单选题Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）AchrootBroute staticCroute addDsmitty route
单选题
Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）
A
chroot
B
route static
C
route add
D
smitty route
参考解析
解析：
暂无解析
相关考题：
You have just configured a static default route on router TK1. What is the purpose of a default route?() A. It is a route to be used when the routing protocol fails.B. It is a route configured by an ISP that sends traffic into a corporate network.C. It is a route used when a packet is destined for a remote network that is not listed in the routing table.D. It is a route manually configured for a specific remote network for which a routing protocol is not configured.E. It is used to send traffic to a stub network.
The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?() A. The command is used to establish a static route.B. The default administrative distance is used.C. The command is used to configure the default route.D. The subnet mask for the source address is 255.255.255.0E. The command is used to establish a stub network
Which three are used in configuring Call Manager dial plans？ （）A、 route listB、 route groupC、 gateway listD、 route pattern
You have a router running BGP for the MPLS network and OSPF for the local LAN network at the sales office. A route is being learned from the MPLS network that also exists on the OSPF local network. It is important that the router chooses the local LAN route being learned from the downstream switch running OSPF rather than the upstream BGP neighbor. Also， if the local OSPF route goes away， the BGP route needs to be used. What should be configured to make sure that the router will choose the LAN network as the preferred path？（）A、static route needs to be addedB、floating static route needs to be addedC、bgp backdoor commandD、ospf backdoor command
Which of the following commands should be used to make permanent static route entries that will persist across reboots？（）A、chrootB、route staticC、route addD、smitty route
Which of the following commands will enable you to see the contents of the IP routing table andsend the output to a TFTP server at the same time？（）A、show ip route ∣ to tftp：//192.168.1.1/route.txtB、show ip route ∣ tee tftp：//192.168.1.1/route.txtC、show ip route ∣ include tftp：//192.168.1.1/route.txtD、show ip route ft include tJtp：//19Z168.1.1/route.txtE、show ip route ∣ redirect tftp：//192.168.1.1/route.txt
The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）A、The default administrative distance is used.B、The command is used to establish a static route.C、The command is used to configure the router interfaces.D、The command is used to establish a stub network.E、The subnet mask for the source address is 255.255.255.0
Which of the following should be flashed on a firewall to make sure it is the most current version available?（）A、FirmwareB、ACLsC、DefinitionsD、Route lists
Which of the following commands is used to determine the route that the IP packets take to a network host?（）A、 route B、 netstat C、 iptrace D、 traceroute
A customer who has a two node PowerHA cluster， with each node being at a different site and using cross siteLVM， plans to add a third heartbeat to further reduce the chance of data divergence or partitioned cluster. Theheartbeat will make use of spare adapters in the nodes. However， the heartbeats must go via an externalnetwork requiring static routes to be added for cluster functionality.How can this be achieved？（）A、Configure the static route in the /etc/rc.net fileB、Using application Start/Stop scripts to manage the static routeC、Configure Pre and Post event commands to manage the static routeD、Using smitty route command to create the static route and update the ODM
Which of the following commands should be used to display a system routing table?（）A、 route B、 netstat C、 iptrace D、 traceroute
What is the role of route preference?（）A、It is used to determine which route should become active.B、It is used to select which routing table to use for forwarding.C、It is used to determine what routes to accept into the routing table.D、It is used to select the best route between multiple equal cost paths.
单选题What is the role of route preference?（）AIt is used to determine which route should become active.BIt is used to select which routing table to use for forwarding.CIt is used to determine what routes to accept into the routing table.DIt is used to select the best route between multiple equal cost paths.
多选题The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?（）AThe command is used to establish a static route.BThe default administrative distance is used.CThe command is used to configure the default route.DThe subnet mask for the source address is 255.255.255.0EThe command is used to establish a stub network
单选题Which command will silently drop a matching packet?（）Aset routing-options static route 10.1.1.1/32 no-retainBset routing-options static route 10.1.1.1/32 discardCset routing-options static route 10.1.1.1/32 rejectDset routing-options static route 10.1.1.1/32 passive
单选题A customer who has a two node PowerHA cluster， with each node being at a different site and using cross siteLVM， plans to add a third heartbeat to further reduce the chance of data divergence or partitioned cluster. Theheartbeat will make use of spare adapters in the nodes. However， the heartbeats must go via an externalnetwork requiring static routes to be added for cluster functionality.How can this be achieved？（）AConfigure the static route in the /etc/rc.net fileBUsing application Start/Stop scripts to manage the static routeCConfigure Pre and Post event commands to manage the static routeDUsing smitty route command to create the static route and update the ODM
单选题You have just configured a static default route on router TK1. What is the purpose of a default route?（）AIt is a route to be used when the routing protocol fails.BIt is a route configured by an ISP that sends traffic into a corporate network.CIt is a route used when a packet is destined for a remote network that is not listed in the routing table.DIt is a route manually configured for a specific remote network for which a routing protocol is not configured.EIt is used to send traffic to a stub network.
单选题Given the following policy: Which action occurs when the static route 192.168.0.0/25 is evaluated by the policy main-policy?（）A The route is not advertised into BGP.A.The route is not advertised into BGP.B The route is advertised into BGP with metric 10.B.The route is advertised into BGP with metric 10.C The route is advertised into BGP with metric 20.C.The route is advertised into BGP with metric 20.D The route is advertised into BGP with default metric.D.The route is advertised into BGP with default metric.
单选题Which command is used to configure a default route?（）Aip route 172.16.1.0 255.255.255.0 0.0.0.0Bip route 172.16.1.0 255.255.255.0 172.16.2.1Cip route 0.0.0.0 255.255.255.0 172.16.2.1Dip route 0.0.0.0 0.0.0.0 172.16.2.1
单选题You have a router running BGP for the MPLS network and OSPF for the local LAN network at the sales office. A route is being learned from the MPLS network that also exists on the OSPF local network. It is important that the router chooses the local LAN route being learned from the downstream switch running OSPF rather than the upstream BGP neighbor. Also， if the local OSPF route goes away， the BGP route needs to be used. What should be configured to make sure that the router will choose the LAN network as the preferred path？（）Astatic route needs to be addedBfloating static route needs to be addedCbgp backdoor commandDospf backdoor command
单选题Which statement describes Reverse Route Injection （RRI）？（）AA static route that points towards the Cisco Easy VPN server is created on the remote client.BA static route is created on the Cisco Easy VPN server for the internal IP address of each VPN client.CA default route is injected into the route table of the remote client.DA default route is injected into the route table of the Cisco Easy VPN server.
单选题Which of the following commands should be used to display a system routing table?（）A route B netstat C iptrace D traceroute
单选题Which of the following commands is used to determine the route that the IP packets take to a network host?（）A route B netstat C iptrace D traceroute
单选题Which of the following commands will enable you to see the contents of the IP routing table andsend the output to a TFTP server at the same time？（）Ashow ip route ∣ to tftp：//192.168.1.1/route.txtBshow ip route ∣ tee tftp：//192.168.1.1/route.txtCshow ip route ∣ include tftp：//192.168.1.1/route.txtDshow ip route ft include tJtp：//19Z168.1.1/route.txtEshow ip route ∣ redirect tftp：//192.168.1.1/route.txt