单选题A defective CD-ROM drive is replaced with a new CD-ROM drive. The new CD-ROM drive is able to read any CD that it accesses， but music CDs do not play music. What is the MOST likely cause of this problem？（）AThe audio cable is not connected to the drive.BThe ribbon cable is not connected.CThe power cable is not connected.DThe CD-ROM drivers are not installed.
单选题
A defective CD-ROM drive is replaced with a new CD-ROM drive. The new CD-ROM drive is able to read any CD that it accesses， but music CDs do not play music. What is the MOST likely cause of this problem？（）
A
The audio cable is not connected to the drive.
B
The ribbon cable is not connected.
C
The power cable is not connected.
D
The CD-ROM drivers are not installed.
参考解析
解析：
暂无解析
相关考题：
A technician replaced a floppy drive and now the front indicator light is consistently illuminated.Which of the following is the cause for this?() A. It is a feature of new floppy drives.B. The data cable was put on backwards.C. A disk is being read by the floppy drive.D. The new floppy drive is defective.
A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller.Which of the following is the MOST likely cause of the problem?（）A. Both hard drives have the master jumper in place.B. One hard drive is set as master and the other slave.C. The hard drive data cable is reversed.D. Both hard drives have the cable select jumper in place.
A customer receives a CD-RW disk from a computer vendor. The customer tries to read the disk in a computer with a 4X CD-ROM drive and is unable to read any information. The customer tries the CD-RW disk on a 32X CD-ROM drive and it reads correctly. What is the cause of this problem？（）A、The 4X CD-ROM drive has dirty optics or laser and requires cleaning.B、The 4X CD-ROM drive needs to be jumpered to support CD-RW disks.C、The 4X CD-ROM drive does not support the multi-read specification.D、The 4X CD-ROM is fine， but the CD-RW disk has a flaw in its format.
A user reports that after configuring the BIOS to boot to the hard drive first, the system still tries to boot from the optical drive. Which of the following is the MOST likely cause?（）A、Optical driveB、Power supplyC、CMOS batteryD、CD-ROM disk
A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）A、Both hard drives have the master jumper in place.B、One hard drive is set as master and the other slave.C、The hard drive data cable is reversed.D、Both hard drives have the cable select jumper in place.
A technician replaced a floppy drive and now the front indicator light is consistently illuminated.Which of the following is the cause for this?（）A、It is a feature of new floppy drives.B、The data cable was put on backwards.C、A disk is being read by the floppy drive.D、The new floppy drive is defective.
A user is trying to boot a desktop PC from their A: drive. Which of the following devices is the userdescribing？（）A、The floppy driveB、The hard driveC、The CD-ROM driveD、The DVD-ROM drive
A computer has been upgraded with a new hard drive and after reassembling the computer and turning the computer on， the drive LED remains lit and an error message during power-on self test （POST） states， ’No Drive Present.’ Which of the following would MOST likely be the cause？（）A、The motherboard was damaged and needs replacing.B、The floppy drive was not reconnected.C、A configuration disk was left in the floppy drive.D、The ribbon cable has been installed incorrectly.
After POST, the error message ‘Invalid system disk. Replace and press any key’ appears. Which of the following is MOST likely the cause?（）A、There is a non-bootable CD in the CD-ROM drive.B、There is a non-bootable DVD in the DVD-ROM drive.C、There is a non-bootable Blu-Ray in the Blu-Ray drive.D、There is a non-bootable floppy in the floppy drive.
Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）A、The new drive’s jumper is set for master.B、The new drive is connected to the secondary bus as a slave drive.C、Both drives’ jumpers are set for cable select.D、The old drive’s jumper is set for master and the new drive is set for slave.
A floppy drive is replaced in a computer and now when the computer is turned on the floppy drive light is constantly lit. Which of the following is the MOST likely cause?（）A、The power supply has failed.B、The drive cable is connected backwards.C、The floppy drive has failed.D、The proper drivers have not been loaded.
A user has recently added a second IDE CD-RW drive to a machine in addition to the primary DVD-ROM drive. The drive opens and closes; however, they do not see it show up in Windows. Which of the following is the MOST likely cause?（）A、The drive jumper settings are incorrect.B、The drive is not receiving power from PSU.C、Windows only supports one optical drive.D、The user connected the drive with a SATA cable.
A defective CD-ROM drive is replaced with a new CD-ROM drive. The new CD-ROM drive is able to read any CD that it accesses， but music CDs do not play music. What is the MOST likely cause of this problem？（）A、The audio cable is not connected to the drive.B、The ribbon cable is not connected.C、The power cable is not connected.D、The CD-ROM drivers are not installed.
A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）A、Windows cannot be booted from a controller card.B、The hard drive must have Windows reinstalled because a new controller card was installed.C、The SATA controller card was not set as a boot device in the computer BIOS.D、The new controller must have the correct jumper settings for Windows mode.
An A+ Certified Technician MUST do an install on a Windows XP system from the distribution CD. However， the system does not boot from this CD. What is the MOST likely cause of this problem？（）A、The CD is defective.B、The CD is not bootable.C、The CD-ROM drive is defective.D、The Boot Sequence is not set in the BIOS to boot first from the CD
单选题A computer has been upgraded with a new hard drive and after reassembling the computer and turning the computer on， the drive LED remains lit and an error message during power-on self test （POST） states， ’No Drive Present.’ Which of the following would MOST likely be the cause？（）AThe motherboard was damaged and needs replacing.BThe floppy drive was not reconnected.CA configuration disk was left in the floppy drive.DThe ribbon cable has been installed incorrectly.
单选题A floppy drive is replaced in a computer and now when the computer is turned on the floppy drive light is constantly lit. Which of the following is the MOST likely cause?（）AThe power supply has failed.BThe drive cable is connected backwards.CThe floppy drive has failed.DThe proper drivers have not been loaded.
单选题A technician replaced a floppy drive and now the front indicator light is consistently illuminated.Which of the following is the cause for this?（）AIt is a feature of new floppy drives.BThe data cable was put on backwards.CA disk is being read by the floppy drive.DThe new floppy drive is defective.
单选题Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）AThe new drive’s jumper is set for master.BThe new drive is connected to the secondary bus as a slave drive.CBoth drives’ jumpers are set for cable select.DThe old drive’s jumper is set for master and the new drive is set for slave.
单选题A user has recently added a second IDE CD-RW drive to a machine in addition to the primary DVD-ROM drive. The drive opens and closes; however, they do not see it show up in Windows. Which of the following is the MOST likely cause?（）AThe drive jumper settings are incorrect.BThe drive is not receiving power from PSU.CWindows only supports one optical drive.DThe user connected the drive with a SATA cable.
单选题A customer receives a CD-RW disk from a computer vendor. The customer tries to read the disk in a computer with a 4X CD-ROM drive and is unable to read any information. The customer tries the CD-RW disk on a 32X CD-ROM drive and it reads correctly. What is the cause of this problem？（）AThe 4X CD-ROM drive has dirty optics or laser and requires cleaning.BThe 4X CD-ROM drive needs to be jumpered to support CD-RW disks.CThe 4X CD-ROM drive does not support the multi-read specification.DThe 4X CD-ROM is fine， but the CD-RW disk has a flaw in its format.
单选题An A+ Certified Technician MUST do an install on a Windows XP system from the distribution CD. However， the system does not boot from this CD. What is the MOST likely cause of this problem？（）AThe CD is defective.BThe CD is not bootable.CThe CD-ROM drive is defective.DThe Boot Sequence is not set in the BIOS to boot first from the CD
单选题A defective CD-ROM drive is replaced with a new CD-ROM drive. The new CD-ROM drive is able to read any CD that it accesses， but music CDs do not play music. What is the MOST likely cause of this problem？（）AThe audio cable is not connected to the drive.BThe ribbon cable is not connected.CThe power cable is not connected.DThe CD-ROM drivers are not installed.
单选题A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）AWindows cannot be booted from a controller card.BThe hard drive must have Windows reinstalled because a new controller card was installed.CThe SATA controller card was not set as a boot device in the computer BIOS.DThe new controller must have the correct jumper settings for Windows mode.
单选题A user is trying to boot a desktop PC from their A: drive. Which of the following devices is the userdescribing？（）AThe floppy driveBThe hard driveCThe CD-ROM driveDThe DVD-ROM drive
单选题After POST, the error message ‘Invalid system disk. Replace and press any key’ appears. Which of the following is MOST likely the cause?（）AThere is a non-bootable CD in the CD-ROM drive.BThere is a non-bootable DVD in the DVD-ROM drive.CThere is a non-bootable Blu-Ray in the Blu-Ray drive.DThere is a non-bootable floppy in the floppy drive.
单选题A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）ABoth hard drives have the master jumper in place.BOne hard drive is set as master and the other slave.CThe hard drive data cable is reversed.DBoth hard drives have the cable select jumper in place.
单选题The technician is working on a system and has determined that the hard drive must be reimaged. However, the customer wants to retain all the data. Which of the following would take the LEAST amount of time to implement?（）ACreate a new partition on the hard drive, copy all data to the new partition, reimage the drive, and the old data will be on the new partition and accessible.BInstall a new hard drive, slave the old drive, image the new drive, and show the customer how to access their data on the old drive.CUpload the data to an external FTP server, reimage the drive, and then restore the data to the newly imaged drive.DCopy data to a USB connected hard drive, reimage the drive, and then restore the data to the newly imaged drive.