0， 1， 32，81， 64， （ ）A．32B．49C．25D．36
0， 1， 32，81， 64， （ ）
A．32
B．49
C．25
D．36
相关考题：
Which simplified IPv6 address is the same as the IP address 2001:0000:1000:0000:0000:cbff:0020:0001／64?() A. 2001::1::cbff:2:0001/64B. 2001::1000::cbff:20:1/64C. 2001:0:1000::cbff:20:1/64D. 2001:0:1:0:0:cbff:2:1/64
Router R1 has been conf igured with an ipv6 route 2000::／64 S0／0／0 64 command.Which of the following does the 64 at the end of the command represent?() A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receiveA. Route 2000::/64 will be redistributed.B. Route 2 000:0:0:1::/64 will be redistributed.C. Route 2000:1:213:19FF:FE7B:5004/128 will be redistributed.D. No routes will be redistributed because of the omission of the subnets parameter of the redistribute command.
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0A. OSPF works on F0/0 and S0/0/0 without further configurationB. OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modEC. OSPF works with the addition of one command: an router - id command in OSPF router configuration modED. OSPFv3 needs at least two more configuration commands before it works on R1
2、假设一台计算机的字长为32位，内存容量为64MB。 如果内存是按字寻址的，那么它的寻址范围是[x] ~ [y]A．0 ~ 16MB．0 ~ 16M-1C．0 ~ 16MB-1D．0 ~ 64ME．0 ~ 64M-1F．0 ~64MB-1G．16MH．16MBI．64MJ．64MB
某计算机的字长为16位，它的存储容量为64KB，若按字寻址，其寻址范围是（)。A．0～32KB．0～64KC．0～64K-1D．0～32K-1