单选题The position of the interface between oil and water within the centrifuge is achieved by the use of ().Agravity discBcentrifugal bowlCa stack of discsDmain sealing ring

单选题
The position of the interface between oil and water within the centrifuge is achieved by the use of ().
A

gravity disc

B

centrifugal bowl

C

a stack of discs

D

main sealing ring


参考解析

解析: 暂无解析

相关考题:

He () oil and water, but they (). A、mixed, don’t mixB、mixxed, were not mixxedC、mixed, were not mixingD、mixxed, don’t mix

A high rate of separation between oil and water is favored by ______.A.large size of oil globule(小球)B.low temperatureC.high viscosityD.high flow rate

The height of tide is the ______.A.depth of water at a specific time due to tidal effectB.difference between the depth of the water and the area's tidal datumC.difference between the depth of the water and the high water tidal levelD.difference between the depth of the water at high tide and the depth of the water at low tide

OIL-IN-WATER are ______.A.sediment of oil in waterB.oil dissolvents in waterC.solid oil aggregatesD.droplets of oil suspended in water

()extinguish oil and electrical fires with water.A、DoB、DidC、NeverD、Isn’t

单选题A high rate of separation between oil and water is favored by ().Alarge size of oil globuleBlow temperatureChigh viscosityDhigh flow rate

单选题You should frequently compare drum-mounted and remote-reading water level indicators() between these have contributed to failures because of overheating through shortage of water, when a boiler was being oil-fired.AdescriptionsBdiscrepanciesCdifferentDdeflections

单选题If the cooling water temperature and the lube oil temperature in a diesel engine are too high, the cause can be ()Aa dirty lube oil strainerBinternal water leaksCan oil suction line restrictionDexcessive wears of the cooling water pump

单选题Factor influencing the position of the interface between the liquid seal and the oil in a purifier is ().AthroughputBback pressureCgravity discDNone of the above is wrong

单选题Which of the conditions listed may occur in an operating diesel engine if air pockets form within the cylinder head circulating water passages? ()AHydraulic stress and distortion will developBHot spots will developCFuel oil viscosity will increasedDAn increase in trapped deposits of scale and dirt

单选题The height of tide is the ().Adepth of water at a specific time due to tidal effectBdifference between the depth of the water and the area's tidal datumCdifference between the depth of the water and the high water tidal levelDdifference between the depth of the water at high tide and the depth of the water at low tide

单选题The interface between the liquid seal (water) and the oil should be positioned () possible to the bowl periphery.Aas far asBas soon asCas close asDas closer as

单选题Which of the following conditions indicates the dilution of diesel engine lube oil by fuel oil?()AWater discharging from the water outlet of the lube oil purifierBFuel oil discharging from the water outlet of the lube oil purifierCLube oil discharging from the water outlet of the lube oil purifierDA change in the lube oil viscosity

单选题An oil water monitor is required in order to measure ().Athe oil content in waterBthe water content in fuel oilCthe water level in bilge wellDthe oil level in bilge well

单选题The remaining oil/water mixture now flows down into the fine separating compartment and moves slowly between the() in the Turbulo separator.Acatch platesBswash platesCcover platesDbedplates

单选题Which of the following statements is true concerning an oil cooler?()AThe oil temperature is less than the cooling water temperatureBThe oil pressure is less than the cooling water pressureCThe oil pressure is greater than the cooling water pressureDThe oil flow control valve is always installed in the oil input line

单选题The principle of separation by which all commercially available oily water separators function is () differential between oil and water.Athe temperatureBthe viscosityCthe gravityDthe size

单选题For a L√Opurifier, if the back pressure of the oil outlet is too high, the interface between oil and water in the bowl will ().Abe interruptedBmove downwardsCmove outwardsDretain original position

单选题Which of the following influences the position of the interface between the liquid seal and the oil in a purifier?()AHeight of the machineBTemperature of the liquid sealCGravity discDBowl diameter

单选题The tailshaft sealing arrangement found a little lube oil leaky and caused a lot of seawater into the bearing, the step should be taken as a makeshift is()Adropping lube oil for lubrication, reducing the pollution to the seaBsetting a temporary gravity oil tank and enhanced the position properlyClubricating with the used lube oilDlubricating with the fresh water and navigation in a lower speed

单选题Oil water separators are used to ensure that ships don’t discharge oil when () bilge water.Ato pump offBbeing pumpedCpumping outDit pumping out

单选题()are used to ensure that ships don’t discharge oil when pumping out oily water from any oil contaminated space.ABoilerBIncineratorCOily water separatorDSewage treatment unit

单选题The function of lubricating oil is to ()Amaintain even distribution of bearing wearBmaintain a constant oil temperatureCmaintain a pressurized film between moving surfacesDremove entrained water

单选题In the process of the shafting management, special attention should be paid to()Aon the sailing, the water in the aft peak tank should be excluded as much as possibleBthe stuffing style ahead sealing shouldn’t have any water leaking outCSimplex astern sealing shouldn’t have any oil leaking outDSimplex ahead sealing can have some oil leaking out

单选题Coalescence is the breakdown of surface tension between oil droplets in an oil/water mixture, which causes them to join and () in size.AexpandBextractCincreaseDdecrease

单选题In a purifier, the interface between the liquid seal and the oil should be positioned as close as possible to ().Athe outlet of oilBthe outlet of waterCthe bowl peripheryDthe center of bowl

单选题Before the sludge in a purifier is ejected,()Athe oil feeding is stopped and replaced by admitting flushing waterBthe flushing water feeding is stopped and replaced by admitting oilCthe feeding of dirty oil and flushing water is stoppedDthe feeding of dirty oil and flushing water is admitted