多选题A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）A172.16.0.1/23B172.16.1.1/26C172.16.1.1/24D172 .16.0.255/23ENone of the other answers is correct.
多选题
A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）
A
172.16.0.1/23
B
172.16.1.1/26
C
172.16.1.1/24
D
172 .16.0.255/23
E
None of the other answers is correct.
参考解析
解析：
暂无解析
相关考题：
How can a Ezonexam administrator determine if a router has been configured when it is first powered up?A．A configured router prompts for a passwordB．A configured router goes to the privileged mode promptC．An un configured router goes into the setup dialogD．An un configured router goes to the enable mode prompt
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP.Which of the following answers lists an item that cannot be matched by route map fred?（）A. Subnet numberB. Next - hop router IP address of the routeC. Whether the route is an E1 or E2 routeD. The ro ute‘s tagE. The number of router hops between the router and the subnet
Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? () A. The network has been stable for at least the last 45 minutesB. There is a flapping link or interf ace, and router C knows an alternate path to the networkC. There is a flapping link or interface, and router A does not know an alternate path to the networkD. EIGRP is not working correctly on router CE. There is not enough information to make a determination
Based on the exhibited output, which three statements are true?() A. The route to 10.2.0.0/16 was redistributed into EIGRP.B. A default route has been redistributed into the EIGRP autonomous system.C. R1 is configured with the ip summary - address command.D. R1 is sourcing a n external EIGRP route from Null0.E. The router at 10.1.1.2 is configured with the ip default - network 0.0.0.0 command.F. R1 is configured with the variance command.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero
A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）A. Router# show ip eigrp adjacencyB. Router# show ip eigrp topologyC. Router# show ip eigrp interfacesD. Router# show ip eigrp neighbors
A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which an swers list an IP address/prefix length that would cause the router to put Fa0/0 into area 9?（）A、172.16.0.1/23B、172.16.1.1/26C、172.16.1.1/24D、172.16.0.255/23E、None of the other answers is correct.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）A、Subnet numberB、Next - hop router IP address of the routeC、Whether the route is an E1 or E2 routeD、The ro ute's tagE、The number of router hops between the router and the subnet
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）A、The Gallant router has the wrong LMI type configuredB、Inverse ARP is providing the wrong PVC information to the Gallant routerC、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf commandD、The frame-relay map statement in the Attalla router for the PVC to Steele is not correctE、The IP address on the serial interface of the Attalla router is configured incorrectly
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode. Which of the following occurs？（）A、Fa0/0 failsB、The command is rejecteDC、The existing three neighbors failD、The neighborship with 172.16.2.20 fails and then reestablishesE、None of the other answers is correct
A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）A、Router# show ip eigrp adjacencyB、Router# show ip eigrp topologyC、Router# show ip eigrp interfacesD、Router# show ip eigrp neighbors
How can an administrator determine if a router has been configured when it is first powered up?（）A、A configured router prompts for a passwordB、A configured router goes to the privileged mode promptC、An un configured router goes into the setup dialogD、An un configured router goes to the enable mode prompt
Which three statements are true about EIGRP route summarization?（）A、When manual summarization is configured, the router immediately creates a route that points to null0 interfaceB、Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routingC、Manual route summarization is configured on the interfaceD、The ip summary - address eigrp command generates a default route with an administrative distance of 5E、When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routesF、The ip summary - address eigrp command generates a default route with an administrative distance of 90
A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）A、172.16.0.1/23B、172.16.1.1/26C、172.16.1.1/24D、172 .16.0.255/23E、None of the other answers is correct.
For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessaryB、The router must hav e at least one working link connected to each routing domainC、The redistribute command must be configured under EIGRP to send the routes to OSPFD、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
多选题HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP？ （）AHSRP provides redundancy and fault toleranceBHSRP allows one router to automatically assume the function of the second router if the second router failsCHSRP allows one router to automatically assume the function of the second router if the second router startsDHSRP provides redundancy and load balancing
多选题For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）AThe router must have one routing protocol configured, but configuration for both routing protocols is not necessaryBThe router must hav e at least one working link connected to each routing domainCThe redistribute command must be configured under EIGRP to send the routes to OSPFDThe redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
单选题A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）AThere is an error in the router DRAM.BTe IOS image is corrupt.CThe configuration register is set to 0x2142.DThe TFTP server that contains the router configuration file is unreachable.EA boot system configuration command has placed the router into setup mode.
单选题How can an administrator determine if a router has been configured when it is first powered up?（）AA configured router prompts for a passwordBA configured router goes to the privileged mode promptCAn un configured router goes into the setup dialogDAn un configured router goes to the enable mode prompt
多选题A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which an swers list an IP address/prefix length that would cause the router to put Fa0/0 into area 9?（）A172.16.0.1/23B172.16.1.1/26C172.16.1.1/24D172.16.0.255/23ENone of the other answers is correct.
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router
单选题Router R1 has been configured with the redistribute ospf 1 route - map fred command under router eigrp 1. The route map named fred needs to be configured to match routes to d etermine which routes are redistributed into EIGRP. Which of the following answers lists an item that cannot be matched by route map fred?（）ASubnet numberBNext - hop router IP address of the routeCWhether the route is an E1 or E2 routeDThe ro ute's tagEThe number of router hops between the router and the subnet