In BGP graceful restart, how does a peer router indicate the end of a route exchange?() A. an open message with the E bit setB. an update message with the E bit setC. an open message with an end-of-RIB markerD. an update message with an end-of-RIB marker
In BGP graceful restart, how does a peer router indicate the end of a route exchange?()
A. an open message with the E bit set
B. an update message with the E bit set
C. an open message with an end-of-RIB marker
D. an update message with an end-of-RIB marker
相关考题:
You are troubleshooting a routing issue and need to check the hop-by-hop path to the 10.10.10.10 destination. Which three commands would display the path?() A. user@router# traceroute 10.10.10.10B. user@router ping record-route 10.10.10.10C. user@routertraceroute 10.10.10.10D. user@router# run traceroute 10.10.10.10E. user@router# ping record-route 10.10.10.10
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?() A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0E. Router(config)# ip route any any e0
定义route-policytest如下:下列描述错误的是() A.只有包含community100:1或者as-path为100的BGP路由才会通过route-policy test,并将AS-PATH改为200B.只有包含community100:1并且as-path为100的BGP路由才会通过route-policy test,并将AS-path改为200C.只有community为100:1并且AS-PATH为100的BGP路由才会通过route-policy test,并将AS-PATH改为200D.Community为100:1并且AS-PATH为100的BGP路由会通过route-policy test,并将AS-PATH改为200
当对一个BGP邻居配置了多个路由选择工具进行路由过滤时,下列描述错误的是() A.对于peer接收路由,IP-Prefix先与route-policy被处理B.对于peer接收路由,route-policy先与IP-Prefix被处理C.对于peer发送路由,IP-prefix先与route-policy被处理D.对于peer发送路由,route-policy先与IP-Prefix被处理
仅用于BGP协议,匹配BGP路由信息的AS-PATH的路由选择工具是() A.route-policyB.ip-prefixC.as-path-filterD.community-filter
哪条 IPv6 静态路由将作为通过 OSPF 学习的动态路由的备份路由?A.Router1(config)# ipv6 route 2001:db8:acad:1::/32 2001:db8:acad:6::2 100B.Router1(config)# ipv6 route 2001:db8:acad:1::/32 2001:db8:acad:6::100C.Router1(config)# ipv6 route 2001:db8:acad:1::/32 2001:db8:acad:6::2 200D.Router1(config)# ipv6 route 2001:db8:acad:1::/32 gigabitethernet0/0 2001:db8:acad:6::100 100
查看路由表的信息的命令是()。A.Router#show ip routingB.Router#show ip routerC.Router#show ip routeD.Router#show ip-route