单选题Which of the following commands should be used to display a system routing table?（）A route B netstat C iptrace D traceroute
单选题
Which of the following commands should be used to display a system routing table?（）
A
route
B
netstat
C
iptrace
D
traceroute
参考解析
解析：
暂无解析
相关考题：
Which of the following statements regarding EIGRP successor routes is valid?() A. A successor route is used by EIGRP to forward traffic to destination.B. Successor routes are saved in the topology table to be used if the primary route fails.C. Successor routes are flagged as active in the routing table.D. A successor route may be backed up by a feasible successor route.E. Successor routes are stored in the neighbor table following the discovery process.
Which of the following statements regarding EIGRP successor routes is valid?（）A、A successor route is used by EIGRP to forward traffic to destination.B、Successor routes are saved in the topology table to be used if the primary route fails.C、Successor routes are flagged as "active" in the routing table.D、A successor route may be backed up by a feasible successor route.E、Successor routes are stored in the neighbor table following the discovery process.
An administrator needs to review the open ports on a host. Which of the following commands should they use？（）A、traceroute -dB、ping -tC、netstat -anoD、nbtstat -a
Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）A、chrootB、route staticC、route addD、smitty route
Which of the following commands should be used to alter the routing table on a running system without affecting the ODM settings？（）A、inetdB、routeC、cfgmgrD、chdev
Which of the following commands is used to display detailed ethernet statistics for ent0？（）A、 ifconfig ent0B、 entstat -d ent0C、 netstat -iD、 lscfg -vl ent0
Which of the following commands should be used to identify packet sequence problems？（）A、 ping and arpB、 lsattr and ifconfigC、 netstat and iostatD、 iptrace and tcpdump
Which of the following WLM commands should be used to monitor performance on a system running wlm？（）A、 wlmcntrlB、 wlmstatC、 wlmcheckD、 wlmassign
After the LED display is flashing 888 and the system is rebooted, which of the following commands should be used to gather dump information?（）A、snap B、errpt C、kdb D、trace
Which of the following commands is used to determine the route that the IP packets take to a network host?（）A、 route B、 netstat C、 iptrace D、 traceroute
Which of the following commands is used to observe the current state of the routing table？（）A、routeB、lsattrC、netstatD、ifconfig
Which of the following commands gathers network packet statistics？（）A、netstat -iB、ifconfig -aC、errpt -aD、iptrace -i
Which of the following commands should be used to report statistics on network protocols used by the system？（）A、 lsattrB、 pstatC、 netstatD、 ifconfig
Which of the following commands should be used to display a system routing table?（）A、 route B、 netstat C、 iptrace D、 traceroute
What is the role of route preference?（）A、It is used to determine which route should become active.B、It is used to select which routing table to use for forwarding.C、It is used to determine what routes to accept into the routing table.D、It is used to select the best route between multiple equal cost paths.
单选题Which of the following commands should be used to alter the routing table on a running system without affecting the ODM settings？（）AinetdBrouteCcfgmgrDchdev
单选题Which of the following commands should be used to list all of the active network interfaces on a system？（）AlscfgBrouteCnetstatDentstat
单选题What is the role of route preference?（）AIt is used to determine which route should become active.BIt is used to select which routing table to use for forwarding.CIt is used to determine what routes to accept into the routing table.DIt is used to select the best route between multiple equal cost paths.
单选题Which of the following commands is used to observe the current state of the routing table？（）ArouteBlsattrCnetstatDifconfig
单选题Which of the following commands should be used to identify packet sequence problems？（）A ping and arpB lsattr and ifconfigC netstat and iostatD iptrace and tcpdump
单选题After the LED display is flashing 888 and the system is rebooted, which of the following commands should be used to gather dump information?（）Asnap Berrpt Ckdb Dtrace
单选题Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）AchrootBroute staticCroute addDsmitty route
多选题Which of the following statements regarding EIGRP successor routes is valid?（）AA successor route is used by EIGRP to forward traffic to destination.BSuccessor routes are saved in the topology table to be used if the primary route fails.CSuccessor routes are flagged as active in the routing table.DA successor route may be backed up by a feasible successor route.ESuccessor routes are stored in the neighbor table following the discovery process.
多选题You are troubleshooting a routing issue and need to check the hop-by-hop path to the 10.10.10.10 destination. Which three commands would display the path?（）Auser@router# traceroute 10.10.10.10Buser@router ping record-route 10.10.10.10Cuser@routertraceroute 10.10.10.10Duser@router# run traceroute 10.10.10.10Euser@router# ping record-route 10.10.10.10
单选题Which of the following WLM commands should be used to monitor performance on a system running wlm？（）A wlmcntrlB wlmstatC wlmcheckD wlmassign
单选题Which of the following commands should be used to display a system routing table?（）A route B netstat C iptrace D traceroute
单选题Which of the following commands should be used to report statistics on network protocols used by the system？（）A lsattrB pstatC netstatD ifconfig
单选题Which of the following commands is used to determine the route that the IP packets take to a network host?（）A route B netstat C iptrace D traceroute