do to correct this problem？（）A Change the cluster to a rotating design.B Change the Cascading without Fallback flag to true.C Change the Inactive Takeover field to false in the cluster configuration.D Nothing should be done. This is the default behavior for cascading resource groups，and node ’A’ should have been started first.
单选题A customer has a resource group rg1 configured on a two node cluster with the following policies：The customer has observed the following scenarios as nodes join the cluster during cluster start up. Scenario 1 Node1 joins cluster as first node - rg1 is acquired by Node1 Node2 joins cluster as second node - rg1 ismoved from Node1 to Node2 Scenario 2 Node2 joins cluster as first node - rg1 is acquired by Node2 Node1 joins cluster as second node - rg1 remainson Node2 Which of the following is the reason for this behavior？（）Arg1 is configured with a delayed fallback timerBSettling time policy has not been configured for rg1CNode1 does not have sufficient resources to support rg1DNode2 is the first in the ’Default Node Priority’ list for resource group rg1