Refer to the exhibit, Host A pings interface S0／0 on router 3, what is the TTL value for that ping?() A. 253B. 252C. 255D. 254
Refer to the exhibit, Host A pings interface S0／0 on router 3, what is the TTL value for that ping?()
A. 253
B. 252
C. 255
D. 254
相关考题：
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
Refer to the exhibit. What three statements are true about the IS － IS configuration?() A.The router is in area 49.0001.0002B.The router acts as a Level 1 - 2 routerC.CLNS routing is enable d for the routerD.The router has a system ID of 0003.0004E.The interfaces have a functional IS - IS configurationF.The network service access point selector (NSEL) byte has a value of 0
Refer to the exhibit. What two statements are true?() A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.
Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B?() A.The loopback addresses are on different subnetsB.The value of the dead timers on the router are differentC.Route summarization is enabled on both routersD.The process indentifier on router A is different than the process identifier on router B
Refer to the exhibit.The network administrator normally establishes a telnet session with the switch from host A.However,host A is unavailable.The administrators attempt to the switch from host B fails,but pings to the other two hosts are successful.what is the issue?（）A.Host B and the switch need to be in the same subnet.B.The switch needs and appropriate default gateway assigned.C.The switch interface connected to the router is down.D.Host B need to be assigned an IP address in vlan 1.E.The switch interfaces need the appropriate IP addresses assigned.
Refer to the graphic.Host A is communicating with the seiver. What will be the source MAC address of the frames received by Host A from the server?() A.the MAC address of the seiver network interfaceB.the MAC address of host AC.the MAC address of router interface e 1D.the MAC address of router interface e0
The user of Host1 wants to ping the DSL modem／router at 192.168.1.254. Based on the Host1 ARP table that is shown in the exhibit, what will Host1 do()。 A.send a unicast ARP packet to the DSL modem/routerB.send unicast ICMP packets to the DSL modem/routerC.send Layer 3 broadcast packets to which the DSL modem/router respondsD.send a Layer 2 broadcast that is received by Host2, the switch, and the DSL modem/router
Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。A、The Mac address of the NIC in Sever1B、The IP address of Server 1.C、The MAC address of the s0/0/0 interface of router R2D、The IP address of the s0/0/0 interface of router R1E、The IP address of the Fa0/0 interface of router R1
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below: Gateway of last resort is 10.1.2.2 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0 C 10.1.2.0 is directly connected, Serial0/0 C 10.1.5.0 is directly connected, Serial0/1 C 10.1.6.0 is directly connected, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1 Based on the output above, if an administrator pings host 10.1.8.5 from host 10.1.6.100, how will the router TestkingA process the ICMP packets?（）A、The packets will be discarded.B、The packets will be routed out the S0/0 interface.C、The packets will be routed out the S0/1 interface.D、The packets will be routed out the Fa0/0 interface.E、The packets will be routed through the 10.1.2.2 gateway.
Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1（）。A、The MAC address of the NIC in Host 1B、The MAC address of the NIC in server 1C、The MAC address of the Fa0/0 interface of router R1D、The MAC address of the s0/0/0 interface of the router R2
Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）A、HostA is not on the same subnet as its default gatewayB、The address of SwitchA is a subnet addressC、The Fa0/0 interface on RouterA is on a subnet that cannot be usedD、The serial interfaces of the routers are not on the same subnetE、The Fa0/0 interface on RouterB is using a broadcast address
Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。A、The IP address of sever 1.B、The MAC address of NIC in sever 1.C、The IP address of F0/0 interface of router R1.D、The MAC address of the Fa0/0 interface of router R1.E、The IP address of the s0/0/0 interface of router R2F、The MAC address of the s0/0/0 interface of router R2
You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall commandB、The count parameter allows the router to count the number of pings for logging purposesC、The count parameter allows the router to pause for 10000 seconds before sending out a pingD、The count parameter allows the router to send out 1000 pings and then stop
You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall command.B、The count parameter allows the router to count the number of pings for logging purposes.C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.D、The count parameter allows the router to send out 1000 pings and then stop.
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A、The Popcorn router is not forwarding RIP updates.B、The Popcorn router did not include network 192.168.12.0 in its routing configuration.C、The Ethernet1 interface of the Popcorn router is shutdown.D、The clockrate is not present in the configuration of one of the routers.E、The Serial interface of the Popcorn router is not operating.
Which three route filtering statements are true?（）A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Examine the following configuration on Router R1. R1's show ip route 172.16.4.1 command list s a route with outgoing interface S0/1/1. Host 172.16.3.3 uses telnet to connect to host 172.16.4.1.What will Router R1 do with the packets generated by host 172.16.3.3 because of the telnet,assuming the packets enter R1's F0/0 interface?（） interface Fastethernet 0/0 ip address 172.16.1.1 255.255.255.0 ip policy route - map Q2 ! route - map Q2 permit match ip address 101 set interface s0/0/1 ! access - list 101 permit tcp host 172.16.3.3 172.16.4.0 0.0.0.255A、The packet will be forwarded out S0/0 /1, or not at all.B、The packet will be forwarded out S0/0/1 if it is up.C、The packet will be forwarded out S0/1/1 if it is up.D、The packet will be forwarded out S0/1/1 if it is up, or if it is not up, out s0/0/1.E、The packet will be forwarded o ut S0/0/1 if it is up, or if it is not up, out s0/1/1.
单选题Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。AThe Mac address of the NIC in Sever1BThe IP address of Server 1.CThe MAC address of the s0/0/0 interface of router R2DThe IP address of the s0/0/0 interface of router R1EThe IP address of the Fa0/0 interface of router R1
单选题Refer to the exhibit.The network administrator normally establishes a telnet session with the switch from host A.However,host A is unavailable.The administrator′s attempt to the switch from host B fails,but pings to the other two hosts are successful.what is the issue?（）A Host B and the switch need to be in the same subnet.B The switch needs and appropriate default gateway assigned.C The switch interface connected to the router is down.D Host B need to be assigned an IP address in vlan 1.E The switch interfaces need the appropriate IP addresses assigned.
单选题The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below: Gateway of last resort is 10.1.2.2 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0 C 10.1.2.0 is directly connected, Serial0/0 C 10.1.5.0 is directly connected, Serial0/1 C 10.1.6.0 is directly connected, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1 Based on the output above, if an administrator pings host 10.1.8.5 from host 10.1.6.100, how will the router TestkingA process the ICMP packets?（）AThe packets will be discarded.BThe packets will be routed out the S0/0 interface.CThe packets will be routed out the S0/1 interface.DThe packets will be routed out the Fa0/0 interface.EThe packets will be routed through the 10.1.2.2 gateway.
单选题Host 1 receives a file from remote server 1. Which MAC address appears as the source address in the header of the frames received by Host 1（）。AThe MAC address of the NIC in Host 1BThe MAC address of the NIC in server 1CThe MAC address of the Fa0/0 interface of router R1DThe MAC address of the s0/0/0 interface of the router R2
单选题You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）AThe count parameter creates a counter that you can view with the show firewall command.BThe count parameter allows the router to count the number of pings for logging purposes.CThe count parameter allows the router to pause for 1000 seconds before sending out a ping.DThe count parameter allows the router to send out 1000 pings and then stop.
多选题The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）AThe Popcorn router is not forwarding RIP updates.BThe Popcorn router did not include network 192.168.12.0 in its routing configuration.CThe Ethernet1 interface of the Popcorn router is shutdown.DThe clockrate is not present in the configuration of one of the routers.EThe Serial interface of the Popcorn router is not operating.
多选题Refer to the exhibit. On the basis of the information in the exhibit， which two statements are true？（）AWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2BThe serial 0/0/1 interface on the ISP router has been configured with the set metric 50commandCThe output was generated by entering the show ip bgp command on the SanJose1 routerDThe output was generated by entering the show ip bgp command on the ISP routerEThe serial 0/0/1 interface on the ISP router has been configured with the set metric 75commandFWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
单选题Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。AThe IP address of sever 1.BThe MAC address of NIC in sever 1.CThe IP address of F0/0 interface of router R1.DThe MAC address of the Fa0/0 interface of router R1.EThe IP address of the s0/0/0 interface of router R2FThe MAC address of the s0/0/0 interface of router R2
单选题Refer to the exhibit.HostA cannot ping HostB.Assuming routing is properly configured,what could be the cause of this problem?（）AHostA is not on the same subnet as its default gatewayBThe address of SwitchA is a subnet addressCThe Fa0/0 interface on RouterA is on a subnet that cannot be usedDThe serial interfaces of the routers are not on the same subnetEThe Fa0/0 interface on RouterB is using a broadcast address