Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1‘s configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2.Which answer gives the reason for the omission?()A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.B. S0/2 may currently be in a state other than up/up.C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.D. S0/2 may be configured as a passive inter face.

Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1‘s configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2.Which answer gives the reason for the omission?()

A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.

B. S0/2 may currently be in a state other than up/up.

C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.

D. S0/2 may be configured as a passive inter face.


相关考题:

下表是该系统中路由器的IP地址分配表。请根据上图完成以下R3路由器的配置:R3(config)interface e0/1(进入接口e0/1配置模式)R3(coafig-if) ip address 202.115.13.254(4)(设置IP地址和掩码)R3(config) interface s0/0(进入串口配置模式)R3(config-if) ip address(5)255.255.255.0(设置IP地址和掩码)R3(config) interface s0/1R3(config-if)ip address(6)255.255.255.0R3(config) interface s0/2R3(eonfig-if)ip address(7)255.255.255.0R3(config) interface s0/3R3(eonfig-if)ip address(8)255.255.255.0R3(config) interface s0/4R3(config-if)ip address(9)255.255.255.0R3(config) interface s0/5R3(config-if) ip address(10)255.255.255.0

该网络的Internet接入如图12-11所示:根据图12-11,解释以下配置命令,填写空格(9)~(12):1.Router(config) interface s0/02.router(config-if) ip address 61.235.1.1 255.255.255.252(9)3.router(config) ip route 0.0.0.0 0.0.0.0 s0/0(10)4.router(config) ip route 192.168.0.0 255.255.255.0 f0/0(11)5.router(config) access-list 100 deny any any eq telnet(12)

Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?() A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID

Refer to the exhibit.The network administrator is in acampus building distant from Building B.WANRouter is hosting a newly installed WAN link on interface S0/0.The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface.How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner?()A.Telnet to WANRouter and execute the command show interfaces S0/0B.Telnet to WANRouter and execute the commandshow processes S0/0C.Telnet to WANRouter and execute the command show running-configurationD.Telnet to WANRouter and execute the command show controller S0/0E.Physically examine the cable between WANRouter S0/0 and the DCE.F.Establish a console sessionon WANRouter and execute the command show interfaces S0/0

Whatcanbedetermined fromthelineofshowiprouteoutputshownintheexhibit?() A.The next routing update can be expected in 35 seconds.B.The IP address 10.10.10.6 is configured on S0/1.C.The IP address 10.10.10.8 is configured on S0/1.D.This route is using the default administrative distance.E.The 10.10.10.8 network is two hops away from this router.

What can be determined from the line of show ip route output shown in the exhibit?()A、The next routing update can be expected in 35 seconds.B、The IP address 10.10.10.6 is configured on S0/1.C、The IP address 10.10.10.8 is configured on S0/1.D、This route is using the default administrative distance.E、The 10.10.10.8 network is two hops away from this router.

Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request()。A、The Mac address of the NIC in Sever1B、The IP address of Server 1.C、The MAC address of the s0/0/0 interface of router R2D、The IP address of the s0/0/0 interface of router R1E、The IP address of the Fa0/0 interface of router R1

Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?()A、R1 limi ts EIGRP to around 250Kbps on DLCI 102B、R1 limits EIGRP to around 250Kbps on DLCI 104C、R1 limits EIGRP to around 150Kbps on every DLCID、R1 does not limit EIGRP because noWAN bandwidth control has been configured

Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?()A、router bgp 2B、router bgp 1C、neighbor 10.1 .1.2 remote - as 2D、neighbor 10.1.1.2 Update - source 10.1.1.1E、neighbor 10.1.1.2 Update- source S0/0

Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet()。A、The IP address of sever 1.B、The MAC address of NIC in sever 1.C、The IP address of F0/0 interface of router R1.D、The MAC address of the Fa0/0 interface of router R1.E、The IP address of the s0/0/0 interface of router R2F、The MAC address of the s0/0/0 interface of router R2

Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()A、MetricB、Administrative distanceC、Timeout (seconds)D、Prefix lengthE、Interface ID

Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()A、FEA0::200:FF:FE11:0B、FE80::200:FF:FE11:1111C、FE80::0213:19FF:FE7B:0:1D、FEB0::211:11FF:FE11: 1111

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?() ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1A、EIGRP works on F0/0 and S0/0/0 without further configurationB、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modEC、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modED、EIGRP for IPv6 needs at least two more configuration commands before it works on R1

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?() ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enableA、RIPng will be enabled on no interfaces.B、RIPng will be enabled on one interface.C、RIPng will be enabled on two interfaces.D、RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission?()A、R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.B、S0/2 may currently be in a state other than up/up.C、The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.D、S0/2 may be configured as a passive inter face.

The network administrator is in a campus building distant from Building B. WANRouter is hosting a newly installed WAN link on interface S0/0. The new link is not functioning and the administrator needs to determine if the correct cable has been attached to the S0/0 interface. How can the administrator accurately verify the correct cable type on S0/0 in the most efficient manner()。A、Telnet to WANRouter and execute the command show interfaces S0/0B、Telnet to WANRouter and execute the command show processes S0/0C、Telnet to WANRouter and execute the command show running-configurationD、Telnet to WANRouter and execute the command show controller S0/0E、Physically examine the cable between WANRouter S0/0 and the DCEF、Establish a console session on WANRouter and execute the command show interfaces S0/0

Examine the following configuration on Router R1. R1's show ip route 172.16.4.1 command list s a route with outgoing interface S0/1/1. Host 172.16.3.3 uses telnet to connect to host 172.16.4.1.What will Router R1 do with the packets generated by host 172.16.3.3 because of the telnet,assuming the packets enter R1's F0/0 interface?() interface Fastethernet 0/0 ip address 172.16.1.1 255.255.255.0 ip policy route - map Q2 ! route - map Q2 permit match ip address 101 set interface s0/0/1 ! access - list 101 permit tcp host 172.16.3.3 172.16.4.0 0.0.0.255A、The packet will be forwarded out S0/0 /1, or not at all.B、The packet will be forwarded out S0/0/1 if it is up.C、The packet will be forwarded out S0/1/1 if it is up.D、The packet will be forwarded out S0/1/1 if it is up, or if it is not up, out s0/0/1.E、The packet will be forwarded o ut S0/0/1 if it is up, or if it is not up, out s0/1/1.

单选题Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?()AFEA0::200:FF:FE11:0BFE80::200:FF:FE11:1111CFE80::0213:19FF:FE7B:0:1DFEB0::211:11FF:FE11: 1111

单选题Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request()。AThe Mac address of the NIC in Sever1BThe IP address of Server 1.CThe MAC address of the s0/0/0 interface of router R2DThe IP address of the s0/0/0 interface of router R1EThe IP address of the Fa0/0 interface of router R1

单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?() ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0AOSPF works on F0/0 and S0/0/0 without further configurationBOSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modECOSPF works with the addition of one command: an router - id command in OSPF router configuration modEDOSPFv3 needs at least two more configuration commands before it works on R1

多选题What can be determined from the line of show ip route output shown in the exhibit?()AThe next routing update can be expected in 35 seconds.BThe IP address 10.10.10.6 is configured on S0/1.CThe IP address 10.10.10.8 is configured on S0/1.DThis route is using the default administrative distance.EThe 10.10.10.8 network is two hops away from this router.

多选题Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?()Arouter bgp 2Brouter bgp 1Cneighbor 10.1 .1.2 remote - as 2Dneighbor 10.1.1.2 Update - source 10.1.1.1Eneighbor 10.1.1.2 Update- source S0/0

单选题Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all. Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?()AR1 limi ts EIGRP to around 250Kbps on DLCI 102BR1 limits EIGRP to around 250Kbps on DLCI 104CR1 limits EIGRP to around 150Kbps on every DLCIDR1 does not limit EIGRP because noWAN bandwidth control has been configured

单选题R1 forwards a packet from Host 1 to remote Server 1. Which statement describes the use of a MAC as the frame carrying this packet leaves the s0/0/0 interface of R1()。AThe frame does not have MAC addresses.BThe source MAC address in the frame is the MAC address of the NIC of Host 1.CThe source MAC address in the frame is the MAC address of the s0/0/0 interface of R1.DThe destination MAC address in the frame is the MAC address of the NICof server 1.EThe destination MAC address in the frame is the MAC address of the s0/0/0 interface of R2

单选题Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet()。AThe IP address of sever 1.BThe MAC address of NIC in sever 1.CThe IP address of F0/0 interface of router R1.DThe MAC address of the Fa0/0 interface of router R1.EThe IP address of the s0/0/0 interface of router R2FThe MAC address of the s0/0/0 interface of router R2

单选题Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission?()AR1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.BS0/2 may currently be in a state other than up/up.CThe network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.DS0/2 may be configured as a passive inter face.

单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?() ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enableARIPng will be enabled on no interfaces.BRIPng will be enabled on one interface.CRIPng will be enabled on two interfaces.DRIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

单选题Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()AMetricBAdministrative distanceCTimeout (seconds)DPrefix lengthEInterface ID