单选题What is the default metric used on IS -IS routers for each interface?（）AThe cost is set to 10 for all interfaces.BThe cost is set to 10 for LAN interfaces and 20 for WAN interfaces.CThe cost is based on the speed of the interface.DThe cost is based o n a composite of bandwidth and delay of the interface.
单选题
What is the default metric used on IS -IS routers for each interface?（）
A
The cost is set to 10 for all interfaces.
B
The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.
C
The cost is based on the speed of the interface.
D
The cost is based o n a composite of bandwidth and delay of the interface.
参考解析
解析：
暂无解析
相关考题：
In JUNOS software, what is the default interface metric for IS－IS?() A.1B.10C.100D.10^8/link bandwidth
What is the default metric used on IS －IS routers for each interface?() A. The cost is set to 10 for all interfaces.B. The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C. The cost is based on the speed of the interface.D. The cost is based o n a composite of bandwidth and delay of the interface.
Refer to the exhibit. In a redundant hub - and - spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0? Select the best response.（）A. Use address summarization at routers C, D, E, and FB. Use the EIGRP Stub featu re on routers C, D, E, and FC. Use passive - interface on the spoke links in routers A and BD. Change the administrative distance in routers A and B for routes learned from routers C, D, E,and F
Refer to the exhibit. Which th ree commands should be used on router B1 to redistribute the EIGRP AS 10 routes into RIP?() A. router ripB. router eigrp 10C. redistribute eigrp 10D. redistribute ripE. default - metric 10000 100 255 1 1500F. default - metric 5
Refer to the exhibit. A company would prefer all Internet - bound OSPF routed traffic to use ISP ABC with ISP DEF as a backup. As the network consultant, what three configuration changes might you make?（）A. The default -information originate command should be configured on router B1 and B4.B. The default -information originate command should be configured on router B2 and B3.C. If the metric value for ISP ABC is set at the default, the I SP DEF metric value should be set to 1.D. If the metric value for ISP ABC is set at the default, the ISP DEF metric value should be set to 25.E. The metric type value should be set to type 1.F. The metric type value should be set to type 2.
What is the IPv6 address FF02::2 used for?() A. all routers in a local segmentB. all routers in an autonomous systemC. all hosts in a local segmentD. all hosts in a particular multicast group
What is the default value of the SPT threshold in Cisco routers?() A. 0B. 1C. 2D. 4E. 16F. infinity
What is the default value of the SPT threshold in Cisco routers？（）A、 0B、 1C、 2D、 4E、 16F、 infinity
You are a technician at TestKing. Your newly appointed TestKing trainee wants to know what the CDP is.What would your reply be?（）A、It is globally enabled by default on Cisco routers.B、It is globally enabled by default on all routers.C、It is a proprietary protocol.D、It is a non-proprietary protocol.E、It can be used to gather hardware and protocol information about neighbor devices.
Which of the following is a valid method for defining a seed metric？（Choose all that apply.）（）A、The default-metric command configured under the appropriate interfaceB、The metric parameter in the network command of a routing processC、The metric parameter in the redistribute commandD、The default-metric commandE、A route-map containing a seed commandF、A route map containing a metric command
If a metric is not specified for routes that are redistributed into OSPF， the default metric that is assigned to the routes is 20， except for redistributed BGP routes. What is the metric that is assigned to redistributed BGP routes？（）A、0B、1C、10D、200
What is the default metric used on IS -IS routers for each interface?（）A、The cost is set to 10 for all interfaces.B、The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C、The cost is based on the speed of the interface.D、The cost is based o n a composite of bandwidth and delay of the interface.
In JUNOS software, what is the default interface metric for IS-IS?（）A、1B、10C、100D、10^8/link bandwidth
What is the meaning of the default value of the EIGRP variance command of 1? （）A、Only the path that is the feasible successor should be used.B、Load balancing is disabled on t his router.C、The router only performs equal - cost load balancing on all paths that have a metric greater than 1D、The router performs equal - cost load balancing.
Your network has a mixture of Fast Ethernet and Gigabit Ethernet links. What needs t o be done to ensure optimal data routing when using OSPF?（）A、Nothing. OSPF will determine the most optimal path for routing data by default.B、Adjust the hello and dead timers for more rapid detection of link failures.C、Increase the reference - bandw idth used to calculate the interface default metrics, on all routers in your network.D、Set the priority values on every broadcast interface to ensure that the designated and backup designated routers are the routers with the most processor and memory resources.
What is the IPv6 address FF02::2 used for?（）A、all routers in a local segmentB、all routers in an autonomous systemC、all hosts in a local segmentD、all hosts in a particular multicast group
Routers A and B have an OC12c and a GE link between them and are running OSPF over both of these links.Which item is correct， assuming the default JUNOS software OSPF metric calculation？（）A、There are two equal cost paths between A and BB、The GE link is the preferred path between A and BC、The OC12c link is the preferred path between A and BD、Manual metric assignment must be configured to determine the outcome.
Your network contains a server named Server1. Server1 runs Windows Server 2008 R2 and has a single network connection. The connection is configured to use a default gateway address of 10.0.0.1.The default gateway has a metric value of 100.You configure a second default gateway that uses an address of 10.0.0.2.You need to ensure that 10.0.0.2 is only used as the default gateway if 10.0.0.1 is unreachable. What should you do？（）A、For the interface, set the interface metric to 100.B、For the 10.0.0.2 gateway, set the metric to 50.C、For the 10.0.0.2 gateway, set the metric to 200.D、For the 10.0.0.1 gateway and the 10.0.0.2 gateway, enable automatic metric.
多选题Process EIGRP 1 is redistributing routes from process OSPF 2. Which two of the following methods may be used to set the metrics of the redistributed routes?（）ALet the metrics default.BSet the metric components using the redistri bute command's metric keyword.CSet the metric components using the default - metric router subcommand.DSet the integer (composite) metric using the redistribute command's metric keyword.
多选题You are a technician at TestKing. Your newly appointed TestKing trainee wants to know what the CDP is.What would your reply be?（）AIt is globally enabled by default on Cisco routers.BIt is globally enabled by default on all routers.CIt is a proprietary protocol.DIt is a non-proprietary protocol.EIt can be used to gather hardware and protocol information about neighbor devices.
单选题What is the meaning of the default value of the EIGRP variance command of 1? （）AOnly the path that is the feasible successor should be used.BLoad balancing is disabled on t his router.CThe router only performs equal - cost load balancing on all paths that have a metric greater than 1DThe router performs equal - cost load balancing.
单选题In JUNOS software, what is the default interface metric for IS-IS?（）A1B10C100D10^8/link bandwidth
单选题On a Juniper router， what is the default file used for syslog messages？（）AsystemBerrorsCsecurityDmessages
多选题Process OSPF 1 is redistributing routes from process OSPF 2. Which of the following methods may be used to set the metrics of the redistributed routes?（）ALet the metrics default.BUse each redistributed route's OSPF metric using the redistribute command's metric transparent keywords.CSet the metric using the default - metric router subcommand.DRedistribution is not allowed between two OSPF p rocesses.
多选题Which of the following is a valid method for defining a seed metric？（Choose all that apply.）（）AThe default-metric command configured under the appropriate interfaceBThe metric parameter in the network command of a routing processCThe metric parameter in the redistribute commandDThe default-metric commandEA route-map containing a seed commandFA route map containing a metric command
单选题If a metric is not specified for routes that are redistributed into OSPF， the default metric that is assigned to the routes is 20， except for redistributed BGP routes. What is the metric that is assigned to redistributed BGP routes？（）A0B1C10D200