配置数据业务pon vlan 1000，要求为CC模式，带单tag，如何配置参数？ENT-PONVLAN::PONVLAN-1000::::MODE=（）,NAME=VLAN1000,DHCPRELAY=DISABLED,TAGMODE=（）,PPPOERELAY=DISABLED;
配置数据业务pon vlan 1000，要求为CC模式，带单tag，如何配置参数？ ENT-PONVLAN::PONVLAN-1000::::MODE=（）,NAME=VLAN1000,DHCPRELAY=DISABLED,TAGMODE=（）,PPPOERELAY=DISABLED;
相关考题：
● 新交换机出厂时的默认配置是 （58） 。（58）A. 预配置为VLAN 1，VTP 模式为服务器B. 预配置为VLAN 1，VTP 模式为客户机C. 预配置为VLAN 0，VTP 模式为服务器D. 预配置为VLAN 0，VTP 模式为客户机
下列关于命令配置模式的叙述正确的为 A.向VLAN中增加端口的配置命令模式是全局模式B.添加VLAN的配置命令模式为全局配置模式C.设置端口PVID的配置命令模式为以太网接口配置模式D.设置相应的端口链路为干道链路的配置命令模式为以太网接口模式
阅读以下配置信息，解释(5)、(6)空缺处的命令的功能。SW1 configtSW1(config) interface f0/1 (进入接口1配置模式)SW1(config-if)switchport mode trunk ((5))SW1(config-if)switchpont runk allowed vlan all(设置允许从该接口交换数据的vlan)SW1(config-if) endSW1 vlan dSW1(vlan) vlan 2 (创建一个vlan 2)VLAN 2 addedName：VLAN0002 (系统自动命名)SW1(vlan) vlan 3 name vlan3 ((6))VLAN 3 added：Name：vlan3SW1(vlan)exit
阅读下面的配置信息，将(1)～(4)处空缺的内容填写在相应位置。SW1＞enable (进入特权模式)SW1vlan database (进入VLAN配置子模式)SW1(vlan)vtp server (设置本交换机为Server模式)SW1(vlan)vtp domain (1) (设置域名)SW1(vlan) (2) (启动修剪功能)SW1(vlan)exit (退出VLAN配置模式)SW1show (3) (查看VTP设置信息)VTP Vetsion :2Configuration Revision :0Maximum VLANs supported locrlly :64Number of existing VLANs :1VTP Operating Mode :ServerVTP Domain Name :Server1VTP Pruning Mode :EnableVTP V2 Mode :DisabledVTP Traps Generation :DisabledMD5 digest :0x82 0x6B 0xFB 0x94 0x41 0xEF 0x92 0x30Configuration last modified by 0.0.0.0 at 7-1-05 00:07:51SW2vlan databaseSW2(vlan)vtp domain NULLSW2(vlan) (4)Setting device to VTP CLIENT mode.SW2(vlan)exit
下列关于命令配置模式的叙述有误的为()。 A.添加VLAN的配置命令模式为全局配置模式B.设置端口PVID的配置命令模式为接口配置模式C.设置相应的端口链路为Trunk链路的配置命令模式为接口模式D.向VLAN中增加端口的配置命令模式是全局模式
资源自动配置时，卡单或自动配置失败，报“未找到可配置的业务VLAN资源”错的原因。（）A、业务VLAN未关联OLT设备的PON口B、语音VLAN下没生成语音虚拟VLANC、没在语音虚拟VLAN下绑定语音IP地址D、各业务VLAN值录入错误
下列关于命令配置模式的叙述有误的为（）。A、添加VLAN的配置命令模式为全局配置模式B、设置端口PVID的配置命令模式为接口配置模式C、设置相应的端口链路为Trunk链路的配置命令模式为接口模式D、向VLAN中增加端口的配置命令模式是全局模式
Nexus# sh ip igmp snooping vlan 120 IGMP Snooping information for vlan 120 IGMP snooping disabled Optimised Multicast Flood （OMF） disabled IGMP querier none Switch-querier enabled， address 1.1.1.1， currently not running IGMPv3 Explicit tracking enabled IGMPv2 Fast leave disabled IGMPv1/v2 Report suppression enabled IGMPv3 Report suppression disabled Link Local Groups suppression enabled Router port detection using PIM Hellos， IGMP Queries Number of router-ports： 0 Number of groups： 0 Active ports： Po100 Po111 Which statement best describes what is depicted in the show command output？（）A、 IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.B、 The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.C、 IGMP snooping has been disabled on the VLAN 120 SVI.D、 IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.E、 IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
交换机如何将接口设置为TAG VLAN模式？（）A、switchport mode tagB、switchport mode trunkC、trunk onD、set port trunk on
在EPON应用中，如果用户端的家庭网关或者交换机是运营商提供并统一进行VLAN管理的，那么在UNI端口上VLAN操作模式应该配置为（）。A、VLAN标记模式B、VLAN透传模式C、VLAN Translation模式D、VLAN Tag模式
7342配置专线业务，要求为RB模式，vlan 透传，由于管理VLAN=3000采用RB VLAN模式，而RB VLAN的下行广播包被抑制，为了保证管理的畅通，因此在VLAN=3000中配置了DHCP Relay和静态IP？ ENT-PONVLAN::PONVLAN-3000::::MODE=（）,NAME=VLAN3000,DHCPRELAY=（）,TAGMODE=（）,PPPOERELAY=DISABLED; ENT-（）::PONVLAN-3000:::218.10.180.171,BRGPORT-1-1-1-1-1-1-2:CVLAN=0;
7342 EPON OLT在配置24240ONU的管理VLAN,其中FDBTYPE必须设置成哪种模式 ENT-PONVLAN::PONVLAN-353::::MODE=RBRIDGE,FDBTYPE=（） ,TAGMODE=UNSTACKED；
配置MARK profile要求为Flexible provisioning mode，下行流带tag，参数如何配置？ENT-QOS-MARKPROF::15:::mark（）trans:PROFTYPE=（）,DOT1P=0,UNTAGDS=（）,UNTAGUS=DROP;
配置数据业务pon vlan 1000，要求为RB模式，带双层tag，如何配置参数？ENT-PONVLAN::PONVLAN-1000::::MODE=（）,NAME=VLAN1000,DHCPRELAY=DISABLED,TAGMODE=（）,PPPOERELAY=DISABLED;
GPRS/EDGE网络有3种运作模式：MODEⅠ、MODEⅡ和MODEⅢ。以下说法正确的是（）A、MODEⅠ可以选择是否配置MPDCH，MODEⅡ不能配置MPDCH，MODEⅢ一定要配置MPDCH；B、MODEⅠ必须配置MPDCH；MODEⅡ可以选择是否配置MPDCH，MODEⅢ不能配置MPDCH；C、MODEⅠ不能配置MPDCH；MODEⅡ必须配置MPDCH；MODEⅢ可以选择是否配置MPDCH；D、无论何种MODE，均可以不配置FPDCH；
有关ONU端口VLAN模式设置的说法正确的有（）。A、如果ONU直接接电脑或UNTAG上行的以太网交换机，可以配置成TAg模式，将PVID设定成与C200中配置的业务VLAN一致B、如果ONU接TAG上行的以太网交换机，交换机的VLAN信息需要上传，可以配置成透传模式。C、如果ONU接TAG上行的以太网交换机，交换机的VLAN信息需要上传，可以配置成TAg模式，将PVID设定成与交换机上任意VLAN一致。D、如果ONU直接接电脑或UNTAG上行的以太网交换机，一般情况下我们会将端口设置成交换模式，将VLAN都交换到VLAN1中转发
Which statement best describes what is depicted in the show command output？（）A、 IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.B、 The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.C、 IGMP snooping has been disabled on the VLAN 120 SVI.D、 IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.E、 IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
单选题Nexus# sh ip igmp snooping vlan 120 IGMP Snooping information for vlan 120 IGMP snooping disabled Optimised Multicast Flood （OMF） disabled IGMP querier none Switch-querier enabled， address 1.1.1.1， currently not running IGMPv3 Explicit tracking enabled IGMPv2 Fast leave disabled IGMPv1/v2 Report suppression enabled IGMPv3 Report suppression disabled Link Local Groups suppression enabled Router port detection using PIM Hellos， IGMP Queries Number of router-ports： 0 Number of groups： 0 Active ports： Po100 Po111 Which statement best describes what is depicted in the show command output？（）A IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.B The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.C IGMP snooping has been disabled on the VLAN 120 SVI.D IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.E IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.
单选题Which statement best describes what is depicted in the show command output？（）A IGMP snooping is not active for VLAN 120 because the IGMP feature has not been enabled on the switch with the feature igmp command.B The IGMP snooping querier for VLAN 120 is not in a running state because the Loopback interface configured with 1.1.1.1/32 is currently in a down state.C IGMP snooping has been disabled on the VLAN 120 SVI.D IGMP snooping has been disabled for VLAN 120 in VLAN configuration mode.E IGMP snooping is not active for VLAN 120 because VLAN 120 does not exist in the VLAN database.