A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port（）。A、This is a 10 Mb/s switch portB、This is a 100 Mb/s switch portC、This is an Ethernet port operating at half duplexD、This is an Ethernet port operating at full duplexE、This is a port on a network interface card in a PC
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port（）。
- A、This is a 10 Mb/s switch port
- B、This is a 100 Mb/s switch port
- C、This is an Ethernet port operating at half duplex
- D、This is an Ethernet port operating at full duplex
- E、This is a port on a network interface card in a PC
相关考题：
While troubleshooting an issue in the Ezonexam LAN you notice that a network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?A. This is an Ethernet port operating at half duplexB. This is an Ethernet port operating at full duplexC. This is a port on a network interface card in a PCD. This is 10 MB/s switch portE. This is a 100 MB/s switch portF. None of the above
Which two commands correctly verify whether port security has been configured on port FastEthernet 0／12 on a switch?() A. SW1#show swithport port-security interface FastEthernet 0/12B. SW1# show swithport port-secure interface FastEthernet 0/12C. SW1# show port-secure interface FastEthernet 0/12D. SW1#show running-configE. SW1#show port-security interface FastEthernet 0/12
Users on the 172.17.22.0 network cannot reach the server located on the 172.31.5.0 network.The network administrator connected to console port,issued the show ip route command,and was able to ping the server.Based on the output of the show ip route command topology shown in the graphic,what is the cause of the failure?（）A.IP routing is not enabledB.A static route is configured incorrectlyC.The network has not fully convergedD.The FastEthernet interface on Coffee is disabledE.The routing table on Coffee has not updatedF.The neighbor relationship table is not correctly updated
Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0／10 is not the root port for VLAN 2?() A.This switch has more than one interface connected to the root network segment in VLAN 2.B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.C.This switch interface has a higher path cost to the root bridge than another in the topology.D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.
Which two commands correctly verify whether port security has been configured on port FastEthernet0/12 on a switch？（）A、SW1#shows withport port-security interface FastEthernet0/12B、SW1#shows withport port-secure interface FastEthernet0/12C、SW1#show port-secure interface FastEthernet0/12D、SW1#show running-config
Which two of these are characteristics of an IDS sensor？（）A、passively listens to network trafficB、is an active device in the traffic pathC、has a permissive interface that is used to monitor networksD、traffic arrives on one IDS interface and exits on anotherE、has a promiscuous interface that is used to monitor the network
A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?（）A、This is a 10 Mb/s switch port.B、This is a 100 Mb/s switch port.C、This is an Ethernet port operating at half duplex.D、This is an Ethernet port operating at full duplex.E、This is a port on a network interface card in a PC
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System？（）A、 An interface ’san-port-channel’ in NXOSB、 An interface ’port-channel’ in NXOSC、 An interface ’port-channel’ with ’mode fc’ configuredD、 An interface ’fc-port-channel’ in NXOS
Which two commands correctly verify whether port security has been configured on portFastEthernet 0/12on a switch？（）A、SW1#show swithport port-security interface FastEthernet 0/12B、SW1# show swithport port-secure interface FastEthernet 0/12C、SW1# show port-secure interface FastEthernet 0/12D、SW1#show running-config
Company.com with a newly installed cluster has been checking the logfiles to determine if the cluster has had any recent activity. The non-IP RS232 heartbeat connection seems to be having a difficulty. The serial network goes down，and then a couple of minutes later comes back up again. This pattern is repeated many times in the log. If this system was installed without regard to best practices， what is the most likely problem with the serial network？（） A、 The serial port is malfunctioning and needs to be repaired.B、 The baud rate is incorrectly specified in the AIX devices configuration.C、 The serial port is not a port approved to support HACMP heartbeat traffic.D、 The baud rate is incorrectly specified in the HACMP interface configuration.
Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch？（）A、SW1#show swithport port-security interface FastEthernet 0/12B、SW1# show swithport port-secure interface FastEthernet 0/12C、SW1# show port-secure interface FastEthernet 0/12D、SW1#show running-configE、SW1#show port-security interface FastEthernet 0/12
Cisco IDS sensors form the eyes and ears of your Cisco network intrusion detection system. Placing sensors correctly throughout your network is crucial to successfully implementing your Cisco intrusion detection system .Which two of these are characteristics of an IDS sensor？（）A、 has a permissive interface that is used to monitor networksB、 is an active device in the traffic pathC、 passively listens to network trafficD、 has a promiscuous interface that is used to monitor the network
Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch?（）A、SW1#show swithport port-security interface FastEthernet 0/12B、SW1# show swithport port-secure interface FastEthernet 0/12C、SW1# show port-secure interface FastEthernet 0/12D、SW1#show running-config
Refer to the exhibit. A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands.Which two of these changes are necessary for SwitchA to meet the requirements? （）A、Port security needs to be globally enabled.B、Port security needs to be enabled on the interface.C、Port security needs to be configured to shut down the interface in the event of a violation.D、Port security needs to be configured to allow only one learned MAC address.E、Port security interface counters need to be cleared before using the show command.F、The port security configuration needs to be saved to NVRAM before it can become active.
A user’s workstation currently has four connected IDE devices. Which of the following could be added to the workstation to allow more ATA devices to be added to the workstation?（）A、Network Interface cardB、Port expansion cardC、Serial interface cardD、Modem card
Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement：（） A、 A single adapter network using the Network Interface Card in each nodeB、 A single adapter network using persistent addresses on the Network Interface Card in each nodeC、 A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.D、 EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover
An AIX server has 2 network interfaces and the system administrator wants to enable the users on the locally configured network interface to be able to connect to systems configured on the global network interface. How is it accomplished？（）A、Enable routed on the serverB、Enable gated on the serverC、Enable ipforwarding on the serverD、Set network options back to default
Your network contains a server named Server1 that has the Routing role service installed. Server1 has two network connections. One network connection connects to the internal network. The other network connection connects to the Internet.All network connections connected to the internal network use private IP addresses. You install a Web server named Web1. Web1 hosts a secured Web site that only allows connections over TCP port 8281. Web1 is connected to the internal network.You need to ensure that the secure Web site can be accessed from the Internet.What should you do from the Routing and Remote Access console？（）A、Configure Routing Information Protocol (RIP), and then activate authentication on the RIP interface.B、Configure Routing Information Protocol (RIP), and then configure the incoming packet protocol settings on the RIP interface.C、Configure Network Address Translation (NAT), and then add a new service to the NAT interface.D、Configure Network Address Translation (NAT), and then enable the Secure Web Server (HTTPS) service on the NAT interface.
单选题Company.com with a newly installed cluster has been checking the logfiles to determine if the cluster has had any recent activity. The non-IP RS232 heartbeat connection seems to be having a difficulty. The serial network goes down，and then a couple of minutes later comes back up again. This pattern is repeated many times in the log. If this system was installed without regard to best practices， what is the most likely problem with the serial network？（）A The serial port is malfunctioning and needs to be repaired.B The baud rate is incorrectly specified in the AIX devices configuration.C The serial port is not a port approved to support HACMP heartbeat traffic.D The baud rate is incorrectly specified in the HACMP interface configuration.
单选题Company.com has I/O slot constraints on two nodes that are going to be configured in an HACMP cluster. There is room for only one Network Interface Card in each node，in addition to the built-in Ethernet port on the system planer. The best HACMP configuration for these servers is to implement：（）A A single adapter network using the Network Interface Card in each nodeB A single adapter network using persistent addresses on the Network Interface Card in each nodeC A dual adapter network using the internal Ethernet adapters as an non-service interface with IPAT via IP Replacement.D EtherChannel high availability for the network connections with HACMP cascading resource groups for data and application fallover
多选题Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch?（）ASW1#show swithport port-security interface FastEthernet 0/12BSW1#show swithport port-secure interface FastEthernet 0/12CSW1#show port-secure interface FastEthernet 0/12DSW1#show running-config
多选题Which two commands correctly verify whether port security has been configured on portFastEthernet 0/12on a switch？（）ASW1#show swithport port-security interface FastEthernet 0/12BSW1# show swithport port-secure interface FastEthernet 0/12CSW1# show port-secure interface FastEthernet 0/12DSW1#show running-config
多选题Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch？（）ASW1#show swithport port-security interface FastEthernet 0/12BSW1# show swithport port-secure interface FastEthernet 0/12CSW1# show port-secure interface FastEthernet 0/12DSW1#show running-configESW1#show port-security interface FastEthernet 0/12
单选题A user has no network connectivity. A check of the associated port indicates that the interface is up，the line protocol is down. Which item would most likely cause this problem？（）ASpeed mismatchBIncorrect encapsulationCMTU set too lowDDuplex mismatch
单选题A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?（）AThis is a 10 Mb/s switch port.BThis is a 100 Mb/s switch port.CThis is an Ethernet port operating at half duplex.DThis is an Ethernet port operating at full duplex.EThis is a port on a network interface card in a PC
单选题Assume that network-based application recognition （NBAR） has been configured to gather traffic for all known protocols on an interface. Which command will display the statistical results of all recognized protocols？（）Ashowip nbarBshowip nbar pdimCshow ip nbar port-mapDshow ip nbar protocol-discovery
单选题A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port（）。AThis is a 10 Mb/s switch portBThis is a 100 Mb/s switch portCThis is an Ethernet port operating at half duplexDThis is an Ethernet port operating at full duplexEThis is a port on a network interface card in a PC