单选题A blinking green power LED indicates which of the following conditions on a Cisco Series 1000 lightweight access point？（）Alost connection to the controllerBduplicate IP addressCstartupDsite survey mode
单选题
A blinking green power LED indicates which of the following conditions on a Cisco Series 1000 lightweight access point？（）
A
lost connection to the controller
B
duplicate IP address
C
startup
D
site survey mode
参考解析
解析：
暂无解析
相关考题：
A user reports it takes a long time to load all applications and the hard drive LED is showing constant activity. Which of the following is MOST likely the issue?() A. The processor is faulty.B. The file system is fragmented.C. The modem drivers are corrupt.D. The power supply is faulty.
When a user’s computer is first turned on, they see a lock symbol and a blinking cursor. Which of the following was configured in the BIOS to show this?() A. Intrusion detectionB. Power on passwordC. Drive encryptionD. BIOS password
Which of the following laptop displays has a thinner design, consumes less power, and is nottransparent?() A. PlasmaB. CCFL-backlit LCDC. OLEDD. LED-backlit LCD
A new floppy drive was just installed into a PC. The drive powers on at system boot but the status LED does not turn off during operation. Which of the following is MOST likely the issue?（）A、The power cable was installed incorrectly and needs to be flipped.B、The floppy drive was not enabled within the motherboard’s BIOS.C、The FDD cable was installed incorrectly and needs to be flipped.D、A Molex power cable was used instead of a Berg cable.
Which of the following laptop displays has a thinner design, consumes less power, and is nottransparent?（）A、PlasmaB、CCFL-backlit LCDC、OLEDD、LED-backlit LCD
During a system administrator attempt to boot a server in normal mode, the boot process displays LED 299 and Led 201 and then stops. The LED 201 indicates that a ROS init or checkstop was detected. Which of the following options is the most probable cause?（）A、A corrupted JFS log deviceB、A corrupted boot logical volumeC、An incorrect rc.boot entry in /etc/inittab fileD、A problem initializing paging space
Which of the following tools is BEST used to measure voltage and amperage from a power source?（）A、Loopback PlugB、MultimeterC、Power Supply TesterD、Extension Magnet
When a user’s computer is first turned on, they see a lock symbol and a blinking cursor. Which of the following was configured in the BIOS to show this?（）A、Intrusion detectionB、Power on passwordC、Drive encryptionD、BIOS password
A blinking green power LED indicates which of the following conditions on a Cisco Series 1000 lightweight access point？（）A、lost connection to the controllerB、duplicate IP addressC、startupD、site survey mode
On an Aironet card， LED 0 and LED 1 are blinking alternately. What does this indicate？ （）A、The Aironet card is in power save mode.B、The Aironet card is looking for a network association.C、The Aironet card is joined to a network， but there is no network activity.D、The Aironet card is joined to a network， and there is network activity.
Which of the following is the MOST likely to cause a server power supply fan to fail but allows the power supply to still be functional？（）A、DustB、Power SurgeC、Excessive humidityD、High temperatures
Which of the following is the correct wiring order for an RJ-11 two line jack？（）A、Black，Green，Red，YellowB、Black，Red，Green，YellowC、Red，Black，Green，YellowD、Yellow，Red，Green，Black
A user reports it takes a long time to load all applications and the hard drive LED is showing constant activity. Which of the following is MOST likely the issue?（）A、The processor is faulty.B、The file system is fragmented.C、The modem drivers are corrupt.D、The power supply is faulty.
Following a system boot，the display indicates that previously detected hardware is missing. Which of the following commands would identify the missing hardware？（）A、diagB、lscfgC、cfgmgrD、lsslot
Which of the following commands indicates the packet count for each interface？（）A、lsattrB、routeC、netstatD、ifconfig
A system was running properly until a reboot. Following the reboot， the system LED displayed cycles between 0223 and 0229. Which of the following procedures should be performed next？（）A、Power down then power up the systemB、Boot into diagnostic mode and run fsckC、Boot from installation media and run bosbootD、Boot into maintenance mode and check the bootlist
单选题Which of the following best indicates how many tons of cargo a ship can carry?（）.ABale cubicBDeadweightCGross tonnageDNet tonnage
单选题When a user’s computer is first turned on, they see a lock symbol and a blinking cursor. Which of the following was configured in the BIOS to show this?（）AIntrusion detectionBPower on passwordCDrive encryptionDBIOS password
单选题During a system administrator attempt to boot a server in normal mode, the boot process displays LED 299 and Led 201 and then stops. The LED 201 indicates that a ROS init or checkstop was detected. Which of the following options is the most probable cause?（）AA corrupted JFS log deviceBA corrupted boot logical volumeCAn incorrect rc.boot entry in /etc/inittab fileDA problem initializing paging space
单选题A user reports it takes a long time to load all applications and the hard drive LED is showing constant activity. Which of the following is MOST likely the issue?（）AThe processor is faulty.BThe file system is fragmented.CThe modem drivers are corrupt.DThe power supply is faulty.
单选题A system was running properly until a reboot. Following the reboot， the system LED displayed cycles between 0223 and 0229. Which of the following procedures should be performed next？（）APower down then power up the systemBBoot into diagnostic mode and run fsckCBoot from installation media and run bosbootDBoot into maintenance mode and check the bootlist
单选题A blinking green led indicates which of the following conditions on a cisco 1030 remote edge ap？（）AstartupBsite survey modeClost connection to the controllerDduplicate ip address
单选题A Cisco Aironet Wireless LAN Adapter CB21AG is inserted into a user’s PC cardbus slot. Both the green status LED and the amber activity LED are blinking slowly. What is the condition of the adapter？ （）AThe adapter is scanning for the wireless network for which it is configured.BThe adapter is in power save mode.CThe adapter is transmitting or receiving data while associated to an access point or another client.DThe adapter is not receiving power.EThe adapter is associated to an access point or another client.FNone of the other alternatives apply
单选题Which of the following indicates a grave and imminent danger requesting immediate assistance on radio telephone?（）.ASOSBMaydayCSecuriteDPAN
单选题A blinking green LED indicates which of the following conditions on a Cisco 1030 Remote EdgeAP？（）AstartupBsite survey modeClost connection to the controllerDduplicate IP address
单选题On an Aironet card， LED 0 and LED 1 are blinking alternately. What does this indicate？ （）AThe Aironet card is in power save mode.BThe Aironet card is looking for a network association.CThe Aironet card is joined to a network， but there is no network activity.DThe Aironet card is joined to a network， and there is network activity.
单选题Which of the following commands indicates when an interface has a multicast capability？（）AlsdevBlsattrCnetstatDifconfig