单选题In JUNOS software, what is the default interface metric for IS-IS?（）A1B10C100D10^8/link bandwidth
单选题
In JUNOS software, what is the default interface metric for IS-IS?（）
A
1
B
10
C
100
D
10^8/link bandwidth
参考解析
解析：
暂无解析
相关考题：
How is the cost of a virtual link in OSPF calculated?() A. Takes the metric of the outgoing interface.B. Uses the metric that is assigned during configuration.C. Uses the path metric to reach the virtual link neighbor.D. Uses a default of zero unless otherwise specified.
By default, which IS－IS metric types does JUNOS software support?() A. receiving of wide metrics onlyB. sending of narrow metrics onlyC. receiving of narrow metrics onlyD. sending and receiving of narrow and wide metrics
In JUNOS software, what is the default interface metric for IS－IS?() A.1B.10C.100D.10^8/link bandwidth
What is the default metric used on IS －IS routers for each interface?() A. The cost is set to 10 for all interfaces.B. The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C. The cost is based on the speed of the interface.D. The cost is based o n a composite of bandwidth and delay of the interface.
In JUNOS software, what is the purpose of the eui-64 command?（）A、Automatically create the IS-IS NET id.B、Dynamically create an OSPFV3 router idC、Automatically assign the host portion of an ipv6 address.D、Dynamically assign amac address to an ethernet interface.
If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?（）A、1B、64C、1562D、64000E、1500
If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）A、1B、10C、1562D、64000E、128000F、None of the above
What is the default metric used on IS -IS routers for each interface?（）A、The cost is set to 10 for all interfaces.B、The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.C、The cost is based on the speed of the interface.D、The cost is based o n a composite of bandwidth and delay of the interface.
Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）A、set interfaces ge-0/3/0 unit 0 metric 10B、set protocols ospf reference-bandwidth 10gC、set interfaces ge-0/3/0 unit bandwidth 10gD、set protocols ospf area 0 interface ge-0/3/0 metric 10E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
In JUNOS software, what is the default interface metric for IS-IS?（）A、1B、10C、100D、10^8/link bandwidth
In JUNOS software， what is the purpose of the eui-64 command？（）A、Automatically create the IS-IS NET IDB、Dynamically create an MPLS router IDC、Automatically assign the host number of an IPv6 address.D、Dynamically assign a MAC address to an Ethernet interface.
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）A、1B、10C、1562D、64000E、128000
By default, which IS-IS metric types does JUNOS software support?（）A、receiving of wide metrics onlyB、sending of narrow metrics onlyC、receiving of narrow metrics onlyD、sending and receiving of narrow and wide metrics
How is the cost of a virtual link in OSPF calculated?（）A、Takes the metric of the outgoing interface.B、Uses the metric that is assigned during configuration.C、Uses the path metric to reach the virtual link neighbor.D、Uses a default of zero unless otherwise specified.
Routers A and B have an OC12c and a GE link between them and are running OSPF over both of these links.Which item is correct， assuming the default JUNOS software OSPF metric calculation？（）A、There are two equal cost paths between A and BB、The GE link is the preferred path between A and BC、The OC12c link is the preferred path between A and BD、Manual metric assignment must be configured to determine the outcome.
What is the default hello interval for RSVP in the JUNOS software?（）A、1 secondB、3 secondsC、9 secondsD、12 seconds
Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）A、set interfaces ge-0/3/0 unit 0 metric 10B、set protocols ospf reference-bandwidth 10gC、set interfaces ge-0/3/0 unit 0 bandwidth 10gD、set protocols ospf area 0 interface ge-0/3/0 metric 10E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
Routers A and B have an OC12c and a GE link between them and are running OSPF over both ofthese links. Which statement is correct, assuming the default JUNOS software OSPF metric calculation?（）A、There are two equal cost paths betweena and b.B、Thege link is the preferred path betweena and b.C、The oc12c link is the preferred path betweena and b.D、Manual metric assignment must be configured to determine the outcome
单选题Routers A and B have an OC12c and a GE link between them and are running OSPF over both ofthese links. Which statement is correct, assuming the default JUNOS software OSPF metric calculation?（）AThere are two equal cost paths betweena and b.BThege link is the preferred path betweena and b.CThe oc12c link is the preferred path betweena and b.DManual metric assignment must be configured to determine the outcome
单选题How is the cost of a virtual link in OSPF calculated?（）ATakes the metric of the outgoing interface.BUses the metric that is assigned during configuration.CUses the path metric to reach the virtual link neighbor.DUses a default of zero unless otherwise specified.
单选题How is the cost of a virtual link in OSFP calculated？（）ATakes the metric of the outgoing interface.BUses the metric that is assigned during configuration.CUses the path metric to reach the virtual neighbor.DUses a default of zero unless otherwise specified.
单选题By default, which IS-IS metric types does JUNOS software support?（）Areceiving of wide metrics onlyBsending of narrow metrics onlyCreceiving of narrow metrics onlyDsending and receiving of narrow and wide metrics
单选题What is the default metric used on IS -IS routers for each interface?（）AThe cost is set to 10 for all interfaces.BThe cost is set to 10 for LAN interfaces and 20 for WAN interfaces.CThe cost is based on the speed of the interface.DThe cost is based o n a composite of bandwidth and delay of the interface.
单选题If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）A1B10C1562D64000E128000FNone of the above
单选题In JUNOS software， what is the purpose of the eui-64 command？（）AAutomatically create the IS-IS NET IDBDynamically create an MPLS router IDCAutomatically assign the host number of an IPv6 address.DDynamically assign a MAC address to an Ethernet interface.
单选题Routers A and B have an OC12c and a GE link between them and are running OSPF over both of these links.Which item is correct， assuming the default JUNOS software OSPF metric calculation？（）AThere are two equal cost paths between A and BBThe GE link is the preferred path between A and BCThe OC12c link is the preferred path between A and BDManual metric assignment must be configured to determine the outcome.
单选题In JUNOS software, what is the purpose of the eui-64 command?（）AAutomatically create the IS-IS NET id.BDynamically create an OSPFV3 router idCAutomatically assign the host portion of an ipv6 address.DDynamically assign amac address to an ethernet interface.