Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）A、frame - relay map commands on R3 - R10 referencing the other routers in this groupB、Nine OSPF neighbor commands on each routerC、Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10D、R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRE、R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）
- A、frame - relay map commands on R3 - R10 referencing the other routers in this group
- B、Nine OSPF neighbor commands on each router
- C、Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10
- D、R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDR
- E、R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
相关考题：
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）A. PrivacyB. AuthenticationC. Allows using an IGP between R1 and the EnterpriseD. Secure communications
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Given the network diagram, which routers currently make up the IS － IS backbone?() A. R3,R4,R6B. R2,R3,R6,R7C. R1 through R8D. R3,R4,R5,R6E. R2,R3,R4,R6,R7
Refer to the exhibit. In a redundant hub - and - spoke deployment using EIGRP, what feature can be used to ensure that routers C through F are not used as transit routers for data traveling from router B to network 10.1.1.0? Select the best response.（）A. Use address summarization at routers C, D, E, and FB. Use the EIGRP Stub featu re on routers C, D, E, and FC. Use passive - interface on the spoke links in routers A and BD. Change the administrative distance in routers A and B for routes learned from routers C, D, E,and F
Refer to the e xhibit. It is desired to set up a BGP neighbor relationship between routers R1 and R4. BGP packets between them could travel through R2 or R3. What is the simplest configuration that will allow for failover?（）A. Configure BGP n eighbor relationships between all interfaces on R1 and R4.B. Install a direct connection between R1 and R4.C. Configure loopback interfaces on R1 and R4 to provide the update source address for BGP packets.D. Configure only one neighbor relationship between R1‘s 192.168.1.2 interface and R4‘s 172.16.10.2 interface.
Refer to the exhibit. Routers R1 and R2 have been configured to operate with OSPF. Routers R1 and R3 have been configured to operate with RIP. After configuring the redistribution between OSPF a nd RIP on R1, no OSPF routes are distributed into RIP. What should be done to correct this problem? （）A. The redistribution command should be reentered with the match route - type parameter included.B. The redistribution command should be reentered wit h the route - map map - tag parameter included.C. The redistribution command should be reentered with the metric metric - value parameter included.D. Routes will first need to be distributed into another protocol, and then into RIP.
Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）A. both routers R1 and R2B. router R1C. router R2D. none of the routers since they are not configured with static RP
Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）A. The OSPF area is not configured properly.B. The priority on R1 should be set higher.C. The cost on R1 should be set higher.D. The hello and dead timers are not configured properly.E. A backup designated router needs to be added to the network.F. The OSPF process ID numbers must match.
A:Something important has come up.（） B:Can it wait? I’ll be through in ten minutes.ACanyouspareaminute?BCanitwait?CSorrytointerrupt.DDoyoumind?
A:Something important has come up.（） B:Can it wait? I’ll be through in ten minutes.A、Canyouspareaminute?B、Canitwait?C、Sorrytointerrupt.D、Doyoumind?
Routers R1 and R2 are EIGRP neighbors. R1 has been configured with the eigrp stub connected command. Which of the following is true as a result？（）A、R1 can learn EIGRP routes from R2, but R2 cannot learn EIGRP routes from R1B、R1 can send IP packets to R2, but R2 cannot send IP packets to R1C、R2 no longer learns EIGRP routes from R1 for routes not connected to R1D、R1 no longer replies to R2's Query messagesE、R2n o longer sends to R1 Query messages
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers. B、 Routers configured for HSRP can belong to multiple groups and multiple VLANs.C、 Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.D、 All routers configured for HSRP load balancing must be configured with the same priority. E、 Routers configured for HSRP must belong to only one group per HSRP interface.
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）A、The show ip eigrp neighbors command on R1 lists the revised Hello timerB、The show ip eigrp interfaces command on R1 lists the revised Hello timerC、The R1 - R2 neighborship fails due to Hello timer mismatcHD、The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Router R1 sits inside OSPF area 1. Router R2 redistributes an E1 route into OSPF for prefix 2.2.2.0/24, with external metric 20. Router R22 redistributes an E2 route for the same prefix/length, external metric 10. Under what conditions will R1 choose as it s best route the route through R22?（）A、R1 will always choose the route through R22.B、As long as R1's best internal OSPF cost to reach R22 is less than 10.C、As long as R1's best internal OSPF cost to reach R22 is less than 20.D、R1 will never choo se the route through R22 if the E1 route through R2 is available.
R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）A、 LearnB、 SpeakC、 StandbyD、 ListenE、 ActiveF、 Remove
Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）A、The show ip ospf neighbors command lists two neighbors off Fa0/0.B、The show ip ospf neighbors command lists four neighbors off Fa0/0.C、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.D、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
单选题Router R1 sits inside OSPF area 1. Router R2 redistributes an E1 route into OSPF for prefix 2.2.2.0/24, with external metric 20. Router R22 redistributes an E2 route for the same prefix/length, external metric 10. Under what conditions will R1 choose as it s best route the route through R22?（）AR1 will always choose the route through R22.BAs long as R1's best internal OSPF cost to reach R22 is less than 10.CAs long as R1's best internal OSPF cost to reach R22 is less than 20.DR1 will never choo se the route through R22 if the E1 route through R2 is available.
单选题Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE. Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）APrivacyBAuthenticationCAllows using an IGP between R1 and the EnterpriseDSecure communications
单选题Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）ATraffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.BR2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.CR2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.DAll the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
多选题Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts. Which commands are required for proper functioning of OSPF in this case?（）Aframe - relay map commands on R3 - R10 referencing the other routers in this groupBNine OSPF neighbor commands on each routerCNine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10DR1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDRER3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
单选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at the ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. Assuming as many default s ettings as possible are used on all four routers, which of the following is true about the next - hop IP address for routes R1 learns over its iBGP connection to R2?（）AThe next hop is I2's BGP RIDBThe next hop is I2's IP address used on the R2 - I2 neigh bor relationshipCThe next hop is R2's BGP RIDDThe next hop is R2's IP address used on the R1 - R2 neighbor relationship
多选题What are two benefits of the Cisco 1800 Series Integrated Services Routers？（）Afixed configuration for secure broadband， metro Ethernet， and wireless connectivityBconfiguration for security policy monitoringCdynamic management through self-healing processesDconnectivity options and investment protection through support for existing Cisco 1700 SeriesWICs
多选题A company uses Routers R1 and R2 to connect to ISP1 and ISP2, respectively, with Routers I1 and I2 used at th e ISPs. R1 peers with I1 and R2; R2 peers with I2 and R1. R1 and R2 do not share a common subnet, relying on other routers internal to the Enterprise for IP connectivity between the two routers. Which of the following could be used to prevent potential routing loops in this design?（）AUsing an iBGP mesh inside the Enterprise coreBConfiguring default routes in the Enterprise pointing to both R1 and R2CRedistributing BGP routes into the Enterprise IGPDTunneling the packets for the i BGP connection between R1 and R2
多选题R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）ALearnBSpeakCStandbyDListenEActiveFRemove
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24
单选题Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration. Which of the following is true regarding the results from this c hange？（）AThe show ip eigrp neighbors command on R1 lists the revised Hello timerBThe show ip eigrp interfaces command on R1 lists the revised Hello timerCThe R1 - R2 neighborship fails due to Hello timer mismatcHDThe show ip eigrp interfaces detail command on R1 lists the revised Hello timer