XYZ公司深圳分公司的路由器的Serial0/0和Serial0/1接口通过两条广域网线路分别连接两个不同的ISP，通过这两个ISP都可以访问北京总公司的网站202.102.100.2。在深圳分公司的路由器上配置了如下的静态路由：iproute-static202.102.100.224Serial0/0iproute-static202.102.100.224Serial0/1那么关于这两条路由的描述哪些是正确的？（）。A、去往北京的流量通过这两条路由可以实现负载分担B、去往北京的这两条路由可以互为备份C、在该路由器的路由表中只会写入第二条路由D、在该路由器的路由表中只会写入第一条路由
XYZ公司深圳分公司的路由器的Serial0/0和Serial0/1接口通过两条广域网线路分别连接两个不同的ISP，通过这两个ISP都可以访问北京总公司的网站202.102.100.2。在深圳分公司的路由器上配置了如下的静态路由：iproute-static202.102.100.224Serial0/0iproute-static202.102.100.224Serial0/1那么关于这两条路由的描述哪些是正确的？（）。
- A、去往北京的流量通过这两条路由可以实现负载分担
- B、去往北京的这两条路由可以互为备份
- C、在该路由器的路由表中只会写入第二条路由
- D、在该路由器的路由表中只会写入第一条路由
相关考题：
在某路由器上已经配置了一个访问控制列表2，而且使用了防火墙功能。现在对所有通过Serial0接口的数据包使用规则1进行过滤。下面可以实现的是( )。A)在Serial0的接口模式下配置：ip access-group 2 0utB)在全局模式下配置：access-group 2 seria10 outC)在Serial0的接口模式下配置：access-group 2 inD)在Serial0的接口模式下配置：ip access-group 2 in
以下是使用E1线路实现多个64Kbit/s专线连接。当链路为T1时，channel-group编号为0～23，Timeslot范围为1～24；当链路为E1时， channel-group编号为0～30，Timeslot范围为1～31。路由器具体设置如下：Current configuration:version 11.2no service udp-small-serversno service tcp-small-servers!hostname router1!enable secret 5 $ 1 $ XN08 $ Ttr8nfLoP9.2RgZhcBzkk/enable password cisco!!ip subnet-zerocontroller E1 0framing NO-CRC4channel-group 0 timeslots 1channel-group 1 timeslots 2channel-group 2 timeslots 3!interface Ethernet0ip address 133.118.40.1 255.255.0.0media-type 10BaseTinterface Ethernet1no ip addressshutdowninterface Serial0:0ip address 202.119.96.1 255.255.255.252encapsulation hdlcno ip mroute-Cacheinterface Serial0:1ip address 202.119.96.5 255.255.255.252encapsulation hdlcno ip mroute-Cache!interface Serial0:2ip address 202.119.96.9 255.255.255.252encapsulation hdlcno ip mroute-Cacheno ip classlessip route 133.210.40.0 255.255.255.0 Serial0:0ip route 133.210.41.0 255.255.255.0 Serial0:1ip route 133.210.42.0 255.255.255.0 Serial0:2line con 0line aux 0line vty 0 4password cicsoIogin!endE1和CE1的主要区别是什么?
The output of s how ip eigrp topology on Router R1 shows the following output, which is all the output related to subnet 10.11.1.0/24. How many feasible successor routes does R1 have for 10.11.1.0/24?（）P 10.11.1.0/24, 2 successors, FD is 2172419via 10.1.1.2 (2172423/2 8167), Serial0/0/0.1via 10.1.1.6 (2172423/28167), Serial0/0/0.2A.0B.1C.2D.3
Which line from the output of the show ip interface command indicates a layer 1 problem?() A. Serial0/1 is up, line protocol is downB. Serial0/1 is down, line protocol is downC. Serial0/1 is up, line protocol is upD. Serial0/1 is administratively down, line protocol is down
Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）A.The Manchester serial address is 10.1.1.1B.The Manchester serial address is 10.1.1.2C.这个Manchester路由器串口地址为：10.1.12D.The London router is a Cisco 2610.E.The Manchester router is a Cisco 2610.F.The CDP information was received on port Serial0/0 of the Manchester router.G.The CDP information was sent by port Serial0/0 of the London Router.
什么是词dynamic的含义显示在显示帧中继map命令的输出显示?() A.该的Serial0/0接口被传输流量B.该DLCI100是动态路由器分配C.该的Serial0/0接口从DHCP服务器获取的172.16.3.1的IP地址D.的DLCI100将被动态地改变，以适应变化的帧中继云所需E.DLCI100和终端站IP地址172.16.3.1的映射是通过反向ARP学到
Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.() A.Router John uses alink-state routing protocol.B.Router John will receive routing updates on the Serial0/0 interface.C.Router John will receive routing updates on the Serial0/1 interface.D.Router John will send routing updates out the Serial0/0 interface.E.Router John will send routing updates out the FastEthernet0/0 interface.F.Router John will send routing updates out the Serial0/1 interface.
Refertotheexhibit.TheLaksideCompanyhastheinternetworkintheexhibit.TheadministratorwouldliketoreducethesizeofroutingtableontheCentralrouter.WhichpartialroutingtableentryintheCentralrouterepresentsaroutesummarythatrepresentsthevlansinPhoenixbutnoadditionalsubnets？（）A.10.0.0.0/22issubnetted，1subnets D 10.4.0.0[90/20514560]via10.2.0.2，6w0d，serial0/1B.10.0.0.0/28issubnetted，1subnets D10.2.0.0[90/20514560]via10.2.0.2，6w0d，serial0/1C.10.0.0.0/22issubnetted，1subnets D10.0.0.0[90/20514560]via10.2.0.2，6w0d，serial0/1D.10.0.0.0/30issubnetted，1subnets D10.2.2.0[90/20514560]via10.2.0.2，6w0d，serial0/1E.10.0.0.0/28issubnetted，1subnets D10.4.4.0[90/20514560]via10.2.0.2，6w0d，serial0/1F.10.0.0.0/30issubnetted，1subnets D10.4.4.4[90/20514560]via10.2.0.2，6w0d，serial0/1
根据下图,图中两个设备是网络中仅有的CISCO设备,两个设备间的串行链路的掩码255.255.255.252,在下面的答案中,哪三个是正确的?() A.Manchester的串行链路的地址为10.1.1.1B.Manchester的串行链路的地址为10.1.1.2C.London路由器是CISCO2610D.London路由器是CISCO2611E.路由器Manchester的Serial0/0端口收到CDP信息F.路由器London的Serial0/0端口收到CDP信息
某路由器路由表如下:此时当该路由器从以太网口收到一个发往11.1.1.1主机的数据包时,路由器如何处理() A.丢掉B.从Serial0转发C.从Ethernet0转发D.从LoopBack0转发
Use the output from the router shown in the graphic above to determine which of the following are correct.() A. Router John uses a link-state routing protocol.B. Router John will receive routing updates on the Serial0/0 interface.C. Router John will receive routing updates on the Serial0/1 interface.D. Router John will send routing updates out the Serial0/0 interface.E. Router John will send routing updates out the FastEthernet0/0 interface.F. Router John will send routing updates out the Serial0/1 interface.
下列的配置路由器不会出现提示错误的是（）A、R1（config）#no shutdownB、R1（config）#interface Serial0/0/1C、R1（config）#ipv6 route fec0：dddd：/64Serial0/0/1D、R1（config）#ipv6 route fec0：bbbb：/64
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below: Gateway of last resort is 10.1.2.2 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0 C 10.1.2.0 is directly connected, Serial0/0 C 10.1.5.0 is directly connected, Serial0/1 C 10.1.6.0 is directly connected, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1 Based on the output above, if an administrator pings host 10.1.8.5 from host 10.1.6.100, how will the router TestkingA process the ICMP packets?（）A、The packets will be discarded.B、The packets will be routed out the S0/0 interface.C、The packets will be routed out the S0/1 interface.D、The packets will be routed out the Fa0/0 interface.E、The packets will be routed through the 10.1.2.2 gateway.
下面配置IPV6的默认路由正确的是（）A、R4（config-if）#ipv6 router：：/0 serial0/0/1B、R4（config）#ipv6 router：：/0 serial0/0/1C、R4（config）#ipv6 router：：serial0/0/1
Router# show interfaces serial 0/1 命令的输出显示了如下内容： Serial0/1 is down， line protocol is down. 线路协议为 down（关闭）的原因最可能是什么（）A、Serial0/1 为关闭状态B、路由器未连接电缆C、远程路由器正在使用 serial 0/0 接口D、尚未设置时钟频率
在Quidway路由器上已经配置了一个访问控制列表1，并且使能了防火墙。现在需要对所有通过Serial0接口进入的数据包使用规则1进行过滤。如下可以达到要求的是（）A、在全局模式配置：firewall 1 serial0 inB、在全局模式配置：access-group 1 serial0 outC、在Serial0的接口模式配置：access-group 1 inD、在Serial0的接口模式配置：access-group 1 outE、在Serial0的接口模式配置：ip access-group 1 inF、在Serial0的接口模式配置：ip access-group 1 out
两台空配置的MSR 路由器RTA、RTB 通过各自的Serial1/0 接口背靠背互连。在两台路由器上做如下配置： RTA： [RouterA-Serial1/0] link-protocol fr ietf [RouterA-Serial1/0] ip address 10.1.1.1 30 [RouterA-Seria11/0] fr map ip 10.1.1.2 30 RTB： [RouterB-Serial1/0] link-protocol fr ietf [RouterB-Serial1/0] interface serial0/0.1 [RouterB-Serial1/0.1] ip address 10.1.1.2 30 [RouterB-Serial1/0.1] fr map ip 10.1.1.1 30 路由器之间的物理链路良好，那么下面说法正确的是（）。A、两台路由器上都没有配置DLCI，在RTA 上不能ping 通RTBB、在RTA上不能ping通10.1.1.2C、在RTA上可以ping通10.1.1.2D、在上述配置中，如果仅将RTB上子接口serial0/0.1的类型改为P2MP，那么在RTA上不能ping通10.1.1.2E、在上述配置中，如果仅将RTB上子接口serial0/0.1的类型改为P2MP，那么在RTA上可以ping通10.1.1.2
在运行OSPF的Quidway路由器上，执行Show ip ospf interface serial0命令，发现接口的状态显示为point-to-point，则说明Serial0接口封装的一定是PPP协议。
一台路由器接口信息显示如下：Serial0/0currentstate：UPLineprotocolcurrentstate：DOWNPhysicallayerissynchronous，Baudrateis64000bpsInterfaceisDCE，CabletypeisV.35，ClockmodeisDCECLK那么该接口上可能封装或运行了哪种协议？（）A、PPPB、HDLCC、FrameRelayD、RIPE、以上答案都不正确
在Quidway路由器上已经配置了一个访问控制列表1，并且使能了防火墙。现在需要对所有通过Serial0接口进入的数据包使用规则1进行过滤。如下可以达到要求的是（）A、在全局模式配置：firewall1 serial0inB、在全局模式配置：access-group1 serial 0 outC、在Serial0的接口模式配置：access-group1 inD、在Serial0的接口模式配置：access-group1 outE、在Serial0的接口模式配置：ipaccess-group1 inF、在Serial0的接口模式配置：ipaccess-group1 out
此时当该路由器从以太网口收到一个发往10.1.1.1主机的数据包时，路由器如何处理（）A、从Serial0转发给2.2.2.1B、从Ethernet0转发给2.2.2.1C、从Serial0转发给目标主机D、从Ethernet0转发给目标主机
Refer to the exhibit. What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?（）A、The Serial0/0 interface is passing traffic.B、The DLCI 100 was dynamically allocated by the routerC、The Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP serverD、The DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloudE、The mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
Which line from the output of the show ip interface command indicates a layer 1 problem?（）A、Serial0/1 is up, line protocol is downB、Serial0/1 is down, line protocol is downC、Serial0/1 is up, line protocol is upD、Serial0/1 is administratively down, line protocol is down
The output of s how ip eigrp topology on Router R1 shows the following output, which is all the output related to subnet 10.11.1.0/24. How many feasible successor routes does R1 have for 10.11.1.0/24?（） P 10.11.1.0/24, 2 successors, FD is 2172419 via 10.1.1.2 (2172423/2 8167), Serial0/0/0.1 via 10.1.1.6 (2172423/28167), Serial0/0/0.2A、0B、1C、2D、3
单选题The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below: Gateway of last resort is 10.1.2.2 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0 C 10.1.2.0 is directly connected, Serial0/0 C 10.1.5.0 is directly connected, Serial0/1 C 10.1.6.0 is directly connected, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1 Based on the output above, if an administrator pings host 10.1.8.5 from host 10.1.6.100, how will the router TestkingA process the ICMP packets?（）AThe packets will be discarded.BThe packets will be routed out the S0/0 interface.CThe packets will be routed out the S0/1 interface.DThe packets will be routed out the Fa0/0 interface.EThe packets will be routed through the 10.1.2.2 gateway.
单选题Refer to the exhibit. What is the meaning of the term dynamic as displayed in the output of the show frame-relay map command shown?（）AThe Serial0/0 interface is passing traffic.BThe DLCI 100 was dynamically allocated by the routerCThe Serial0/0 interface acquired the IP address of 172.16.3.1 from a DHCP serverDThe DLCI 100 will be dynamically changed as required to adapt to changes in the Frame Relay cloudEThe mapping between DLCI 100 and the end station IP address 172.16.3.1 was learned through Inverse ARP
单选题Router# show interfaces serial 0/1 命令的输出显示了如下内容： Serial0/1 is down， line protocol is down. 线路协议为 down（关闭）的原因最可能是什么（）ASerial0/1 为关闭状态B路由器未连接电缆C远程路由器正在使用 serial 0/0 接口D尚未设置时钟频率