You are the network administrator for Ezonexam. You are installing Windows 2000 Server on a new computer by using the Windows 2000 Server compact disk. The computer has five 18-GB hard disks Dick0, Disk1, Disk2, Disk3, and Disk4. The disks do not have any partitions defined.You want to use as much space on Disk0 as possible for the partition on which Windows 2000 Server is installed. You want the disk on which you install Windows 2000 Server to be fault tolerant. You also want as much disk space as possible across the other disks to be available for data storage and to be fault tolerant.What should you do? (Each correct answer presents part of the solution. Choose three)A. Install Windows 2000 Server on a 4-GB NTFS partition on Disk 0. Configure the five disks as dynamic disks.B. Install Windows 2000 Server on a 18-GB NTFS partition on Disk 0. Configure the five disks as dynamic disks.C. Create a RAID-5 volume using Disk2, Disk3, and Disk4.D. Create a stripped volume using Disk2, Disk3, and Disk4.E. Create a RAID-5 volume using all disks.F. Create a stripped volume using all disks.G. Select the volume on Disk0 and add a mirror using Disk1.
You are the network administrator for Ezonexam. You are installing Windows 2000 Server on a new computer by using the Windows 2000 Server compact disk. The computer has five 18-GB hard disks Dick0, Disk1, Disk2, Disk3, and Disk4. The disks do not have any partitions defined.
You want to use as much space on Disk0 as possible for the partition on which Windows 2000 Server is installed. You want the disk on which you install Windows 2000 Server to be fault tolerant. You also want as much disk space as possible across the other disks to be available for data storage and to be fault tolerant.
What should you do? (Each correct answer presents part of the solution. Choose three)
A. Install Windows 2000 Server on a 4-GB NTFS partition on Disk 0. Configure the five disks as dynamic disks.
B. Install Windows 2000 Server on a 18-GB NTFS partition on Disk 0. Configure the five disks as dynamic disks.
C. Create a RAID-5 volume using Disk2, Disk3, and Disk4.
D. Create a stripped volume using Disk2, Disk3, and Disk4.
E. Create a RAID-5 volume using all disks.
F. Create a stripped volume using all disks.
G. Select the volume on Disk0 and add a mirror using Disk1.
相关考题：
You need to install Windows 2000 Server on one of your older Windows NT Server 4.0 computers. The server has dual processors, 2 GB of RAM, a RAID controller with five SCSI hard disks in an array, and a generic 10/100-MB network adapter. You begin the server installation by updating the SCSI firmware.You then start the installation of the Windows 2000 Server operating system. During the next portion of the installation, you receive an error message indicating that no hard disks can be found.You want to successfully install Windows 2000 Server on the computer.What should you do? (Each correct answer presents part of the solution. Choose two)A．Restart the installation by using the Windows 2000 Installation CD-ROM. Press F3 during the text-mode setup.B．Restart the installation by using the Windows 2000 Installation CD-ROM. Press F6 during the text-mode setup.C．Restart the installation by using a MS-DOS boot disk with a CD-ROM driver.D．Insert a disk with the original SCSI firmware.E．Insert a disk with the OEM SCSI driver.
You are the network administrator for Ezonexam. The network includes a Microsoft Windows NT Server 4.0 member server computer that has a non-Plug and Play ISA network adapter.You want to upgrade this computer to Microsoft Windows 2000 Server. You also want to ensure that you maintain the current device configuration during the upgrade.What should you do? (Each correct answer presents part of the solution. Choose two)A. Install the latest driver for the network adapter.B. Disable the network adapter.C. Start the upgrade process by using Winnt32.exeD. Start the upgrade process by booting from the Windows 2000 Server compact disc.E. Configure BIOS to reserve the IRQ currently in use by the network adapter.F. Press F6 at the beginning of the text mode setup to specify an additional driver.
You are the desktop administrator for Ezonexam.com'ssalesdepartment. Ezonexam.com's network contains a RIS server.You need to install Windows 2000 Professional on a computer that has a SCSI disk subsystem. You start the computer by using the Windows 2000 Professional CD-ROM, and you begin the installation.However, Setup reports that it cannot find any disk on which to install Windows 2000 Professional.You start the computer by using a RIS bootable floppy disk, and you receive the same result.What should you do?A．Add an answer file to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS.B．Add the SCSI-controller driver to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS.C．Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide an answer file on a floppy disk.D．Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide a SCSI-controller driver on a floppy disk.E．Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide the appropriate HAL on a floppy disk.
You are the administrator of your company's network. The network is configured as shown in the exhibit.You want to install Windows 2000 Professional on 10 non-PXE-compliant computers that are on the marketing segment of your network. You start one of the computers by using a RIS boot disk. However, you cannot connect to the RIS server.You verify that the existing client computers on the network can connect to network servers, including the RIS server. The network router does not support BOOTP, so existing client computers use manually configured TCP/IP addresses. You want to enable the computers to connect to the RIS server.What should you do?A．Add a computer running DHCP Relay Agent to the marketing segment.B．Add a computer running the network monitor driver to the marketing segment.C．Move the Windows 2000 Server computer running WINS to the marketing segment.D．Move the Windows 2000 Server computer running Active Directory to the marketing segment.
You are the network administrator for Ezonexam. You are preparing to install Windows 2000 Server on a new computer. The computer is connected to a network that includes Windows 98 computers and Windows 2000 Server computers.You want to install Windows 2000 Server from source files that are located on a shared folder called I386 on a Windows 2000 Server computer named Ezonexam1.What should you do? (Each correct answer presents part of the solution. Choose two)A．On a Windows 2000 computer, use Makebt32.exe to create installation startup disks. Start the new computer by using the first disk.B．On a Windows 2000 computer, format a floppy disk. Copy NTLDR, Boot.ini, Ntdetect.com, and Ntbootdd.sys to this disk. Start the new computer by using the disk.C．Start the new computer by using a Windows 98 network boot disk.D．Connect to \\Ezonexam1\I386 and run Winnt32.exe.E．Connect to \\Ezonexam1\I386 and run Winnt.exe.
You are the administrator of a network that consists of a single Windows NT 4.0 domain. The network contains five Windows NT Server domain controllers and 1,000 Windows NT Workstation client computers.You want to install Windows 2000 Server on a new computer. You want the new computer to act as domain controller in the existing domain.What should you do?A．On the new computer, install Windows NT Server 4.0 and designate the computer as a BDC in the existing domain. Promote the computer to the PDC of the domain. Upgrade the computer to Windows 2000 Server.B．On the new computer, install Windows NT Server 4.0 and designate the computer as a PDC in a new domain that has the same NetBIOS name as the existing Windows NT domain. Upgrade the computer to Windows 2000 Server. Use the Active Directory sites and services to force synchronization of the domain controllers.C．Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory installation wizard to install Active Directory, specifying the same NetBIOS name for the Windows 2000 domain as the existing Windows NT domain. Restart the Windows NT PDC on the network and demote it to a BDC.D．Shut down the PDC of the existing Windows NT domain from the network. On the new computer, install Windows 2000 Server, and then run the Active Directory installation wizard to install Active Directory as a replica in the existing Windows NT domain. Promote the new computer to the PDC of the domain. Restart Windows NT PDC on the network and demote it to a BDC.
You are the administrator for your company's network. The network is configured as shown in the exhibit.You want to install Windows 2000 Professional on 20 new PXE-compliant computers on the marketing segment of your network. The new computers do not have operating systems installed.You create a RIS image. You load the image onto the RIS server. You then start the new computers.You find that the new computers cannot connect to the RIS server. You verify that the new computers cannot connect to the RIS server. You verify that the existing client computers in the network can connect to the network servers, including the RIS server. You want to enable the new computers to connect to the RIS server.What should you do?A．Add a Windows 2000 Server computer running WINS to the network.B．Add a Windows 2000 Server computer running DHCP to the network.C．Add the domain Everyone group to the RIS OS image security settings.D．Place the new computers on the same segment as the RIS server.
Your Windows 2000 Server computer named EzonexamSrv contains a single 18-GB hard disk. The drive is configured as a basic disk and has two partitions. Partition C is 2 GB in size and contains the operating system files. Partition D is 16 GB in size and contains user data that is updated frequently.Both partitions are formatted as NTFS. Both partitions are backed up to a tape every evening at 10:00 P.M.You have a current Emergency Repair Disk (ERD) for EzonexamSrv, and the Recovery Console is installed on the computer.One day at4:00 P.M., the server fails. You attempt to restart EzonexamSrv, but you receive the following error message:"Boot disk or operating system not found".You use Recovery Console to discover that the files on partition C are corrupted.You need to recover EzonexamSrv from the failure as quickly as possible. You also must recover as much user data as possible.What should you do?A．Use the ERD to start the computer. Replace the corrupted files on partition C by copying them from a Windows 2000 Server CD-ROM.B．Boot the Recovery Console. Copy any files that have changed since 10:00 P.M. the previous evening to a second server. Use the most recent tape backup to restore the remaining user data to the second server.C．Start the computer by using a Windows 2000 Server CD-ROM. Select the Repair option in Setup.D．Install a second hard disk in the computer. Install Windows 2000 Server on the new hard disk. Re-create the shared folders on the first hard disk.
You are the administrator of a Windows 2000 Server network. On each server, you format a separate system partition and a separate boot partition as NTFS.Several months later, you shut down one of the servers for the maintenance. When you try to restart the server, you receive the following error message "NTLDR is missing. Press any key to restart".You want to install a new NTLDR file on the server, but you do not want to lose any settings you made since the original installation. What should you do?A．Start the computer by using the Windows 2000 Server CD-ROM and choose to repair the installation. Select the Recovery Console and copy the NTLDR file on the CD-ROM to the root of the system volume.B．Start the computer by using the Windows 2000 Server CD-ROM and choose to reinstall. When installation is complete, copy the NTLDR file to the root of the boot volume.C．Start the computer by using a Windows 2000 bootable floppy disk. From the command prompt, run the sfc/scanboot command.D．Start the computer by using a Windows 2000 bootable floppy disk. Run the File Signature Verification utility.
Ezonexam has 50 offices. The employees in these offices have limited knowledge of Windows 2000. Each office has a network of between five and 20 client computers. The office networks are connected to each other. The company is buying 50 identical computers to run Windows 2000 Server in these offices. The server must be installed to the company's standard configuration. You use Setup Manager to create a network shared distribution folder and a Unattend.txt file that specifies the company's standard configuration.You want to automate the installation process as much as possible, in the least possible amount of time.What should you do?A．Run Makebt32.exe to create four installation startup disks and add the Unattend.txt file to the first disk. Instruct an employee at each office to start the installation by using these disks.B．Create a Microsoft MS-DOS network boot disk that makes a connection to the network shared distribution folder and runs the winnt command with the /s and /u switches. Instruct an employee at each office to start the installation by using this disk.C．Create a floppy disk that contains only the Unattend.txt file. Instruct an employee at each office to start the installation by using the Windows 2000 Server compact disc, with the floppy disk inserted.D．Create a Windows 2000 folder on a hard disk. Copy the Windows 2000 Server compact disc to the folder. Add the Unattend.txt file to the folder. Copy the folder to a writeable CD. Instruct an employee at each office to start the installation by suing this CD.
Your network includes Windows 98 computers and Windows 2000 Server computers. You are adding a new computer to the network, and you plan to install Windows 2000 Server on the new computer. The computer has one 20-GB hard disk with no partitions defined.The Windows 2000 Server CD-ROM is unavailable. You want install Windows 2000 Server from source files that are located on a server on the network. You also want the entire hard disk of the new computer to be used for the system partition.What should you do?A．On another Windows 2000 computer, use Makebt32.exe to create installation startup disks. Start the new computer by using the first disk.B．On another Windows 2000 computer, format a floppy disk. Copy NTLDR, Boot.ini, Ntdetect.com, Ntbootdd.sys to this disk. Start the new computer by using the disk.C．Start the new computer by using a Windows 98 network boot disk. Connect to the network server. Run Dsclient.exe. Create and format a 20-GB FAT32 partition.D．Start the new computer by using a Windows 98 network boot disk. Create and format a single FAT32 partition. Connect to the network server. Run Winnt.exe.E．Start the computer by using a Windows 98 network boot disk. Create and format a single FAT32 partition. Start the new computer by using a Windows 2000 Emergency Repair Disk.
Your Windows 2000 Server computer has a 10-GB hard disk with two partitions: Drive C and drive D. Windows 2000 Server is installed on Drive D. Both partitions are formatted as NTFS. Your office experiences a power failure that causes your Windows 2000 Server computer to restart.When the computer is restarting, you receive the following error message "NTLDR is missing. Press any key to restart".What should you do?A．Start the computer by using Windows 2000 Server computer CD-ROM and choose to repair the installation. Select the Recovery Console and copy the NTLDR file on the CD-ROM to the root of the system partition.B．Start the computer in debugging mode. Copy the NTLDR file on the CD-ROM to the root of the system partition.C．Start the computer by using the Windows 2000 bootable floppy disk. From a command prompt, run the sfc/scanboot command.D．Start the computer by using a Windows 2000 bootable floppy disk. Run the File Signature Verification utility.
You are preparing to install Windows 2000 Server on a new computer. The computer is connected to a network that includes Windows 98 computers and Windows 2000 Server computers.You want to install Windows 2000 Server from source files that are located on a server on the network.What should you do?A．Start the new computer by using a Windows 98 network boot disk. Connect to the network server. Run Winnt32.exe.B．Start the new computer by using Windows 98 network boot disk. Connect to the network server. Run Winnt.exe.C．On a Windows 2000 Server computer, use Makebt32.exe to create installation startup disk. Start the new computer by using the first disk.D．On a Windows 2000 computer, format a floppy disk. Copy NTLDR, boot.ini, Ntdetect.com, Ntbootdd.sys to this disk. Start the new computer by using the disk.
You are the network administrator for Ezonexam.com.You are planning to install 10 new Windows 2000 Server computers. Ezonexam has a tight production schedule that requires no changes be made to the Active Directory except during scheduled outages. You schedule the installations during an upcoming network outage which will occur betweenmidnight and 8:00 A.M.You want to complete the installations before production begins in the morning.What should you do?A．Perform. the installations by using four floppy disks create with the Makebt32.exe utility.B．Perform. the installations by using four floppy disks create with the Makeboot.exe utility.C．Perform. the installations by using the Windows 2000 Installation compact disc.D．Perform. the installations by using the Windows 2000 Installation compact disc and a floppy disk containing a Winnt.sif file.
You are installing Windows 2000 Server on a new computer that has a single 10-GB SCSI disk. The disk controller is not included on the current Hardware Compatibility List (HCL). You start the computer by using the Windows 2000 Server CD-ROM.When the computer restarts at the end of the text mode portion of Windows 2000 setup, you receive the following STOP error: "INACCESSIBLE_BOOT_DEVICE."Which two actions should you take to eliminate the STOP error? (Choose Two)A．Restart the Windows 2000 Setup by using the Windows 2000 Server CD-ROM.B．Select Safe Mode from the Windows 2000 boot menu.C．Remove the Windows 2000 Server CD-ROM from the CD-ROM drive.D．Install a driver for the SCSI controller from a floppy disk.E．Use Device Manager to update the driver for the SCSI controller.
You are the network administrator for Ezonexam.The network includes a Windows 2000 Server computer that contains a single 36-GB hard disk. The drive is configured as a basic disk and has two partitions. Partition C is 4 GB in size and contains the operating system files. Partition D is 32 GB in size and contains user data that is updated frequently.Both partitions are formatted as NTFS. Both partitions are backed up to a tape every evening at 11:00 P.M.You have a current Emergency Repair Disk (ERD) for the computer, and Recovery Console is installed on the computer.One day at2:00 P.M., the server fails. You attempt to restart the computer, but you receive the following error message: "Boot disk or operating system not found." You use Recovery Console to discover that the files on partition C are corrupted.You want to recover the server from the failure as quickly as possible. You also want to recover as much user data as possible.What should you do?A．Start the computer by using a Windows 2000 Server compact disc. Select the Repair option in Setup.B．Install a second hard disk in the computer. Install Windows 2000 Server on the new hard disk. Re-create the shared folders on the first hard disk.C．Use a Windows 2000 Server boot floppy disk to start the computer. Replace the corrupted files on partition C by copying them from the Emergency Repair Disk.D．Boot to the Recovery Console. Copy any files that have changed since 11:00 P.M. the previous evening to a second server. Use the most recent tape backup to restore the remaining user data to the second server.
You want to upgrade a Windows NT Server 4.0 computer to Windows 2000 Server. The system partition uses the FAT file system.You start the Setup program by starting the computer from the Windows 2000 Server CD-ROM.However, you receive the following error message, "You chose to install Windows 2000 on a partition that contains another operating system. Installing Windows 2000 on this partition might cause the operating system to function improperly".You are unable to perform. the upgrade. What should you do to resolve the problem?A．Convert the system partition to NTFS.B．Disable Advanced Configuration and Power Interface (ACPI) support for the computer.C．Restart the computer, and then run Winnt32.exe from the Windows NT Server 4.0 environment.D．Remove the Windows 2000 Server CD-ROM and restart the computer by using the setup floppy disks.
You are the network administrator for Ezonexam.com.You need to upgrade a computer from Windows NT Server 4.0 to Windows 2000 server. The server has dual processors, 2 GB of RAM, a RAID controller with five SCSI hard disks in an array, and a generic 10/100-MB network adapter. You begin the installation of the Windows 2000 Server operating system.During the text portion of the installation, you receive the following error message:"Stop 0x00000078 Inaccessible_boot_device."You want to successfully upgrade the computer.What should you do? (Each answer presents part of the solution. Choose two)A．Start the computer by using a DOS disk and run FDISK.B．Update the firmware on the RAID controller.C．Restart the installation. During the text-mode setup-mode setup, press F6.D．Restart the installation. During the text-mode setup, create a new partition.E．Insert a floppy disk containing the OEM SCSI driver and specify the additional driver.
You are the administrator of a Windows 2000 network. You install Windows 2000 Professional on a new computer and configure the TCP/IP settings to have a static IP address. While testing network connectivity from the new computer, you discover an error in the DNS server address that is configured in the TCP/IP settings. You configure the correct DNS server address, which is 10.1.1.5. However, you are still unable to successfully connect to network resources by name. You run the IPconfig/all command. The results indicate that the DNS server address is now configured as 0.0.0.0 You need to ensure that the computer can connect to network resources by name. What should you do?（）A、Stop and restart the DNS Client service.B、Add 10.1.1.5 to the DNS server list on the TCP/IP Advanced Properties tab.C、Add an A （host） record for the computer to the DNS server’s zone file.D、Configure your DHCP server to have a DNS server address of 10.1.1.5.
You are the desktop administrator for Company.com’s sales department. Company.com’s network contains a RIS server. You need to install Windows 2000 Professional on a computer that has a SCSI disk subsystem. You start the computer by using the Windows 2000 Professional CD-ROM, and you begin the installation. However, Setup reports that it cannot find any disk on which to install Windows 2000 Professional. You start the computer by using a RIS bootable floppy disk, and you receive the same result. What should you do?（）A、 Add an answer file to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS. B、 Add the SCSI-controller driver to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS. C、 Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide an answer file on a floppy disk. D、 Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide a SCSI-controller driver on a floppy disk. E、 Start the computer by using the Windows 2000 Professional CD-ROM, and run Setup. After Setup starts, provide the appropriate HAL on a floppy disk.
You are the administrator of your company’s network. You network has five Windows 2000 server computers and 75 Windows 2000 Professional computers. The Windows 2000 Professional computers were installed by using a RIS image on one of the Windows 2000 Server computers. You need to upgrade several applications on the Windows 2000 Professional computers. The applications do not have built-in support for scripted installations. You want to accomplish the following goals: An unattended installation of the upgraded applications will be performed on the Windows 20000 Professional computers. Existing user environments will be maintained on the Windows 2000 Professional computers. The network name of each Windows 2000 Professional computer will be changed to match its asset tag. The RIS image and the upgraded applications will be enabled as they are added to the network. You take the following actions: Install the RIS image on a Windows 20000 Professional computer named Computer1. Install the upgraded applications on Computers1. Change the network name of Computer1 to %DMI-SERIAL_NUM%. Run RIPrep.exe on Computer1 to load the RIS image on to the RIS server. Start all of the Windows 2000 Professional computers, and then load the RIS image from the RIS server. Which result or results do these actions produce?（ ）A、An unattended installation of the upgraded applications will be performed on the Windows 2000 Professional computers.B、Existing user environments will be maintained on the Windows 2000 Professional computers.C、The network name of each Windows 2000 Professional computer will be changed to matchIts asset tag.D、The RIS image and the upgraded applications will be enabled as they are added to the N.etwork.
You are the desktop administrator for one of your company's branch offices. The network in the branch office consists of a single network segment, which contains a domain controller, a DHCP server, 10 Windows 2000 Server computers, and 50 Windows 2000 Professional computers. All servers and client computers are members of the company's Active Directory domain. You purchase 50 new client computers for the branch office. Each new client computer contains a built-in PXE-compliant network adapter. You install and configure RIS on one of the Windows 2000 Server computers that is on the network in the branch office. You create a Windows XP Professional RIS image on the Windows 2000 Server computer. You connect the new client computers to the network in the office, and you turn on each computer. Each computer displays a message stating that it cannot contact a PXE boot server. You verify that the RIS server is connected to the network. You need to ensure that the new client computers can connect to the RIS server and can begin installing Windows XP Professional. What should you do?（）A、Ask a domain administrator to authorize the RIS server. B、Grant the Everyone group Allow - Read NTFS permission on the RIS image.C、Install RIS on the domain controller. Copy the RIS image to the domain controller.D、Add a reservation for the RIS server to the DHCP server.
You are the desktop administrator for your company's sales department. The company's network contains a RIS server. You need to install Windows XP Professional on a computer that has a SCSI disk subsystem. You start the computer by using the Windows XP Professional CD-ROM, and you begin the installation. However, Setup reports that it cannot find any disks on which to install Windows XP Professional. You start the computer by using a RIS bootable floppy disk, and you receive the same result. What should you do?（）A、Add an answer file to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS. B、Add the SCSI-controller driver to the root directory of the RIS bootable floppy disk. Start the computer by using the RIS bootable floppy disk, and run Setup by using RIS. C、Start the computer by using the Windows XP Professional CD-ROM, and run Setup. After Setup starts, provide an answer file on a floppy disk. D、Start the computer by using the Windows XP Professional CD-ROM, and run Setup. After Setup starts, provide a SCSI-controller driver on a floppy disk. E、Start the computer by using the Windows XP Professional CD-ROM, and run Setup. After Setup starts, provide the appropriate HAL on a floppy disk.
ou need additional storage space on your Windows 2000 Professional computer. You install a second SCSI controller and a second hard disk. During the installation of the SCSI driver, you receive a warning that the driver is unsigned. You complete the installation of the driver and restart Windows 2000 Professional. During startup, you receive a Stop error. You need to correct the error and start Windows 2000 as quickly as possible. What should you do?（）A、Start the computer in Recovery Console. Delete the SCSI controller driver.B、Start the computer by using the last known good configuration.C、Start the computer by using the Windows 2000 startup floppy disks， and repair the system files.D、Start the computer by using the Windows 2000 startup floppy disks， and repair the registry.
You are the administrator of Company.com’s Windows 2000 network. Your computer is configured to use both Windows 2000 Professional and Windows NT Workstation 4.0 Service Pack 3. Your computer has three hard disks: Disk 0, Disk1, and Disk2. Windows NT Workstation 4.0 is installed on Disk 0. Windows 2000 Professional is installed on Disk1. You want to store your project files on Disk2. You configure Disk2 as a basic volume and format the volume as NTFS in Windows 2000 Professional. You then start Windows NT Workstation 4.0. You find that you cannot access your project files. You want to be able to access your project files when using either operating systems. What should you do?（）A、Upgrade Windows NT Workstation 4.0 to Service Pack 4 or later.B、Configure Disk 2 as a dynamic volume then format as an NTFS partition.C、Configure Disk 2 to use Encrypting File System （EFS）.D、Configure Disk 2 as a basic volume and forma the volume as FAT32.
You have updated the modem driver on your Windows 2000 Professional computer. You restart your computer. Immediately after you log on, you receive a stop error. You need to start Windows 2000. What must you do? （）A、Restart the computer in Safe Mode. Uninstall the modem driver.B、Restart the computer by using the last known good configuration.C、Restart the computer in Recovery Console. Replace the new Modem.inf file with the old modem.inf file.D、Start the computer from the Windows 2000 startup floppy disks. Repair the registry.E、Start the computer from the Windows 2000 startup floppy disks. Repair the system files.
单选题You have a computer that runs Windows XP Professional. The computer is a member of an Active Directory domain. A server administrator installs and shares a new printer on a server that runs Windows Server 2003. You need to configure the computer to print to the new printer. What should you do?（）AFrom the computer, install a local printer.BFrom the computer, install a network printer. CFrom the Active Directory domain, add the computer account for the Windows XP Professional computer to the Print Operators group. DFrom the Windows Server 2003 server, add the computer account for the Windows XP Professional computer to the Print Operators group.