An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?()A. The switch that will share its VLAN configuration must be in VTP server mode.B. The switches must be in the same VTP domain.C. The switch that will share the VLAN information must be configured as the root bridge.D. The switches must be connected over VLAN trunks.E. The switches must be configured to use the same STP version.F. The switches must have VTP pruning activated.

An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?()

A. The switch that will share its VLAN configuration must be in VTP server mode.

B. The switches must be in the same VTP domain.

C. The switch that will share the VLAN information must be configured as the root bridge.

D. The switches must be connected over VLAN trunks.

E. The switches must be configured to use the same STP version.

F. The switches must have VTP pruning activated.


相关考题:

在Cisco Catalyst 3548以太网交换机上建立一个名为lib105的VLAN,下列正确的配置是______。A) Switch-3548#vlan 1 name lib 105Switch-3548#exitB) Switch-3548(vlan)#vlan 1 name lib 105Switch-3 548(vlan)#exitC) Switch-3548(vlan)#vlan 1000 name lib 105Switch3548(vlan)#exitD) Swimh-3548(vlan)#vlan 1002 name lib 105Switch-3548(vlan)#exitA.B.C.D.

You need to create a new VLAN on your Catalyst switch. This VLAN is to be named EZONEXAM. Which of the following need to be completed for the creation of this new VLAN? (Select all that apply)A. The EZONEXAM VLAN must be created.B. The desired ports must be added to the new EZONEXAM VLAN.C. The EZONEXAM VLAN must be added to all of the domains.D. The EZONEXAM VLAN must be named.E. An IP address must be configured for the EZONEXAM VLAN.F. None of the above. VLAN creations are automatic.

The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?()A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.

Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?() A. Switch(config-if)# vlan allB. Switch(config-if)# switchport trunk encapsulation dot1qC. Switch(config-if)# switchport access vlan allD. Switch(config-if)# switchport mode trunkE. Switch(config-if)# switchport access vlan 303

An administrator is unsuccessful in adding VLAN 50 to aswitch. While troubleshooting the problem, the administrator views the output of the show vtp status command, which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database?()A. Switch(config-if)# switchport access vlan 50B. Switch(vlan)# vtp serverC. Switch(config)# config-revision 20D. Switch(config)# vlan 50 name TechE. Switch(vlan)# vlan 50F. Switch(vlan)# switchport trunk vlan 50

A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch. Which of the following command will enable that?() A、interface vlan 100 ip access-group test inB、interface vlan 100 ip access-group testC、vlan access-map test 100D、vlan filter test vlan-list 100

Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?()A、Switch(config-if)# vlan allB、Switch(config-if)# switchport trunk encapsulation dot1qC、Switch(config-if)# switchport access vlan allD、Switch(config-if)# switchport mode trunkE、Switch(config-if)# switchport access vlan 303

You want to configure switch R1 to propagate VLAN information across the Company network  using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()A、VTP modeB、VTP passwordC、VTP revision numberD、VTP pruningE、VTP domain nameF、None of the other alternatives apply

The network administrator maps VLAN 10 through 20 to MST instance 2.  How will this information be propagated to all appropriate switches?()A、 Information will be carried in the RSTP BPDUs.B、 It will be propagated in VTP updates.C、 Information stored in the Forwarding Information Base and the switch will reply on query.  D、 Multiple Spanning Tree must be manually configured on the appropriate switches.

An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()A、The switch must be configured with an IP address,subnet mask,and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch port.F、The switch must be fully configured as an SNMP agent.

An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?()A、The switch that will share its VLAN configuration must be in VTP server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be connected over VLAN trunks.E、The switches must be configured to use the same STP version.F、The switches must have VTP pruning activated.

Given the output of the Floor3 switch, what statement describes the operation of this switch()。A、VTP is disabled on this switch.B、The switch can create, change, and delete VLANs.C、The switch learns VLAN information but does not save it to NVRAM.D、The switch can create VLANs locally but will not forward this information to other switches.E、The switch learns VLAN information and updates the local VLAN data base in NVRAM.

Which of the following is not information provided from an IP phone to a Catalyst switch using  CDP?()A、 device PoE requirementsB、 device IP addressC、 device voice VLAN IDD、 device platform

An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()A、The switch must be configured with an IP address, subnet mask, and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch

You need to create a new VLAN on your Catalyst switch. This VLAN is to be named TESTKING. Which of the following need to be completed for the creation of this new VLAN?()A、The TESTKING VLAN must be created.B、The desired ports must be added to the new TESTKING VLAN.C、The TESTKING VLAN must be added to all of the domains.D、The TESTKING VLAN must be named.E、An IP address must be configured for the TESTKING VLAN.F、None of the above. VLAN creations are automatic.

A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?()A、The switch that will share the VLAN information must be in the VTP Server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be configured to use the same VTP version.E、The switches must be configured to use the same STP version.F、The switches must be configured to use the same type of ID tagging.G、The switches must be connected over VLAN trunks.

By default, each port in a Cisco Catalyst switch is assigned to VLAN1. Which two recommendations are key to avoid unauthorized management access? ()A、Create an additional ACL to block the access to VLAN 1.B、Move the management VLAN to something other than default.C、Move all ports to another VLAN and deactivate the default VLAN.D、Limit the access in the switch using port security configuration.E、Use static VLAN in trunks and access ports to restrict connections.F、Shutdown all unused ports in the Catalyst switch.

You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.

单选题Which of the following is not information provided from an IP phone to a Catalyst switch using  CDP?()A device PoE requirementsB device IP addressC device voice VLAN IDD device platform

多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?()AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.

多选题You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()AThe switch name must match the workgroup name of the local network.BThe switch must be configured with an IP address and default gateway.CThe remote workstations must have access to the management VLAN of the switch.DCDP must be enabled on the switch so that it can be located by other devices on the network.

多选题By default, each port in a Cisco Catalyst switch is assigned to VLAN1. Which two recommendations are key to avoid unauthorized management access?()ACreate an additional ACL to block the access to VLAN 1.BMove the management VLAN to something other than default.CMove all ports to another VLAN and deactivate the default VLAN.DLimit the access in the switch using port security configuration.EUse static VLAN in trunks and access ports to restrict connections.FShutdown all unused ports in the Catalyst switch.

单选题A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch. Which of the following command will enable that?()Ainterface vlan 100 ip access-group test inBinterface vlan 100 ip access-group testCvlan access-map test 100Dvlan filter test vlan-list 100

单选题Given the output of the Floor3 switch, what statement describes the operation of this switch()。AVTP is disabled on this switch.BThe switch can create, change, and delete VLANs.CThe switch learns VLAN information but does not save it to NVRAM.DThe switch can create VLANs locally but will not forward this information to other switches.EThe switch learns VLAN information and updates the local VLAN data base in NVRAM.

单选题You want to configure switch R1 to propagate VLAN information across the Company network  using VTP. What must be configured on a Cisco switch in order to advertise VLAN information?()AVTP modeBVTP passwordCVTP revision numberDVTP pruningEVTP domain nameFNone of the other alternatives apply

多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()AThe switch must be configured with an IP address,subnet mask,and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch port.FThe switch must be fully configured as an SNMP agent.

单选题The network administrator maps VLAN 10 through 20 to MST instance 2.  How will this information be propagated to all appropriate switches?()A Information will be carried in the RSTP BPDUs.B It will be propagated in VTP updates.C Information stored in the Forwarding Information Base and the switch will reply on query.  D Multiple Spanning Tree must be manually configured on the appropriate switches.

多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()AThe switch must be configured with an IP address, subnet mask, and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch