Refer to the exhibit. This network is running IS － IS. Router RTC is inside Cloud1. From the output on RTD, which two statement s are true?() A.Because it is running IS - IS in IP - only mode, RTD will not transmit CLNS packetsB.IP routing updates between RTC and RTD will be IP datagrams that are encapsulated by HDLCC.The SNPA for RTE is the source data link address that is used to transmit frames to RTDD.IP routing updates between RTC and RTD will be CLNS datagrams that are encapsulated by HDLCE.The NET for RTE will be 49.0150.0019.06b7.fd5f.00F.IP routing updates between RTC and RTD will be IP datagrams that a re encapsulated by CLNS
Refer to the exhibit. This network is running IS － IS. Router RTC is inside Cloud1. From the output on RTD, which two statement s are true?()
A.Because it is running IS - IS in IP - only mode, RTD will not transmit CLNS packets
B.IP routing updates between RTC and RTD will be IP datagrams that are encapsulated by HDLC
C.The SNPA for RTE is the source data link address that is used to transmit frames to RTD
D.IP routing updates between RTC and RTD will be CLNS datagrams that are encapsulated by HDLC
E.The NET for RTE will be 49.0150.0019.06b7.fd5f.00
F.IP routing updates between RTC and RTD will be IP datagrams that a re encapsulated by CLNS
相关考题：
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. Which statement about dynamic routing protocols for this network is true? () A.No dynamic interior routing protocol can summarize as shownB.Unless configured otherwise, EIGRP would automatically summa rize the prefixes as shown in the exhibitC.With this IP addressing scheme, EIGRP can be manually configured to summarize prefixes at the specified summarization pointsD.The IP address design lends itself to OSPF Each summarizing router would be an ABR, summarizing to the next area in the address hierarchy
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
Refer to the exhibit. The partial configuration for an OSPF ASBR and an Area 0 ABR is shown. Assume the OSPF configurations throughout the network are operable. Which statement about these configurations is true? （）A. The ASBR route - maps are basically useless, because there are no deny prefix - lists.B. LSA Type 5s wil l not be received by the ABR from the ASBR.C. The OSPF backbone will not learn any RFC 1918 addresses.D. The matched prefix - list addresses will be given a metric of 255, which is essentially unreachable.
Refer to the above exhibit. Why is the 140.140.0.0 network not used as the gateway of last resort even though it is configured first?() A.The last default - network statement will always be preferred.B.A route to the 140.140.0.0 network does not exist in the routing table.C.Default - network selection will always prefer the statement with the lowest IP address.D.A router will load balance across multiple default - networks; repeatedly issuing the show ip route command would show the gateway of last resort changing between the two networks.
Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? () A.The NProuter has two OSPF neighbors in the Full adjacency stateB.The NProuter serial0/0 interface has the OSPF dead timer set to 10 secondsC.The NProuter serial0/0 interface has been configured with an OSPF network type of pointtopointD.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers settingE.The Mismatched error is caus ed by the expiration of the OSPF timers
Refer to the exhibit. Routing updates for the 192.168.1.0 network are being received from all three neighbors. Which statement is correct regarding the result of the con figuration shown? () A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.C. The router will adve rtise the 192.168.1.0 network only to 172.30.1.1.D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.
Refer to the exhibit. Which statement is true about the router configuration that is shown ?Select the best response.() A. Additional DHCP options will be imported from another DHCP server.B. The DHCP server pools need to be bound to an interface to operate.C. This configuration will provide IP configuration information to two different su bnets.D. Additional DCHP option information needs to be imported from another DHCP server.E. If the router hands out all the addresses in pool 1, then it will supply addresses from pool 2.
Refer to the exhibit. Which statement is true? () A. Only traffic with a destination from 10.10.0.0/19 will be permitted.B. Router RAR1 will accept only route 10.10.0.0/19 from its BGP neighbor.C. Only traffic going to 10.10.0.0/19 will be permitted.D. Router RAR1 will send only route 10.10.0.0/19 to its BGP neighbor.
Refer to the exhibit. Which two conclusions can be drawn from the debug ip igmp output?() A. The router sent an IGMP version 2 query out interface Ethernet1 at multicast address 224.0.0.1.B. Router RTA received an IGMP report version 1 from host 192.168.9.1.C. Reverse Path Forwarding (RPF) is ena bled for 192.168.9.4.D. Reverse Path Forwarding (RPF) is enabled for 224.0.1.40.E. The IP multicast groups are 224.0.0.1, 224.0.1.40, and 239.255.0.1.F. IP PIM RP mapping is static.
Refer to the exhibit. By default, when RTB passes BGP advertisements from RTA about network 192.168.2.0 to RTC, what address will be listed as the next － hop address? () A. 10.1.1.2B. 192.168.1.49C. 10.1.1.1D. 192.168.1.50
Refer to the exhibit. Which two statement s are correct?() A. All the routes were redistributed into BGP from an IGPB. All the routes were originated by BGP with the network commandC. All six routes will be installed in the routing tableD. Four routes will be installed in the routing ta bleE. Two routes will be installed in the routing table
Refer to the exhibit. Which st atement is true?() A. Router RTA is the BDRB. Router RTA is directly connected to interface 192.168.45.1C. Neighbor 192.168.45.1 has changed its OSPF priority numberD. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs
Refer to the exhibit. Which statement is true about the configuration? () A. RTA will not establish an OSPF adjacency w ith RTBB. RTA will send OSPF hello packets, but will not send OSPF updatesC. RTA will not accept OSPF hello packets from RTBD. RTA will send OSPF updates, but will not establish an adjacency with RTB
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true? () A. Both outgoing and incoming routing updates on R1 will be permitted because the d istribute - list 20 out Serial0/0 command cannot be used with association with the outgoing interface.B. All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.C. Both outgoing and incoming routing up dates on R1 will be stopped because of the passive - interface Serial0/0 configuration statement.D. All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 ／26 and 172.16.1.64 ／27. On the basis of the partial output in the exhibit, which statement is true? () A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.B. Router R1 will advertise both rou tes.C. Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）A.Check and change the access lists on router RTAB.Configure the auto summary command under router eigrp 1 on router RTAC.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterfaceD.Issue the no ip split horizon command on router RTAE.Issue the no ip split horizon eigrp 1 command on router RTAF.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers
Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）A.The Manchester serial address is 10.1.1.1B.The Manchester serial address is 10.1.1.2C.这个Manchester路由器串口地址为：10.1.12D.The London router is a Cisco 2610.E.The Manchester router is a Cisco 2610.F.The CDP information was received on port Serial0/0 of the Manchester router.G.The CDP information was sent by port Serial0/0 of the London Router.
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A、As numbers must be changed to match on all the routers.B、Loopback interface must be configured so a DR is elected.C、The no auto-summary command is needed on Router A and Router C.D、Router B needs to have two network statements, one for each connected network.
Refer to the exhibit. Which statement is correct based on the show login command output shown？（）A、When the router goes into quiet mode， any host is permitted to access the router via Telnet，SSH， and HTTP，since the quiet-mode access list has not been configured.B、The login block-for command is configured to block login hosts for 93 seconds.C、All logins from any sources are blocked for another 193 seconds.D、Three or more login requests have failed within the last 100 seconds.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
单选题Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）AAs numbers must be changed to match on all the routers.BLoopback interface must be configured so a DR is elected.CThe no auto-summary command is needed on Router A and Router C.DRouter B needs to have two network statements, one for each connected network.
多选题Refer to the exhibit. Which two statements are correct？（）AAll six routes will be installed in the routing tableBTwo routes will be installed in the routing tableCFour routes will be installed in the routing tableDAll the routes were redistributed into BGP from an IGPEAll the routes were originated by BGP with the network command
多选题Refer to the exhibit. On the basis of the information in the exhibit， which two statements are true？（）AWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2BThe serial 0/0/1 interface on the ISP router has been configured with the set metric 50commandCThe output was generated by entering the show ip bgp command on the SanJose1 routerDThe output was generated by entering the show ip bgp command on the ISP routerEThe serial 0/0/1 interface on the ISP router has been configured with the set metric 75commandFWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
单选题Refer to the exhibit. Which statement is true about a voice VLAN？（）A Physically the voice network and the data network are separateB The voice traffic will normally be on a different IP subnet than will the data trafficC End user intervention is necessary to place the phone into the proper VLAND The same security policy should be implemented for both voice and data trafficE The data VLAN must be configured as the native VLAN
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router