Which encapsulation types are configurable on a Cisco switch for a trunk? (Select two answer choices)A. VTPB. ISLC. CDPD. 802.1QE. 802.1pF. LLCG. IETF
Which encapsulation types are configurable on a Cisco switch for a trunk? (Select two answer choices)
A. VTP
B. ISL
C. CDP
D. 802.1Q
E. 802.1p
F. LLC
G. IETF
相关考题：
如下图所示，3com和Cisco公司的交换机相互连接，在两台交换机之间需传输ULANID为1、10、20和30的4个VLAN信息，Catalyst 3548交换机VLAN Trunk的正确配置是A．Switch-3548 (config-if) #switchport trunk encapsulation dot 1 q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30B．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation isl Switch-3548 (config-if) #switchport trunk allowed vlan 1-30C．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation negotiate Switch-3548 (config-if) #switchport trunk allowed vlan 1-30D．Switch-3548 (config-if) #switchport mode trunk Switch-3548 (config-if) #switchport trunk encapsulation dot 1q Switch-3548 (config-if) #switchport trunk allowed vlan 1,10,20,30
What are two characteristics of "store and forward" switching? (Select two answer choices)A．Latency fluctuates regardless of frame. size.B．The switch receives the complete frame. before beginning to forward it.C．Latency through the switch varies with frame. length.D．The switch checks the destination address upon receipt of headers.
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)A. Switch(vlan) mode trunkB. Switch(config) switchport access mode trunkC. Switch(config-if) switchport mode trunkD. Switch(config-if) switchport trunk encapsulation dot1qE. Switch(config) switchport access mode 1F. Switch(vlan) trunk encapsulation dot1q
Which two of the addresses below are available for host addresses on the Ezonexam subnet 192.168.15.19/28? (Select two answer choices)A. 192.168.15.17B. 192.168.15.14C. 192.168.15.29D. 192.168.15.16E. 192.168.15.31F. None of the above
What must the Ezonexam network administrator do in order to successfully configure a VLAN trunk between two switches named VE1 and VE2? (Select two answer choices)A. Set each end of the trunk line to IEEE 802.1Q encapsulation.B. Set the same VTP management domain name on both switches.C. Set all ports on the two switched as access ports.D. Configure one of the two switches as a VTP server.E. Connect the two switches using a rollover cable.F. Use a router to forward VTP traffic between the VLANs.
Which of following VLAN frame. encapsulation types are configurable on a Cisco switch? (Select two answer choices.)A. VTPB. 802.1QC. LLCD. ISLE. CDPF. PAP
Which of the following are VLAN frame. encapsulation types that may be configured on a Catalyst switch? (Choose two.)A. VTPB. ISLC. CDPD. 802.1QE. 802.1pF. LLC
Which two of the following values does STP take into consideration when it elects the root bridge? (Select two answer choices)A. The BPDU version numberB. The access layer bridge settingC. The Bridge IDD. The spanning-tree update numberE. The bridge priorityF. The VLAN number
You are bringing up a new Ezonexam switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?A．Switch(config)# switchport trunk encapsulation islB．Switch(config)# switchport trunk encapsulation ietfC．Switch(config-if)# switchport trunk encapsulation islD．Switch(config-if)# switchport trunk encapsulation ietfE．Switch(config-if)# switchport trunk encapsulation dot1q
Which commands, when used together, would create an 802.1Q link?() A. Switch(vlan)# mode trunkB. Switch(config)# switchport access mode trunkC. Switch(config-if)# switchport mode trunkD. Switch(config-if)# switchport trunk encapsulation dot1qE. Switch(config)# switchport access mode 1F. Switch(vlan)# trunk encapsulation dot1q
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method.When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A. Switch(config)# switchport trunk encapsulation islB. Switch(config)# switchport trunk encapsulation ietfC. Switch(config-if)# switchport trunk encapsulation islD. Switch(config-if)# switchport trunk encapsulation ietfE. Switch(config-if)# switchport trunk encapsulation dot1q
Which commands, when used together, would create an 802.1Q link?（）A、Switch(vlan)# mode trunkB、Switch(config)# switchport access mode trunkC、Switch(config-if)# switchport mode trunkD、Switch(config-if)# switchport trunk encapsulation dot1qE、Switch(config)# switchport access mode 1F、Switch(vlan)# trunk encapsulation dot1q
能够在CiscoIOS软件中正确地将端口配置为ISL封装的命令是（）。A、Switch(config-if)#switchport mode trunk islB、Switch(config-if)#switchport mode encapsulation islC、Switch(config-if)#switchport trunk encapsulation islD、Switch(config-if)#switchport mode trunk encapsulation isl
Which of following VLAN frame encapsulation types are configurable on a Cisco switch?（）A、VTPB、802.1QC、LLCD、ISLE、CDPF、PAP
Which encapsulation types are configurable on a Cisco switch for a trunk?（）A、VTPB、ISLC、CDPD、802.1QE、802.1pF、LLCG、IETF
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A、Switch(config)# switchport trunk encapsulation islB、Switch(config)# switchport trunk encapsulation ietfC、Switch(config-if)# switchport trunk encapsulation islD、Switch(config-if)# switchport trunk encapsulation ietfE、Switch(config-if)# switchport trunk encapsulation dot1q
Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）A、 Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.B、 This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.C、 The router at RemoteB must be replaced by a Cisco router.D、 Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.E、 There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.
Which two commands can be used to verify a trunk link configuration status on a given cisco switch?（）A、show interfaces interfaceB、show interfaces trunkC、show interfaces switchportD、show ip interface briefE、show interfaces vlan
Which two commands can be used to verify a trunk link configurationt status on a given cisco switch?（）A、show interfaces interfaceB、show interfaces interface trunkC、show interfaces interface switchportD、show ip interface briefE、show interfaces vlan
You need to configure a new Company switch for trunking. Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）A、 CompanySwitch（config-if）#switchport trunk encapsulation dot1qB、 CompanySwitch（config-if）#switchport trunk encapsulation itefC、 CompanySwitch（config-if）#switchport trunk encapsulation fddiD、 CompanySwitch（config-if）#switchport trunk encapsulation islE、 None of the other alternatives apply
多选题Which two commands can be used to verify a trunk link configuration status on a given cisco switch?（）Ashow interfaces interfaceBshow interfaces trunkCshow interfaces switchportDshow ip interface briefEshow interfaces vlan
单选题You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）ASwitch(config)# switchport trunk encapsulation islBSwitch(config)# switchport trunk encapsulation ietfCSwitch(config-if)# switchport trunk encapsulation islDSwitch(config-if)# switchport trunk encapsulation ietfESwitch(config-if)# switchport trunk encapsulation dot1q
单选题You need to configure a new Company switch for trunking. Which switch command enables a trunking protocol that appends a four byte CRC to the packet？（）A CompanySwitch（config-if）#switchport trunk encapsulation dot1qB CompanySwitch（config-if）#switchport trunk encapsulation itefC CompanySwitch（config-if）#switchport trunk encapsulation fddiD CompanySwitch（config-if）#switchport trunk encapsulation islE None of the other alternatives apply
多选题Which of following VLAN frame encapsulation types are configurable on a Cisco switch?（）AVTPB802.1QCLLCDISLECDPFPAP
多选题Which encapsulation types are configurable on a Cisco switch for a trunk?（）AVTPBISLCCDPD802.1QE802.1pFLLCGIETF
多选题Which two commands can be used to verify a trunk link configurationt status on a given cisco switch？（）Ashow interfaces interfaceBshow interfaces interface trunkCshow interfaces interface switchportDshow ip interface briefEshow interfaces vlan
单选题Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）A Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.B This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.C The router at RemoteB must be replaced by a Cisco router.D Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.E There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.