Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）A. router bgp 1B. neighbor 2.2.2.2 remote- as 2C. neighbor 2.2.2.2 update - source loopback1D. neighbor 2.2.2.2 multihop 2
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）
A. router bgp 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 multihop 2
相关考题：
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router‘s logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）A. When the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interfaceB. When routing the packet, matching a route whose outgoing interface is the GRE tunnel interfaceC. When routing the packet, matching a route whose outgoing interface is the IPsec tunnel interfaceD. When permitted by an ACL that was referenced in the associated crypto map
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）A. PPP on the ATM interfaceB. VPI/VCI on the dialer interfaceC. IP address on the ATM interfaceD. CHAP on the dialer interface
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）A. PrivacyB. AuthenticationC. Allows using an IGP between R1 and the EnterpriseD. Secure communications
A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers.Which of the following could be used to prevent potential routing loops in this design?（）A. Using an iBGP mesh inside the Enterprise coreB. Configuring default routes in the Enterprise pointing to both R1 and R2C. Redistributing BGP routes into the Enterprise IGPD. Tunneling the packets for the i BGP connection between R1 and R2
Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A. 22B. 11C. 1D. None
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）A. ip ospf network broadcastB. ip ospf network non - broadcastC. ip ospf network point - to - multipointD. ip ospf network point - to - multipoint non - broadcast
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）A、router bgp 2B、router bgp 1C、neighbor 10.1 .1.2 remote - as 2D、neighbor 10.1.1.2 Update - source 10.1.1.1E、neighbor 10.1.1.2 Update- source S0/0
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）A、router bgp 1B、neighbor 2.2.2.2 remote- as 2C、neighbor 2.2.2.2 update - source loopback1D、neighbor 2.2.2.2 multihop 2
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection. Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）A、By not enabling NAT on the I Psec tunnel interfaceB、By not enabling NAT on the GRE tunnel interfaceC、By configuring the NAT - referenced ACL to not permit the Enterprise trafficD、By asking the ISP to perform NAT in the cloud
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise. Which of the following is most likely to be useful on the branch router?（）A、IPsec tunnelB、GRE tunnelC、Floating stati c routeD、An IGP
Enterprise Router R1 connects an Enterprise to the Internet. R1 needs to create and advertise a default route into the Enterprise using EIGRP. The engineer creating the implementation plan has chosen to base this default route on the ip route command, rather than using i p default - network. Which of the following is not a useful step with this style of default route configuration?（）A、Create the default route on R1 using the ip route 0.0.0.0 0.0.0.0 outgoinginterface command.B、Redistribute the statically configured defa ult route.C、Disable auto - summary.D、Configure the network 0.0.0.0 command.E、Ensure R1 has no manually configured summary routes using the ip summary- address eigrp command.
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（） Network Next Hop Metric LocPrf Weight Path * 3.3.3.3 0 0 1 1 1 1 2 18 iA、The Enterprise likely uses ASN 1.B、The neighboring ISP likely uses ASN 1.C、The route has been advertised through ASN 1 multiple times.D、Router Ent1 will add another ASN to the AS_Path before advertising this route to its iBGP peer (4.4.4.4).
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）A、ip ospf network broadcastB、ip ospf network non - broadcastC、ip ospf network point - to - multipointD、ip ospf network point - to - multipoint non - broadcast
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
Which of the following statements is true about a router's eBGP peers that is not also true about that same router's iBGP peers?（）A、The eBGP peer neighborship uses TCPB、The eBGP peer uses port 180 (default)C、The eBGP peer uses the same ASN as the local routerD、The eBGP peer updates its AS_Path PA before sending updates to this router
单选题Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE. Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）APrivacyBAuthenticationCAllows using an IGP between R1 and the EnterpriseDSecure communications
单选题Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）A22B11C1DNone
单选题Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）Arouter bgp 1Bneighbor 2.2.2.2 remote- as 2Cneighbor 2.2.2.2 update - source loopback1Dneighbor 2.2.2.2 multihop 2
多选题Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）Arouter bgp 2Brouter bgp 1Cneighbor 10.1 .1.2 remote - as 2Dneighbor 10.1.1.2 Update - source 10.1.1.1Eneighbor 10.1.1.2 Update- source S0/0
单选题Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured. Which combinations accurately describe the interface under which a feature will be configured?（）APPP on the ATM interfaceBVPI/VCI on the dialer interfaceCIP address on the ATM interfaceDCHAP on the dialer interface
单选题An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（） Network Next Hop Metric LocPrf Weight Path * 3.3.3.3 0 0 1 1 1 1 2 18 iAThe Enterprise likely uses ASN 1.BThe neighboring ISP likely uses ASN 1.CThe route has been advertised through ASN 1 multiple times.DRouter Ent1 will add another ASN to the AS_Path before advertising this route to its iBGP peer (4.4.4.4).
多选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers. Which of the following could be used to prevent potential routing loops in this design?（）AUsing an iBGP mesh inside the Enterprise coreBConfiguring default routes in the Enterprise pointing to both R1 and R2CRedistributing BGP routes into the Enterprise IGPDTunneling the packets for the i BGP connection between R1 and R2
单选题Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network. Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）AWhen the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interfaceBWhen routing the packet, matching a route whose outgoing interface is the GRE tunnel interfaceCWhen routing the packet, matching a route whose outgoing interface is the IPsec tunnel interfaceDWhen permitted by an ACL that was referenced in the associated crypto map
多选题An engineer has been told to create an implementation plan to influence the choice of best BGP route on a single router using the Weight featurE. The sole Enterprise Internet - connected router, Ent 1, has neighbor relationships with Routers ISP1 and ISP2, which reside inside two different ISPs. The goal is to prefer all routes learned from ISP1 over ISP2 using Weight. Which of the following answers lists a configuration step that would not be usefu l for achieving these goals?（）AConfiguring the neighbor weight command on Ent1.BHaving the ISPs configure the neighbor route - map out command on ISP1 and ISP2, with the route map setting weight.CConfiguring the set weight command inside a route map on Router Ent1.DConfiguring a prefix list to match all class C networks.
多选题Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise. Which of the following is most likely to be useful on the branch router?（）AIPsec tunnelBGRE tunnelCFloating stati c routeDAn IGP
单选题Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection. Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）ABy not enabling NAT on the I Psec tunnel interfaceBBy not enabling NAT on the GRE tunnel interfaceCBy configuring the NAT - referenced ACL to not permit the Enterprise trafficDBy asking the ISP to perform NAT in the cloud