单选题A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）AThe new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.BThe configuration revision of the new switch was higher than the configuration revision of the production VTP domain.CThe link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.DThe ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
单选题
A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）
A
The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.
B
The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.
C
The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.
D
The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
参考解析
解析：
暂无解析
相关考题：
A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch.Which of the following settings on the switch will need to be configured to support the printer?（）A. MAC filteringB. IP addressC. PoED. Port speed
A company is experiencing network delays. The network administrator discovers that a worker in a location far from the MDF has connected an old 10BASE-T switch with redundant links to the existing network.How could this action be responsible for the impaired network performance?（）A. Connecting a host to the old switch has created a broadcast storm.B. The 10BASE-T switch forced the entire network to be reduced to 10 Mbps operation.C. The old switch does not support VLANs, which has disabled the VLAN configuration of the entire the network.D. The old switch does not support full-duplex operation, effectively forcing half-duplex operation throughout the network.E. Spanning Tree Protocol has elected the old switch as the root bridge, creating inefficient data paths through the switched network.
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port（）。A、This is a 10 Mb/s switch portB、This is a 100 Mb/s switch portC、This is an Ethernet port operating at half duplexD、This is an Ethernet port operating at full duplexE、This is a port on a network interface card in a PC
Which term describes a spanning-tree network that has all switch ports in either the blocking or forwardingstate？ （）A、redundantB、spannedC、provisionedD、converged
Which statement correctly describes network security settings in Cisco Network Assistant for the Catalyst Express 500 Switch？（）A、The LOW setting enables broadcast storm control， but has no effect on the number of devices that can connect to a switch portB、The LOW setting enables broadcast storm control and limits the number of devices that can connect to a switch port.C、The LOW setting disables broadcast storm control but limits the number of devices that can connect to a switch portD、The default network setting is "HIGH"
A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）A、The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.B、The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C、The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.D、The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network. Which three issues on Switch2 could be the cause？（）A、Switch2 is configured for only VLAN1B、Switch2 is a VTP server in a different domainC、Switch2 is a VTP server in the Company domainD、Switch2 is not a VTP domain.E、Switch2 has a lower VTP configuration revision number than the current VTP revisionF、Switch2 has a higher VTP configuration revision number than the current VTP revision
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？ （）A、Verify that different native VLANs exist between two switches for security purposes.B、Verify that the VLAN was added on all switches with the use of the show vlan command. C、Verify that the switch is configured to allow for trunking on the switch ports.D、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network?（）A、One router is running RIPv1.B、RIP neighbor is 224.0.0.9.C、The network contains a loop.D、Network 10.10.1.0 is reachable.
A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。A、Establish a direct link from the switch to all other switches in the network.B、Assign the switch a higher MAC address than the other switches in the network have.C、Configure the switch so that it has a lower priority than other switches in the network.D、Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.E、Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?（）A、Lower the bridge priority number.B、Change the MAC address of the switch.C、Increase the VTP revision number for the domain.D、Lower the root path cost on the switch ports.E、Assign the switch an IP address with the lowest value.
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）A、The wrong cable type has been used.B、. IDS has shut down the computer's switch port.C、The port on the switch is configured incorrectlyD、Spanning tree protocol was implemented.
单选题The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?（）ALower the bridge priority number.BChange the MAC address of the switch.CIncrease the VTP revision number for the domain.DLower the root path cost on the switch ports.EAssign the switch an IP address with the lowest value.
单选题The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network?（）AOne router is running RIPv1.BRIP neighbor is 224.0.0.9.CThe network contains a loop.DNetwork 10.10.1.0 is reachable.
单选题A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）AThe new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.BThe configuration revision of the new switch was higher than the configuration revision of the production VTP domain.CThe link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.DThe ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
单选题A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）AoneBthreeCtwoDzero
单选题A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge?（）AEstablish a direct link from the switch to all other switches in the network.BAssign the switch a higher MAC address than the other switches in the network have.CConfigure the switch so that it has a lower priority than other switches in the network.DConfigure the switch for full-duplex operation and configure the other switches for half-duplex operation.EConnect the switch directly to the MDF router， which will force the switch to assume the role of root bridge.
单选题The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network？（）A Lower the bridge priority number.B Change the MAC address of the switch.C Increase the VTP revision number for the domain.D Lower the root path cost on the switch ports.E Assign the switch an IP address with the lowest value.
多选题A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network. Which three issues on Switch2 could be the cause？（）ASwitch2 is configured for only VLAN1BSwitch2 is a VTP server in a different domainCSwitch2 is a VTP server in the Company domainDSwitch2 is not a VTP domain.ESwitch2 has a lower VTP configuration revision number than the current VTP revisionFSwitch2 has a higher VTP configuration revision number than the current VTP revision
单选题A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch. Which of the following settings on the switch will need to be configured to support the printer?（）AMAC filteringBIP addressCPoEDPort speed
单选题A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）AThe wrong cable type has been used.B. IDS has shut down the computer's switch port.CThe port on the switch is configured incorrectlyDSpanning tree protocol was implemented.
单选题You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？ （）AVerify that different native VLANs exist between two switches for security purposes.BVerify that the VLAN was added on all switches with the use of the show vlan command. CVerify that the switch is configured to allow for trunking on the switch ports.DVerify that each switch port has the correct IP address space assigned to it for the new VLAN.
单选题Which statement correctly describes network security settings in Cisco Network Assistant for the Catalyst Express 500 Switch？（）AThe LOW setting enables broadcast storm control， but has no effect on the number of devices that can connect to a switch portBThe LOW setting enables broadcast storm control and limits the number of devices that can connect to a switch port.CThe LOW setting disables broadcast storm control but limits the number of devices that can connect to a switch portDThe default network setting is HIGH
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router
单选题A company is experiencing network delays. The network administrator discovers that a worker in a location far from the MDF has connected an old 10BASE-T switch with redundant links to the existing network. How could this action be responsible for the impaired network performance?（）AConnecting a host to the old switch has created a broadcast storm.BThe 10BASE-T switch forced the entire network to be reduced to 10 Mbps operation.CThe old switch does not support VLANs, which has disabled the VLAN configuration of the entire the network.DThe old switch does not support full-duplex operation, effectively forcing half-duplex operation throughout the network.ESpanning Tree Protocol has elected the old switch as the root bridge, creating inefficient data paths through the switched network.
单选题A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port（）。AThis is a 10 Mb/s switch portBThis is a 100 Mb/s switch portCThis is an Ethernet port operating at half duplexDThis is an Ethernet port operating at full duplexEThis is a port on a network interface card in a PC