Refer to the exhibit. IP multicast for group address 224.1.1.1 has been enabled on all router s in the network. Hosts on Network A receive the multicast traffic. However, hosts on Network B do not. On the basis of outputs provided, what could be the cause of the problem? （）A. The route to 224.69.15.0/24 will be out Ethernet 0B. The reverse path forwarding (RPF) for the route 224.2.0.1 failed to find the interface on which the multicast packet was rece ivedC. Multicast route to 224.69.15.0/24 was added to the mroute table and created by a source directly connected to the routerD. Multicast route to 10.16.0.0/16 was added to the mroute table and created by a source directly connected to the routerE. This router received an IGMP host report from a group member or a PIM join message
Refer to the exhibit. IP multicast for group address 224.1.1.1 has been enabled on all router s in the network. Hosts on Network A receive the multicast traffic. However, hosts on Network B do not. On the basis of outputs provided, what could be the cause of the problem? （）
A. The route to 224.69.15.0/24 will be out Ethernet 0
B. The reverse path forwarding (RPF) for the route 224.2.0.1 failed to find the interface on which the multicast packet was rece ived
C. Multicast route to 224.69.15.0/24 was added to the mroute table and created by a source directly connected to the router
D. Multicast route to 10.16.0.0/16 was added to the mroute table and created by a source directly connected to the router
E. This router received an IGMP host report from a group member or a PIM join message
相关考题：
Typically, an IP address refers to an individual host on a particular network. IP also accommodates addresses that refer to a group of hosts on one or more networks. Such addresses are referred to as multicast addresses, and the act of sending a packet from a source to the members of a （1）group is referred to as multicasting. Multicasting done （2）the scope of a single LAN segment is straightforward. IEEE 802 and other LAN protocols include provision for MAC-level multicast addresses. A packet with a multicast address is transmitted on a LAN Segment. Those stations that are members of the （3）multicast group recognize the multicast address and （4）the packet. In this case, only a single copy of the packet is ever transmitted. This technique works because of the （5）nature of a LAN: A transmission from any one station is received by all other station on the LAN.A.numerousB.onlyC.singleD.multicast@@@SXB@@@A.withinB.out ofC.beyondD.cover@@@SXB@@@A.differentB.uniqueC.specialD.corresponding@@@SXB@@@A.rejectB.acceptC.discardD.transmit@@@SXB@@@A.multicastB.unicastC.broadcastD.multiple unicast
Refer to the exhibit. Which statement is co rrect regarding the router configuration shown? () A. The router will rebroadcast any DHCP requests received by this interface out to all interfaces included in the ip helper - address commands.B. The router will rebroadcast any UDP broadcasts received by this interface out to all interfaces included in the ip helper - address commands.C. The router will unicast any DHCP requests received by this interface out to all addresses included in the ip helper - address commands.D. This configuration will not do anything because the ip helper - address command needs to also be applied to the 192.168.23.1 IP address.
Refer to the exhibit. On the basis of the output, what two conclusions can be reached?() A. The default administrative distance has been changed.B. IS - IS is not enabled.C. Three physical interfaces are taking part in integrated IS - IS.D. IS - IS is not redistributing any oth er routing protocols.E. There are two neighboring routers sending IS - IS routing information.F. Address summarization is configured.
Refer to the exhibit. Which two conclusions can be drawn from the debug ip igmp output?() A. The router sent an IGMP version 2 query out interface Ethernet1 at multicast address 224.0.0.1.B. Router RTA received an IGMP report version 1 from host 192.168.9.1.C. Reverse Path Forwarding (RPF) is ena bled for 192.168.9.4.D. Reverse Path Forwarding (RPF) is enabled for 224.0.1.40.E. The IP multicast groups are 224.0.0.1, 224.0.1.40, and 239.255.0.1.F. IP PIM RP mapping is static.
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Refer to the exhibit. IP multicast configuration changes have been made on several routers.However, the IP multicast table displayed in the exhibit still does not reflect the changes. What should be done to display the new routing table information? （）A. Issue the clear ip route * privileged EXEC command.B. Issue the clear ip igmp group privileged EXEC command.C. Issue the no ip mroute - cache privileged EXEC command.D. Issue the clear ip mroute privileged EXEC command.
Refer to the exhibit. What two statements are true?() A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?（）A.VLANs have not been created yetB.An IP address must be configured for the portC.The port is currently configured for access modeD.The correct encapsulation type has not been configuredE.The no shutdown command has not been entered for the port
Typically, an IP address refers to an individual host on a particular network. IP also accommodates addresses that refer to a group of hosts on one or more networks. Such addresses are referred to as multicast addresses, and the act of sending a packet from a source to the members of a （1）group is referred to as multicasting. Multicasting done （2）the scope of a single LAN segment is straightforward. IEEE 802 and other LAN protocols include provision for MAC-level multicast addresses. A packet with a multicast address is transmitted on a LAN Segment. Those stations that are members of the （3）multicast group recognize the multicast address and （4）the packet. In this case, only a single copy of the packet is ever transmitted. This technique works because of the （5）nature of a LAN: A transmission from any one station is received by all other station on the LAN.空白（5）应选（ ）。 A. Multicast B. unicast C. broadcastD. multiple unicast
Typically, an IP address refers to an individual host on a particular network. IP also accommodates addresses that refer to a group of hosts on one or more networks. Such addresses are referred to as multicast addresses, and the act of sending a packet from a source to the members of a （1）group is referred to as multicasting. Multicasting done （2）the scope of a single LAN segment is straightforward. IEEE 802 and other LAN protocols include provision for MAC-level multicast addresses. A packet with a multicast address is transmitted on a LAN Segment. Those stations that are members of the （3）multicast group recognize the multicast address and （4）the packet. In this case, only a single copy of the packet is ever transmitted. This technique works because of the （5）nature of a LAN: A transmission from any one station is received by all other station on the LAN.空白（3）应选（ ）。 A. Different B. unique C. specialD. corresponding
Typically，an IP address refers to an individual host on a particular network. IP also accommodates addresses that refer to a group of hosts on one or more networks.Such addresses are referred to as multicast addresses，and the act of sending a packet from a source to the members of a （71）group is referred to as multicasting. Multicasting done （72） the scope of a single LAN segment is straight forward. IEEE 802 and other LAN protocols include provision for MAC-level multicast addresses. A packet with a multicast address is transmitted on a LAN segment.Those stations that are members of the （73）multicast group recognize the multicast address and （74）the packet.In this case,only a single copy of the packet is ever transmitted.This technique works because of the （本题）nature of a LAN:A transmission from any one station is received by all other stations on the LAN. A .multicastB. unicastC.broadcastD.multiple unicast
What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）A、Route reflectors are not passing updates properly.B、BGP synchronization has been enabled.C、The next-hop address is unreachable.D、No loopback interface has been configured on a router.
Which three IP multicast group concepts are true?（）A、If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.B、A router does not have to be a member of a multicast group to receive multicast data.C、A router must be a member of a multicast group to send to the group.D、A router does not have to be a member of a multicast group to send to the group.E、If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.F、A router must be a member of a multicast group to receive multicast data.
Which three attributes are carried in a source active message?（）A、NLRI informationB、IP address of originating RPC、address of multicast sourceD、all active RPs in the local domainE、group address to which the source is sending
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.B、 When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.E、None of the other answers is correct.
Which three IP multicast group concepts are true?（）A、If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.B、A router does not have to be a member of a multicast group to recei ve multicast data.C、A router must be a member of a multicast group to send to the group.D、A router does not have to be a member of a multicast group to send to the group.E、If a packet is sent to a multicast group address, all members of the multic ast group will receive it.F、A router must be a member of a multicast group to receive multicast data.
Multicast is being deployed in the network， and only ip pim sparse-dense mode has been configured on all interfaces in the network to support a new video streaming application. No other multicast configuration was applied anywhere in the network. Since enabling multicast， the network monitoring tools show periodic spikes in link utilization throughout the network， even in areas where the video application is not being used. What could be a possible cause？（）A、PIM sparse mode is being used.B、PIM dense mode is being used.C、The BGP multicast address family has not been configured.D、IGMP version 3 is being used.E、IP PIM neighbor filters have not been applied.
Which three IP multicast group concepts are true？ （Choose three.） （）A、 If a packet is sent to a multicast group address， all members of the multicast group will receive itB、 If a packet is sent to a multicast group address， the multicast frame contains the source multicast addressC、 A router does not have to be a member of a multicast group to receive multicast data.D、 A router does not have to be a member of a multicast group to send to the group.E、 A router must be a member of a multicast group to receive multicast data.F、 A router must be a member of a multicast group to send to the group.
Which three IP multicast related statements are true？ （Choose three.） （）A、 Multicast addresses 224.0.1.0 through 238.255.255.255 are called globally scoped addresses. They are used to multicast data between organizations and across the InternetB、 The multicast address 224.0.0.1 is a globally scoped address that has been reserved for the Network Time Protocol （NTP） by the IANAC、 Multicast addresses 239.0.0.0 through 239.255.255.255 are called limited scope addresses. They are constrained to a local group or organizationD、 Multicast addresses 224.0.0.5 and 224.0.0.6 are limited scoped addresses that have been reserved for OSPFE、 Multicast addresses 224.0.0.0 through 224.0.0.255 are used for network protocols on local LAN segments. Because they are always transmitted with a Time to Live （TTL） of 1， they are never forwarded by a router
多选题Which three IP multicast group concepts are true？ （Choose three.） （）AIf a packet is sent to a multicast group address， all members of the multicast group will receive itBIf a packet is sent to a multicast group address， the multicast frame contains the source multicast addressCA router does not have to be a member of a multicast group to receive multicast data.DA router does not have to be a member of a multicast group to send to the group.EA router must be a member of a multicast group to receive multicast data.FA router must be a member of a multicast group to send to the group.
多选题Which three IP multicast group concepts are true?（）AIf a packet is sent to a multicast group address, the multicast frame contains the source multicast address.BA router does not have to be a member of a multicast group to receive multicast data.CA router must be a member of a multicast group to send to the group.DA router does not have to be a member of a multicast group to send to the group.EIf a packet is sent to a multicast group address, all members of the multicast group will rece ive it.FA router must be a member of a multicast group to receive multicast data.
多选题Which three IP multicast related statements are true？ （Choose three.） （）AMulticast addresses 224.0.1.0 through 238.255.255.255 are called globally scoped addresses. They are used to multicast data between organizations and across the InternetBThe multicast address 224.0.0.1 is a globally scoped address that has been reserved for the Network Time Protocol （NTP） by the IANACMulticast addresses 239.0.0.0 through 239.255.255.255 are called limited scope addresses. They are constrained to a local group or organizationDMulticast addresses 224.0.0.5 and 224.0.0.6 are limited scoped addresses that have been reserved for OSPFEMulticast addresses 224.0.0.0 through 224.0.0.255 are used for network protocols on local LAN segments. Because they are always transmitted with a Time to Live （TTL） of 1， they are never forwarded by a router
多选题Which three IP multicast group concepts are true?（）AIf a packet is sent to a multicast group address, the multicast frame contains the source multicast address.BA router does not have to be a member of a multicast group to recei ve multicast data.CA router must be a member of a multicast group to send to the group.DA router does not have to be a member of a multicast group to send to the group.EIf a packet is sent to a multicast group address, all members of the multic ast group will receive it.FA router must be a member of a multicast group to receive multicast data.
多选题Refer to the exhibit. A customer indicates their teleworkers plan to use IP phones in their home offices. The IT department has surveyed the planned teleworkers, resulting in the user groupings shown in the exhibit. To provide the highest voice quality, the best recommendations to this customer are（）.ADeploy all three groups with a QoS service policy, choosing the parameters for Traffic Shaping based on the average uplink speed across the three groups.BTeleworkers in Groups A and B should inquire with their DSL providers for subscriptions with higher uplink bandwidths.CTeleworkers in Group C should change their subscriptions to DSL for deployment consistency.DTeleworkers in Group A should upgrade their subscription to obtain static IP addressesETeleworkers in Group A should inquire with their DSL providers for subscriptions with higher downlink bandwidths.
单选题Multicast is being deployed in the network， and only ip pim sparse-dense mode has been configured on all interfaces in the network to support a new video streaming application. No other multicast configuration was applied anywhere in the network. Since enabling multicast， the network monitoring tools show periodic spikes in link utilization throughout the network， even in areas where the video application is not being used. What could be a possible cause？（）APIM sparse mode is being used.BPIM dense mode is being used.CThe BGP multicast address family has not been configured.DIGMP version 3 is being used.EIP PIM neighbor filters have not been applied.
单选题What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）ARoute reflectors are not passing updates properly.BBGP synchronization has been enabled.CThe next-hop address is unreachable.DNo loopback interface has been configured on a router.