Which of the following are VLAN frame. encapsulation types that may be configured on a Catalyst switch? (Choose two.)A. VTPB. ISLC. CDPD. 802.1QE. 802.1pF. LLC
Which of the following are VLAN frame. encapsulation types that may be configured on a Catalyst switch? (Choose two.)
A. VTP
B. ISL
C. CDP
D. 802.1Q
E. 802.1p
F. LLC
相关考题：
Which of following VLAN frame. encapsulation types are configurable on a Cisco switch? (Select two answer choices.)A. VTPB. 802.1QC. LLCD. ISLE. CDPF. PAP
Which encapsulation types are configurable on a Cisco switch for a trunk? (Select two answer choices)A. VTPB. ISLC. CDPD. 802.1QE. 802.1pF. LLCG. IETF
A new switch is installed in the Ezonexam network. This switch is to be configured so that VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur? (Choose all that apply).A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named EZONEXAM. Which of the following need to be completed for the creation of this new VLAN? (Select all that apply)A. The EZONEXAM VLAN must be created.B. The desired ports must be added to the new EZONEXAM VLAN.C. The EZONEXAM VLAN must be added to all of the domains.D. The EZONEXAM VLAN must be named.E. An IP address must be configured for the EZONEXAM VLAN.F. None of the above. VLAN creations are automatic.
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? (Choose two)A. The switch must be reachable through a port connected to its management VLAN.B. The switch console port must be connected to the Ethernet LAN.C. The switch must be fully configured as an SNMP agent.D. The switch must be configured with an IP address, subnet mask, and default gateway.E. The switch management VLAN must be created and have a membership of at least one switch port.F. The switch must be connected to a router over a VLAN trunk.
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A. The switch name must match the workgroup name of the local network.B. The switch must be configured with an IP address and default gateway.C. The remote workstations must have access to the management VLAN of the switch.D. CDP must be enabled on the switch so that it can be located by other devices on the network.
Catalyst switches utilize a special technology to identify and prevent topology loops and ensure that data flows properly through a single network path. What is the name of this technology?() A. VTPB. ISLC. 802.1QD. STPE. None of the above
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?() A. Switch(config-if)# vlan allB. Switch(config-if)# switchport trunk encapsulation dot1qC. Switch(config-if)# switchport access vlan allD. Switch(config-if)# switchport mode trunkE. Switch(config-if)# switchport access vlan 303
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.Which of the conditions below have to be met in order for this to occur?（）A. The switch that will share the VLAN information must be in the VTP Server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be configured to use the same VTP version.E. The switches must be configured to use the same STP version.F. The switches must be configured to use the same type of ID tagging.G. The switches must be connected over VLAN trunks.
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A. The switch that will share its VLAN configuration must be in VTP server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be connected over VLAN trunks.E. The switches must be configured to use the same STP version.F. The switches must have VTP pruning activated.
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named TESTKING. Which of the following need to be completed for the creation of this new VLAN?() A. The TESTKING VLAN must be created.B. The desired ports must be added to the new TESTKING VLAN.C. The TESTKING VLAN must be added to all of the domains.D. The TESTKING VLAN must be named.E. An IP address must be configured for the TESTKING VLAN.F. None of the above. VLAN creations are automatic.
Which of the following three port types are valid Spanning Tree port types？（Choose the best threeanswers.）（）A、Designated portB、Nonswitch portC、Switch portD、Nonroot portE、Nondesignated portF、Root port
Which of following VLAN frame encapsulation types are configurable on a Cisco switch?（）A、VTPB、802.1QC、LLCD、ISLE、CDPF、PAP
In a RSTP implementation, which of the following two link types are used? （）(Choose two.)A、SharedB、Point-to-PointC、DesignatedD、Multiaccess non-broadcast
Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）A、Switch(config-if)# vlan allB、Switch(config-if)# switchport trunk encapsulation dot1qC、Switch(config-if)# switchport access vlan allD、Switch(config-if)# switchport mode trunkE、Switch(config-if)# switchport access vlan 303
Which of the following are VLAN frame encapsulation types that may be configured on a Catalyst switch?（）A、VTPB、ISLC、CDPD、802.1QE、802.1pF、LLC
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A、The switch that will share its VLAN configuration must be in VTP server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be connected over VLAN trunks.E、The switches must be configured to use the same STP version.F、The switches must have VTP pruning activated.
Which two types of activities does the Lightweight Access Point Protocol （LWAPP） define？ （Choose two.）（）A、 access point certification and software controlB、 compression and Layer 3 address mappingC、 Layer 3 addressing and distributionD、 packet encapsulation， fragmentation， and formattingE、 SNMP monitoring services
Which of the following is not information provided from an IP phone to a Catalyst switch using CDP？（）A、 device PoE requirementsB、 device IP addressC、 device voice VLAN IDD、 device platform
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named TESTKING. Which of the following need to be completed for the creation of this new VLAN?（）A、The TESTKING VLAN must be created.B、The desired ports must be added to the new TESTKING VLAN.C、The TESTKING VLAN must be added to all of the domains.D、The TESTKING VLAN must be named.E、An IP address must be configured for the TESTKING VLAN.F、None of the above. VLAN creations are automatic.
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?（）A、The switch that will share the VLAN information must be in the VTP Server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be configured to use the same VTP version.E、The switches must be configured to use the same STP version.F、The switches must be configured to use the same type of ID tagging.G、The switches must be connected over VLAN trunks.
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
多选题Which of the following are VLAN frame encapsulation types that may be configured on a Catalyst switch?（）AVTPBISLCCDPD802.1QE802.1pFLLC
多选题Which two types of activities does the Lightweight Access Point Protocol （LWAPP） define？ （Choose two.）（）Aaccess point certification and software controlBcompression and Layer 3 address mappingCLayer 3 addressing and distributionDpacket encapsulation， fragmentation， and formattingESNMP monitoring services
多选题Which of following VLAN frame encapsulation types are configurable on a Cisco switch?（）AVTPB802.1QCLLCDISLECDPFPAP
多选题Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）ASwitch(config-if)# vlan allBSwitch(config-if)# switchport trunk encapsulation dot1qCSwitch(config-if)# switchport access vlan allDSwitch(config-if)# switchport mode trunkESwitch(config-if)# switchport access vlan 303
多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.