单选题What does the number one 1 represent for interface fe-0/0/1？（）Aport numberBPCI slot numberCchannel numberDvirtual PIC number
单选题
What does the number one 1 represent for interface fe-0/0/1？（）
A
port number
B
PCI slot number
C
channel number
D
virtual PIC number
参考解析
解析：
暂无解析
相关考题：
In the exhibit, what does the () symbol indicate?() A. There is a software issue with ge-1/0/1.0 interface.B. There is a hardware issue with ge-1/0/1.0 interface.C. The next hop of 172.25.213.11 is selected.D. The next hop of 172.25.213.11 is not resolvable.
What is the maximum number of output policy lists that you can attach to an IP interface?() A.1B.2C.128D.512
For the interface ge－1／2／3.4, what does the "ge" represent?() A. Gigabit EthernetB. SONET/SDHC. Aggregated EthernetD. GRE
How do you enable interface fe－0／0／0 under the [edit protocols isis] level to form both a Level 1 and Level 2 adjacency?() A. set interface fe-0/0/0.0B. set interface fe-0/0/0.0 all levelC. set interface fe-0/0/0.0 level 3 enableD. set interface fe-0/0/0.0 level 1 level 2
After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"() A.Layer 1 on the interface is up but Layer 2 is down.B.Layer 2 on the interface is up but Layer 3 has not been configured.C.The interface is administratively up but the link status is down.D.The interface is up but has been administratively turned off.
Router R1 has been conf igured with an ipv6 route 2000::／64 S0／0／0 64 command.Which of the following does the 64 at the end of the command represent?() A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?() A.the port-channel 1 interfaceB.the highest number member interfaceC.all member interfacesD.the lowest number member interface
Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。A、The Mac address of the NIC in Sever1B、The IP address of Server 1.C、The MAC address of the s0/0/0 interface of router R2D、The IP address of the s0/0/0 interface of router R1E、The IP address of the Fa0/0 interface of router R1
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）A、MetricB、Administrative distanceC、Timeout (seconds)D、Prefix lengthE、Interface ID
When troubleshooting a network， the output of the command show interfaces indicates a large number of runts. What is a runt？（）A、the number of packets that are discarded because they exceed the maximum packet size of the mediumB、errors created when the CRC generated by the originating LAN station or far-end device does not match the checksum calculated from the data received.C、the number of packets that are discarded because they are smaller than the minimum packet size of the mediumD、the number of received packets that were ignored by the interface because the interface hardware ran low on internal buffersE、the number of times that the interface requested another interface within the router to slow down
A standard access control list has been configured on a router and applied to interface Serial 0 in anoutbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen whentraffic being filtered by the access list does not match the configured ACL statements for Serial 0？（）A、The traffic is droppedB、The resulting action is determined by the destination IP addressC、The source IP address is checked，and，if a match is not found， traffic is routed out interface Serial 1D、The resulting action is determined by the destination IP address and port number
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?（）A、the port-channel 1 interfaceB、the highest number member interfaceC、all member interfacesD、the lowest number member interface
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A、The Popcorn router is not forwarding RIP updates.B、The Popcorn router did not include network 192.168.12.0 in its routing configuration.C、The Ethernet1 interface of the Popcorn router is shutdown.D、The clockrate is not present in the configuration of one of the routers.E、The Serial interface of the Popcorn router is not operating.
What is shown by the command show interfaces extensive fe-0/0/0 but not shown by the command show interface detail fe-0/0/0？（）A、input error counterB、interface MTU sizeC、input packets counterD、the IP address on logical interface fe-0/0/0.0
多选题You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）Aset protocols isis inet6Bset routing-options router-id router-idCset protocols ospf3 area 0 interface allDset interface fe-0/0/1 unit 0 family inet6Eset routing-options ipv6-router-id router-id
单选题How do you enable interface fe-0/0/0 under the [edit protocols isis] level to form both a Level 1 and Level 2 adjacency?（）Aset interface fe-0/0/0.0Bset interface fe-0/0/0.0 all levelCset interface fe-0/0/0.0 level 3 enableDset interface fe-0/0/0.0 level 1 level 2
单选题After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"（）ALayer 1 on the interface is up but Layer 2 is down.BLayer 2 on the interface is up but Layer 3 has not been configured.CThe interface is administratively up but the link status is down.DThe interface is up but has been administratively turned off.
单选题What is shown by the command show interfaces extensive fe-0/0/0 but not shown by the command show interface detail fe-0/0/0？（）Ainput error counterBinterface MTU sizeCinput packets counterDthe IP address on logical interface fe-0/0/0.0
单选题When the average of a list of course grades is multiplied by the number of courses, the result is n. What does n represent?AHalf the number of coursesBHalf the sum of course gradesCThe number of coursesDThe average of the course gradesEThe sum of the course grades
单选题A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?（）Athe port-channel 1 interfaceBthe highest number member interfaceCall member interfacesDthe lowest number member interface
多选题Which two are correct when configuring an IP address for a Fast Ethernet interface?（）Aset interfaces fe-0/0/0 address 10.1.1.1/24Bset interfaces fe-0/0/0.0 family inet address 10.1.1.1/24Cset interfaces fe-0/0/0.0 address 10.1.1.1/24Dset interfaces fe-0/0/0 unit 0 family inet address 10.1.1.1/24
单选题Which command is a valid way to view the status of an interface？（）Ashow interfaces fe-0/0/0 extensiveBshow interfaces fe-0/0/0 statusCshow interfaces fe-0/0/0 health-infoDshow interfaces fe-0/0/0 verbose
单选题For the interface ge-1/2/3.4, what does "ge" represent?（）ASONET/SDHBGigabit EthernetCAggregated EthernetDGRE
单选题Which option is correct to configure the maximum transmit packet size of a Fast Ethernet interface?（）Aset interfaces fe-0/0/0 unit 0 ethernet-options mtu 1200Bset interfaces fe-0/0/0 mtu 1200Cset interfaces fe-0/0/0 unit 0 mtu 1200Dset interfaces fe-0/0/0.0 mtu 1200
单选题A standard access control list has been configured on a router and applied to interface Serial 0 in anoutbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen whentraffic being filtered by the access list does not match the configured ACL statements for Serial 0？（）AThe traffic is droppedBThe resulting action is determined by the destination IP addressCThe source IP address is checked，and，if a match is not found， traffic is routed out interface Serial 1DThe resulting action is determined by the destination IP address and port number
单选题When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?（）Aping atm vci 0.100 interface at-0/1/0 end-to-endBping atm vci 0.100 interface at-0/1/0 circuitCping atm vci 0.100 interface at-0/1/0 far-endDping atm vci 0.100 interface at-0/1/0 final-hop