What is required for proper implementation of jumbo frame support on a Cisco Nexus 2000 Series Fabric Extender？（） A、 The interface configured as FEX fabric requires the MTU to be set to jumbo.B、 The service policy must be applied to the system QoS.C、 The device defaults to jumbo frame support； no changes are required.D、 The switchport in the FEX interface must be set to MTU 9216.
What is required for proper implementation of jumbo frame support on a Cisco Nexus 2000 Series Fabric Extender？（）
- A、 The interface configured as FEX fabric requires the MTU to be set to jumbo.
- B、 The service policy must be applied to the system QoS.
- C、 The device defaults to jumbo frame support； no changes are required.
- D、 The switchport in the FEX interface must be set to MTU 9216.
相关考题：
Refer to the exhibit. What is required to complete the IPv6 routing configurations shown?() A. Interface authentication must be configuredB. The routing processes must be configured with an area IDC. IP unicast routing must be enabledD. IPv4 ad dresses must be applied to the interfaces
What is the appliance port used to connect to in a Cisco Unified Computing System？（）A、 Fibre Channel storageB、 UCS C-Series serversC、 NFS storageD、 UCS chassisE、 Other fabric interconnect
Which of the following is not an essential prerequisite for AutoQoS to be correctly applied to an interface（）A、The interface must be configured as a Multilink PPP interface.B、The correct bandwidth should be configured on the interface.C、A QoS policy must not be currently attached to the interface.D、CEF must be enableE、AutoQoS must be enabled globally before it can be enabled on the interface.F、An IP address must be configured on the interface if its speed is equal to or less than 768 kbps.
Enabling jumbo frame support on a Cisco Nexus 5500 Switch can be done through which method？（） A、 changing the default policy map from a default MTU of 1500 to 9216B、 using the command system jumbomtu 9216C、 using the command interface MTU 9216D、 configuring the default Ethernet system class to an MTU of 9216 with a new network QoS policy map
Which statement ab0ut VLANs in a Cisco UCS is true?（）A、Fabric interconnect can never participate in VTPB、Fabric interconnect supports ISL and 802.1Q trunkingC、The supported range of VLANs is auto-configured by UCSD、VLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
The hardware and software configurations for vPC+ are similar to that of traditional vPC. What are the differences in the configuration of vPC+？ （）A、 FabricPath switch ID must be configured under the vPC domain.B、 Virtual switch ID of vPC+ must be configured under FabricPath domain.C、 On Cisco Nexus 7000 Series Switch， F1 interfaces must be used as the vPC+ peer links.D、 The vPC+ peer link must be configured as a Cisco FabricPath core port （switchport mode fabricpath）.E、 FabricPath subswitch ID must be configured under the vPC domain.
What must be configured on the Cisco Unity Express host router prior to installation of the CUE module?（）A、Set up the Network Time Protocol server. B、Install the files needed to run the web-based GUI. C、Set up routing and IP addressing on the service module and the interface service engine. D、Configure a session initiation protocol dial peer for connecting calls to the voice mail and Auto Attendant features.
On the Cisco Nexus 7000 Series Switch， Control Plane Policing is enforced on which component？（）A、 The supervisor module enforces CoPP before out-of-policy traffic reaches the CPUB、 The fabric modules enforce CoPP in the fabric before out-of-policy traffic reaches the CPU C、 The linecards enforce CoPP locally before out-of-policy traffic reaches the CPUD、 The egress virtual output queue enforces CoPP locally before out-of-policy traffic reaches the CPU
Which two statements about SAN port channels configured on Cisco Nexus 5000 Series switches are true？ （） A、 The bring up protocol automatically detects and overrides any misconfiguration.B、 You can manually configure channel groups， or they can be automatically created.C、 Changes in configuration to the SAN port channel interface must also be made to all members of the channel group.D、 The port channel protocol uses the exchange fabric parameters command to communicate across peer ports in an ISL.E、 The port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.
Which statements are true regarding the Cisco UCS fabric failover feature？ （）A、 FabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.B、 Gratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover. C、 Fabric failover can be used on vNICs and vHBAs.D、 Fabric failover is configured as part of the service profile.E、 Fabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
Which statement about Cisco Unified Fabric switches is correct？ （） A、 The Nexus 5000 family of switches does not support vPC when running in either NPV or FCoE NPV mode.B、 The MDS 9100 family of switches is an excellent design choice as a Unified Fabric edge switch. C、 The Nexus 7000 Series Switches can support the NPIV mode of operation， but cannot function as a complete Fibre Channel Forwarder.D、 The Nexus 7000 Series Switches cannot support advanced Cisco Fibre Channel features such as IVR.E、 The MDS family of Cisco Unified Fabric switches supports both the Fibre Channel Forwarder and Fibre Channel Bridge functions.
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）A、 A· unique vEthernet interface will be created on Fabric A· and Fabric B·B、 A· vEthernet interface will be created only on Fabric A·C、 A· vEthernet interface will be created on Fabric A·， and move across to Fabric B· in the event of failureD、 Fabric B· will learn the vEthernet interface from Fabric A· through a GARP E· The same vEthernet interface will be created on Fabric A· and Fabric B·
Which two Fibre Channel features are not supported in Cisco Nexus 5500 and Nexus 5000 platforms？ （）A、 port securityB、 fabric bindingC、 IVRD、 port trackingE、 FICON
Which statement about PPPoA configuration is correct？（）A、The dsl operating-mode auto command is required if the default mode has been changedB、The ip mtu 1496 command must be applied on the dialer interfaceC、The encapsulation ppp command is requiredD、The ip mtu 1492 command must be applied on the dialer interface
Which two statements regarding SNMP monitoring of a UCS system are correct?（）A、SNMP v3 is supportedB、includes same MIBs as the Cisco Nexus7000C、does not provides MIBs downstream of the fabric interconnectD、includes same MIBs as the Cisco Nexus2000
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）A、 The fabric interconnects must be in end-host mode.B、 A pin group must be configured on the server tab in Cisco UCS Manager.C、 In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.D、 Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.E、 Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）A、 Cisco UCS Manager 1.3（xx） or later and a pair of Nexus 2248 FEXesB、 Cisco UCS Manager 2.0（2xx） or later and a pair of Nexus 2232 FEXesC、 Two Cisco UCS 6100 Series or 6200 Series fabric interconnectsD、 Two RJ45 Ethernet cablesE、 The fabric interconnects must be in end-host mode
Company.com with an EtherChannel implementation is considering an HACMP solution. What considerations must be addressed in planning this configuration？（） A、 Hardware address takeover must be configured.B、 IPAT via IP aliasing is required for EtherChannel.C、 EtherChannel must be defined as a separate network.D、 HACMP does not support the fallover of EtherChannel.
An IBM System Storage DS8300 is being installed at a global corporation’s headquarter location. The storage must be available worldwide. A great deal of coordination is required to schedule this implementation across the corporation. Who is best positioned to fill the role of implementation resource coordinator（）A、IBM Service Support RepresentativeB、IBM Advanced Technical Support RepresentativeC、IBM Field Technical Support RepresentativeD、customer IT Manager
单选题Enabling jumbo frame support on a Cisco Nexus 5500 Switch can be done through which method？（）A changing the default policy map from a default MTU of 1500 to 9216B using the command system jumbomtu 9216C using the command interface MTU 9216D configuring the default Ethernet system class to an MTU of 9216 with a new network QoS policy map
多选题Which statements are true regarding the Cisco UCS fabric failover feature？ （）AFabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.BGratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover.CFabric failover can be used on vNICs and vHBAs.DFabric failover is configured as part of the service profile.EFabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
单选题What is required for proper implementation of jumbo frame support on a Cisco Nexus 2000 Series Fabric Extender？（）A The interface configured as FEX fabric requires the MTU to be set to jumbo.B The service policy must be applied to the system QoS.C The device defaults to jumbo frame support； no changes are required.D The switchport in the FEX interface must be set to MTU 9216.
单选题What is the appliance port used to connect to in a Cisco Unified Computing System？（）A Fibre Channel storageB UCS C-Series serversC NFS storageD UCS chassisE Other fabric interconnect
单选题An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）A A· unique vEthernet interface will be created on Fabric A· and Fabric B·B A· vEthernet interface will be created only on Fabric A·C A· vEthernet interface will be created on Fabric A·， and move across to Fabric B· in the event of failureD Fabric B· will learn the vEthernet interface from Fabric A· through a GARP E· The same vEthernet interface will be created on Fabric A· and Fabric B·
多选题Which two statements about SAN port channels configured on Cisco Nexus 5000 Series switches are true？ （）AThe bring up protocol automatically detects and overrides any misconfiguration.BYou can manually configure channel groups， or they can be automatically created.CChanges in configuration to the SAN port channel interface must also be made to all members of the channel group.DThe port channel protocol uses the exchange fabric parameters command to communicate across peer ports in an ISL.EThe port channel protocol ensures that a set of ports is eligible to be part of the same SAN port channel.
多选题What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）ACisco UCS Manager 1.3（xx） or later and a pair of Nexus 2248 FEXesBCisco UCS Manager 2.0（2xx） or later and a pair of Nexus 2232 FEXesCTwo Cisco UCS 6100 Series or 6200 Series fabric interconnectsDTwo RJ45 Ethernet cablesEThe fabric interconnects must be in end-host mode
单选题Which statement about PPPoA configuration is correct？（）AThe dsl operating-mode auto command is required if the default mode has been changedBThe ip mtu 1496 command must be applied on the dialer interfaceCThe encapsulation ppp command is requiredDThe ip mtu 1492 command must be applied on the dialer interface