下面用于在交换机中配置Trunk承载的VLAN的命令是( ) A、access vlan vlan-idB、port link-type trunkC、port trunk allow-pass vlanD、set port vlan vlan-id
下面用于在交换机中配置Trunk承载的VLAN的命令是( )
A、access vlan vlan-id
B、port link-type trunk
C、port trunk allow-pass vlan
D、set port vlan vlan-id
相关考题：
请填写以下Cisco 6500交换机STP配置命令的描述。set spantree enable[vlan] (1)set spantree fwddelay delay[vlan] (2)set spantree hello interval[vlan] (3)set spantree maxage agingtime[vlan] (4)set spantree portcost mod_num／port_num cost (5)
将交换机的access端口ethernet0/1加入VLAN4,可用如下方法配置（）。A.[Switch]vlan 4[Switch-vlan4]port ethernet0/1B.[Switch]vlan 4[Switch-Ethernet0/1]port access vlan 4C.[Switch]vlan 4[Switch-vlan4]port accesse thernet0/1D.[Switch]vlan 4[Switch-Ethernet0/1]port access vlan pvid 4[Huawei]vlan 3500[Huawei-Gigabit Ethernet0/0/1]disth interface Gigabit Ethernet0/0/1 port link-type access portdefault vlan 3500
某台华为交换机做了如下配置：[SWD]interface ethernet1/0/1[SWD-Ethernet1/0/1]port link-type hybrid[SWD-Ethernet1/0/1]port hybrid untagged vlan 3[SWD-Ethernet1/0/1]port vlan-stacking vlan 200 to 300 stack-vlan 3 [SWD]interface ethernet 1/0/1[SWD-Ethernet1/0/1]qinq protocol 0x9100关于此配置的说明不正确的是（）A.port link-type hybrid是配置接口类型为hybrid，灵活QinQ的接入端口类型可以配置为trunk或hybrid，根据具体情况而定B.Ethernet1/0/1接口在发送帧时会将帧中的vlan 3 Tag剥离C.在VLAN 200到300的用户VLAN上剥离VLAN 3TagD.qinq protocol 0x9100命令是修改TPID字段取值
如图所示，LAN A和LAN B为用户网络，通过SWB和SWD连接到ISP网络，SWA和SWE为用户侧交换机，都下挂有VLAN200到300的私网用户。SWB连接SWA的接口Ethernet1/0/1、SWD连接SWE的接口Ethernet1/0/1都为QinQ接入端口，属于VLAN3。在交换机SWB的端口Ethernet 1/0/2上，下面基于端口的QinQ配置（为端口进入的业务添加外层VLAN3）正确的是（）A.port link-type trunkB.port link-type dot1q-tunnelC.port trunk allow-pass vlan 3D.port trunk allow-pass vlan 200 to 300
下面是一段关于交换机端口的配置,针对如下配置说法正确的是()port link－type hybrid port hybrid pvid vlan2port hybrid untagged vlan 2 port hybrid tagged vlan3 A.该端口的默认VLAN是VLAN 2B.port hybrid tagged vlan 3命令用来配置Hybrid类型接口所属的VLAN，这些VLAN的帧以Untagged方式通过接口C.por thybrid untagged vlan 2命令用来配置Hybrid类型接口所属的VLAN，这些VLAN的帧以Tagged方式通过接口D.以上说法都正确
A.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/3 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE TRUNK [SWITCHA-GIGABITETHERNET1/0/3] PORT TRUNK ALLOW-PASS VLAN 2 3 B.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/1 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE TRUNK [SWITCHA-GIGABITETHERNET1/0/3] PORT TRUNK ALLOW-PASS VLAN 2 3 C.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/1 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE ACCESS [SWITCHA-GIGABITETHERNET1/0/3] PORT DEFAULT VLAN 2 3 D.[SWITCHA] INTERFACE GIGABITETHERNET 1/0/3 [SWITCHA-GIGABITETHERNET1/0/3] PORT LINK-TYPE ACCESS [SWITCHA-GIGABITETHERNET1/0/3] PORT DEFAULT VLAN 2 3
某台华为交换机做了如下配置：[HUAWEI]interface ethernet 1/0/1[HUAWEI-Ethernet1/0/1]port link-type hybrid[HUAWEI-Ethernet1/0/1]port hybrid untagged vlan 3关于此配置的说明正确的是（ ） A.port link-type hybrid 是配置接口类型为hybridB.Ethernet1/0/1 接口在发送帧时会将帧中的vlan 3 Tag 标记为untagC.VLAN 上剥离VLAN 3 的unTag标记D.Ethernet1/0/1 接口在接收帧时会将帧中的vlan 3 Tag 剥离。
交换机如何将接口设置为TAG VLAN模式？（）A、switchport mode tagB、switchport mode trunkC、trunk onD、set port trunk on
中兴ZXCTN设备在进行初始化时，以下哪个选项命令是不属于MCC监控命令的脚本（）A、snmp-server packetsize 8192B、interface vlan 3001；ip address 139.9.1.6255.255.255.252；exitC、vlan3001；exitD、interface xgei_9/1；mcc-vlanid3001；switchport mode trunk；switch port trunk vlan 3001；switch port trunk native vlan 3001；exit
要想让S3026透传vlan100，必须要在S3026上配置哪些命令（）。A、vlan 100B、port link-type trunkC、port trunk permit vlan 100D、port trunk pvid vlan 1
You are troubleshooting a Catalyst 5000 trunk in the network. What should you do if there’s adisagreement about the VLANs configured to use the trunk？（）A、Reload the active VLAN configurationB、Clear the affected port and bring it up againC、Explicitly set the trunk for the VLAN to be onD、Remove all the VLANs set
A Cisco switch has this configuration for a port channel connecting to an ESXi using dual NICs and is intended for use with an N1Kv. Interface fastethernet 1/10 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface fastethernet 1/11 Switchport mode trunk Switchport trunk allowed vlan all Channel-group 10 mode on No shut Interface port-channel 10 Switchport mode trunk Switchport allowed vlan all No shut Which Port Channel configuration must be used on the Nexus 1000v port-profile？（）A、 MAC pinningB、 Cisco Discovery Protocol pinningC、 Mode OnD、 Mode ActiveE、 No port channel configuration
n the case of Ethernet transport， which two types of attachment circuits does L2TPv3 support？ （）A、port tunneling on the Ethernet subinterfaceB、VLAN tunneling on the Ethernet trunkC、port tunneling on the Ethernet interfaceD、VLAN tunneling on the Ethernet VLAN subinterfaceE、port tunneling on the Ethernet trunk
Which command alone will disable trunking on a Layer 2 switch port？（）A、no switchport trunk native vlan vlan-idB、switchport nonegotiateC、no switchport mode dynamic desirableD、switchport mode access
When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?（）A、BlockingB、AutoC、DesirableD、OnE、TransparentF、Learning
Which are valid modes for a switch port used as a VLAN trunk? （）A、transparentB、autoC、onD、desirable
单选题Which command alone will disable trunking on a Layer 2 switch port？（）Ano switchport trunk native vlan vlan-idBswitchport nonegotiateCno switchport mode dynamic desirableDswitchport mode access
单选题下面是一段关于交换机端口的配置，针对如下配置说法正确的是（）port link-type hybrid port hybrid pvid vlan2port hybrid untagged vlan 2 port hybrid tagged vlan3A该端口的默认VLAN是VLAN 2Bport hybrid tagged vlan 3命令用来配置Hybrid类型接口所属的VLAN，这些VLAN的帧以Untagged方式通过接口Cpor thybrid untagged vlan 2命令用来配置Hybrid类型接口所属的VLAN，这些VLAN的帧以Tagged方式通过接口D以上说法都正确
单选题某台华为交换机做了如下配置：[SWD]interface ethernet1/0/1[SWD-Ethernet1/0/1]port link-type hybrid[SWD-Ethernet1/0/1]port hybrid untagged vlan 3[SWD-Ethernet1/0/1]port vlan-stacking vlan 200 to 300 stack-vlan 3 [SWD]interface ethernet 1/0/1[SWD-Ethernet1/0/1]qinq protocol 0x9100关于此配置的说明不正确的是（）Aport link-type hybrid是配置接口类型为hybrid，灵活QinQ的接入端口类型可以配置为trunk或hybrid，根据具体情况而定BEthernet1/0/1接口在发送帧时会将帧中的vlan 3 Tag剥离C在VLAN 200到300的用户VLAN上剥离VLAN 3TagDqinq protocol 0x9100命令是修改TPID字段取值
多选题When a switch port is used as a VLAN trunk, which of the following trunk modes are valid?（）ABlockingBAutoCDesirableDOnETransparentFLearning
判断题通过以下命令 Port link-type trunk Port trunk permit vlan 10 可以将交换机的端口设置为 Trunk 端口，允许 VLAN10 报文通过，其他的拒绝。A对B错