单选题What is the role of route preference?（）AIt is used as a tie breaker when the same prefix is available through multiple sourcesBIt is used to determine which routes to accept into the routing tableCIt is used to select the best route between multiple equal-cost pathsDIt is used to select which routing table to use for forwarding
单选题
What is the role of route preference?（）
A
It is used as a tie breaker when the same prefix is available through multiple sources
B
It is used to determine which routes to accept into the routing table
C
It is used to select the best route between multiple equal-cost paths
D
It is used to select which routing table to use for forwarding
参考解析
解析：
暂无解析
相关考题：
You are modifying the default route preference under the [edit protocols] hierarchy. In which two routing information sources can you change the default preference value?() A. localB. OSPFC. directD. BGP
What happens to the 66.66.66／24 route when it is evaluated by this policy? () A. The route does not match this policy.B. The route is rejected.C. The route is accepted.D. The route is accepted, then rejected.
Which BGP route selection criterion is superior?() A. lowest MEDB. highest weightC. lowest local preferenceD. highest local preference
Referring to the exhibit, if the static route with prefix 10.1.1.0／24 is evaluated against the routing policy, which preference value will be set?() A. The preference will be 6.B. The preference will be 7.C. The preference will be 8.D. The preference will be the default for static routes.
Which two statements are true regarding route preference?() A. Lower preference values are more preferred than higher preference values.B. You can modify the default preference values for any of the routing information sources.C. By default, a static route is more preferred than a RIP route.D. A static route is always preferred over a direct route.
You are moddifying the default route preference under the [edit protocols] hierarchy. In which two routing information sources can you change the default preference value?() A.localB.OSPFC.directD.BGP
What is the order of preference for these commands when all of them are applied to one neighbor in theBGP inbound filter direction？（）A、prefix-list， route-map， filter-list， distribute listB、route-map， filter-list， prefix-list， distribute-listC、route-map， distribute-list， prefix-list， filter-listD、filter-list， prefix list， route-map， distribute listE、distribute list， prefix-list， route-map， fitter list
Router R1 learns two routes with BGP for prefix 200.1.0.0/16. Comparing the two routes, route 1 has a shorter AS_Path Length, smaller MED, the same Weight, and smaller Local PreferencE. Which of the following is true about Router R1's choice of best path for this prefix?（）A、Route 1 is the best route.B、Route 2 is the best route.C、The routes tie as best, but one will be picked to be placed in the routing table based on tiebreakers .D、Neither route is considered best.
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?（）A、To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50B、Th e router will prefer the shortest autonomous system pathC、If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MEDD、The router will prefer the route with the lower MED
What is correct regarding the configuration shown below?（） （1）static route 0.0.0.0/0 （2）qualified-next-hop 172.30.25.1 preference 7 （3）next-hop 172.30.25.5A、The next-hop 172.30.25.1 is selected because the address has the lowest value.B、The next-hop 172.30.25.1 is selected because it is listed first.C、The next-hop 172.30.25.1 is selected because it is the lowest protocol preference.D、The next-hop 172.30.25.5 is selected because it is the lowest protocol preference.
When you display the routing table by entering the show route command, what does the* indicate?（）A、The route is a direct route.B、The route was selected as active.C、The route is a default route.D、The route was learned using a dynamic routing protocol.
What is the role of route preference?（）A、It is used to determine which route should become active.B、It is used to select which routing table to use for forwarding.C、It is used to determine what routes to accept into the routing table.D、It is used to select the best route between multiple equal cost paths.
What is the role of route preference?（）A、It is used as a tie breaker when the same prefix is available through multiple sourcesB、It is used to determine which routes to accept into the routing tableC、It is used to select the best route between multiple equal-cost pathsD、It is used to select which routing table to use for forwarding
单选题What is the role of route preference?（）AIt is used to determine which route should become active.BIt is used to select which routing table to use for forwarding.CIt is used to determine what routes to accept into the routing table.DIt is used to select the best route between multiple equal cost paths.
单选题What is the order of preference for these commands when all of them are applied to one neighbor in theBGP inbound filter direction？（）Aprefix-list， route-map， filter-list， distribute listBroute-map， filter-list， prefix-list， distribute-listCroute-map， distribute-list， prefix-list， filter-listDfilter-list， prefix list， route-map， distribute listEdistribute list， prefix-list， route-map， fitter list
单选题A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values. Which statement is true about how BGP would select the best path?（）ATo influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50BTh e router will prefer the shortest autonomous system pathCIf the command bgp always - compare - med has been given, then the router will prefer the route with the highest MEDDThe router will prefer the route with the lower MED
多选题Which two statements are true regarding route preference?（）ALower preference values are more preferred than higher preference values.BYou can modify the default preference values for any of the routing information sources.CBy default, a static route is more preferred than a RIP route.DA static route is always preferred over a direct route.
单选题Which BGP route selection criterion is superior?（）Alowest MEDBhighest weightClowest local preferenceDhighest local preference
单选题What is correct regarding the configuration shown below?（） （1）static route 0.0.0.0/0 （2）qualified-next-hop 172.30.25.1 preference 7 （3）next-hop 172.30.25.5AThe next-hop 172.30.25.1 is selected because the address has the lowest value.BThe next-hop 172.30.25.1 is selected because it is listed first.CThe next-hop 172.30.25.1 is selected because it is the lowest protocol preference.DThe next-hop 172.30.25.5 is selected because it is the lowest protocol preference.
单选题What is the role of route preference?（）AIt is used as a tiebreaker when the same prefix is available through multiple protocols.BIt is used to determine the preferred path to a given destination.CIt is used to select the best route between multiple equal-cost paths.DIt is used to select which routing table to use for forwarding.
多选题You are modifying the default route preference under the [edit protocols] hierarchy. In which two routing information sources can you change the default preference value?（）AlocalBOSPFCdirectDBGP
单选题What is the role of route preference?（）AIt is used as a tie breaker when the same prefix is available through multiple sourcesBIt is used to determine which routes to accept into the routing tableCIt is used to select the best route between multiple equal-cost pathsDIt is used to select which routing table to use for forwarding