单选题The safety valve should be （） in the presence of C/E and Surveyor.Atightened upBsealed upCopened upDunscrewed
单选题
The safety valve should be （） in the presence of C/E and Surveyor.
A
tightened up
B
sealed up
C
opened up
D
unscrewed
参考解析
解析：
暂无解析
相关考题：
What specific jobs do securities outside dressing rooms do?A.In addition to ensuring the life style of the performers, they should prevent any person from entry.B.In addition to ensuring the life safety of the actors, they should stop any reporters from enteringC.In addition to ensuring the life safety of the performers, they should prevent any fans from enteringD.In addition to ensuring the life safety of the performers, they should prevent any unauthorized person from entering
If the head pressure of a reciprocating refrigeration compressor is excessiveA.the relief valve should open before the high pressure cutoutB.the relief valve should open and allow the excess refrigerant to flow to the receiverC.the high pressure cutout switch should operate before the relief valve opensD.you should close the discharging valve
To add refrigerant to the low side of an air conditioning system, the refrigerant should be introduced through the_______ .A.suction service valve as a vaporB.suction service valve as a liquidC.discharge service valve as a vaporD.charging valve as a liquid
A cargo hose is marked with the ______．A.maximum working pressureB.bursting pressureC.safety relief valve settingD.maximum temperature
To ensure proper seating when closing a valve on a tank，the valve should be ______．A.Set up as tight as possible by handB.Set up tight using a valve wrenchC.Closed，opened a half turn，and then closedD.Closed against the stop and the locking pin inserted
Which instrument is suitable for determining the presence of explosive concentrations of fuel oil vapors in tanks ________．A.A flame safety lampB.A combustible gas indicatorC.A liquid cargo meterD.All of the above
As soon as the ship gets alongside the wharf, you should lower the gangway and put a （）below it.A、safety netB、safety beltC、safety lampD、safety device
单选题When operating the air supply system in a covered lifeboat the（）.Afuel supply valve should be closedBhatches，doors，and oar ports should be closedCair cylinder shut-off valve should be closedDengine should be shut off
单选题If a refrigeration system compressor crankcase is sweating, you should （）.Aadd refrigerant to the systemBadjust the thermal expansion valve to the proper settingCadjust the float valve to the proper holding pressureDopen the hand expansion valve
单选题A carburetor is required to have a safety device called a(n)（）.Apressure releaseBbackfire flame arrestorCautomatic shut offDflow valve
单选题If a hydraulic governor has been refilled with oil, the engine should be operated until it reaches normal temperaturethen the air should be purged, and the（）Arack position should be adjustedBcompensating needle valve should be opened fully compensatingCneedle valve should be adjusted to stabilize operationDspeed limiting device should be adjusted
单选题In readying an auxiliary water-tube boiler for a routine hydrostatic test, which of the following procedures should be undertaken prior to filling the boiler with fresh water?（）AThe safety valve escape piping should be disconnected from the valve body and a blank insertedBThe boiler vent valves should be openedCAll hand-hole/manhole covers should be tightened up as much as possible to preclude any leaksDAll of the above
单选题In readying an auxiliary water-tube boiler for a routine hydrostatic test, which of the following procedures should be undertaken prior to filling the boiler with fresh water?（）AThe safety valve escape piping should be disconnected from the valve body and a blank insertedBThe boiler vent valves should be openedCAll handhole/manhole covers should be tightened up as much as possible to preclude any leaksDAll of the above
单选题If the head pressure of a reciprocating refrigeration compressor is excessive, （）.Athe relief valve should open before the high pressure cutoutBthe relief valve should open and allow the excess refrigerant to flow to the receiverCthe high pressure cutout switch should operate before the relief valve opensDyou should close in on the suction valve
单选题If the head pressure is too high,（）Athe relief valve should open before the high-pressure cutoutBthe relief valve should open and let excess refrigerant go to receiverCthe high-pressure cutout switch should operate before the relief valve opensDclose in on the suction valve
单选题Which of the listed statements is correct concerning the starting of centrifugal pumps?（）AThey should always be started with the discharge valve closedBThey should always be started with the discharge valve openedCA priming pump is always required to flood the impeller suctionDThey should always be started with the sealing line valves closed
单选题After fuel tanks have been topped off, which of the listed procedures should be followed next?（）AThe pressure-vacuum relief valve should be resetBThe tanks should be made seaworthy to prevent contaminationCThe tanks should be sounded to make sure the levels are not risingDThe tanks should be marked with a bull stamp on the manifold filling valve
单选题To add refrigerant to the low side of an air conditioning system, the refrigerant should be introduced through the （）Asuction service valve as a vaporBsuction service valve as a liquidCdischarge service valve as a vaporDcharging valve as a liquid
单选题To add refrigerant to the high side of an air conditioning system, you should introduce the refrigerant through the （）.Adischarge service valve as a vaporBsuction service valve as a liquidCcharging valve as a liquidDcondenser purge valve as a vapor
单选题（） supplies pilot air to control the cylinder air start valves.AAn air compressorBAn indicator cockCAn air distributorDA safety valve
单选题What safety precautions should be observed by the crew while working around machinery in an engine room?（）AThey should wear safety shoesBThey should wear ear protectionCThey should not wear jewelryDAll of the above
单选题In some type of two-stroke engines, besides some small holes for（）, starting valve, safety valve, indicator cock, and central opening in each cylinder cover for mounting the（）Afuel valves；exhaust valveBexhaust valves；inlet valveCfuel valves；inlet valveDexhaust valves；fuel valve
单选题During the dock repair, each sea valve must be disassembled, cleaned and ground well.Before it reassemble the sealing surface between the valve and the valve seat should be checked by （）Achief engineerBsurveyorCthe engineerDthe technique personnel of the shipyard