单选题Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）ALACPBPAgPCMCPC
单选题
Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）
A
LACP
B
PAgP
C
MCPC
参考解析
解析：
暂无解析
相关考题：
What is the appliance port used to connect to in a Cisco Unified Computing System？（）A、 Fibre Channel storageB、 UCS C-Series serversC、 NFS storageD、 UCS chassisE、 Other fabric interconnect
Which protocol does the UCS Fabric Interconnect support on port channel uplinks?（）A、LACPB、PAgPC、MCPC
Which statement ab0ut VLANs in a Cisco UCS is true?（）A、Fabric interconnect can never participate in VTPB、Fabric interconnect supports ISL and 802.1Q trunkingC、The supported range of VLANs is auto-configured by UCSD、VLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
The cluster IP address of the UCS Fabric interconnects is used to access which three entities? （）A、CMCB、CLIC、APID、VSME、UI
Which components of the UCS solution include beacon LEDs?（）A、monitorsB、fabric interconnectC、bladesD、expansion modulesE、chassis
What is the use of an "all configuration" backup in Cisco UCS？（）A、 Can be used to migrate from a 6120 to a 6140 and retain the same service profilesB、 Can only be used on the fabric interconnect on which it was createdC、 Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster informationD、 Can be used to match firmware versions between 6120 and 6140 during a migration
Which two content-filtering features does FTP support?（） (Choose two.)A、block extension listB、block MIME typeC、protocol command listD、notifications-options
You are configuring an 802.1Q trunk between a Layer 2 switch and a firewall. You read in the documentation that the best way to set up a trunk is to set the port as dynamic desirable. The trunk is not coming up. Which one of these options would be a valid explanation？ （）A、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode ONB、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode to OFFC、The firewall does not support Cisco Discovery Protocol. You should set the switchport trunk mode asauto.D、The firewall does not support DTP. You should set the switchport trunk mode to ON
Which authentication protocol does H-REAP AP local authentication support in version 5.2?（）A、EAP-TLSB、EAP-PEAPC、EAP-LEAPD、EAP-TTLS
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）A、 Uplink Ethernet ports or border portsB、 Appliance portsC、 Server portsD、 Fabric portsE、 Backplane portsF、 vEth interfacesG、 A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
Which statements are true regarding the Cisco UCS fabric failover feature？ （）A、 FabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.B、 Gratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover. C、 Fabric failover can be used on vNICs and vHBAs.D、 Fabric failover is configured as part of the service profile.E、 Fabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）A、 The fabric interconnect is in the end-host mode， and all uplink ports have failed.B、 The server port to which the adapter is pinned has failed.C、 A transient error has caused the link to fail.D、 The fabric interconnect is in the switch mode， and all uplink ports have failed.E、 The link for a network-facing host interface is missing.
Where are SAN Port Channel is created in UCS Manager？（）A、 Under the Admin tab on the FIB、 Under the Server tab in the service profileC、 Under the SAN tab on each VSAND、 Under the Admin tab on the chassisE、 Under the SAN tab on the Fabric Interconnect
Which two statements regarding SNMP monitoring of a UCS system are correct?（）A、SNMP v3 is supportedB、includes same MIBs as the Cisco Nexus7000C、does not provides MIBs downstream of the fabric interconnectD、includes same MIBs as the Cisco Nexus2000
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）A、 The fabric interconnects must be in end-host mode.B、 A pin group must be configured on the server tab in Cisco UCS Manager.C、 In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.D、 Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.E、 Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）A、 During the initial configuration from the consoleB、 Once the basic configuration has been appliedC、 To restore the configuration on a secondary fabric interconnectD、 To upgrade the firmware on a replacement fabric interconnect
Which two aspects of a UCS solution enable fast response to growth requirements in the data center?（）A、UCS ManagerB、fabric interconnectC、service profilesD、expansion modulesE、virtual interface cards
多选题Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）AThe fabric interconnect is in the end-host mode， and all uplink ports have failed.BThe server port to which the adapter is pinned has failed.CA transient error has caused the link to fail.DThe fabric interconnect is in the switch mode， and all uplink ports have failed.EThe link for a network-facing host interface is missing.
单选题When will an "all configuration" backup be imported into the Cisco UCS Manager？（）A During the initial configuration from the consoleB Once the basic configuration has been appliedC To restore the configuration on a secondary fabric interconnectD To upgrade the firmware on a replacement fabric interconnect
多选题Which statements are true regarding the Cisco UCS fabric failover feature？ （）AFabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.BGratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover.CFabric failover can be used on vNICs and vHBAs.DFabric failover is configured as part of the service profile.EFabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
单选题Where are SAN Port Channel is created in UCS Manager？（）A Under the Admin tab on the FIB Under the Server tab in the service profileC Under the SAN tab on each VSAND Under the Admin tab on the chassisE Under the SAN tab on the Fabric Interconnect
单选题Which statement ab0ut VLANs in a Cisco UCS is true?（）AFabric interconnect can never participate in VTPBFabric interconnect supports ISL and 802.1Q trunkingCThe supported range of VLANs is auto-configured by UCSDVLANs are configured through the Cisco UCS manager. （fabric interconnect may be set up in switch mode）
单选题What is the use of an "all configuration" backup in Cisco UCS？（）A Can be used to migrate from a 6120 to a 6140 and retain the same service profilesB Can only be used on the fabric interconnect on which it was createdC Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster informationD Can be used to match firmware versions between 6120 and 6140 during a migration
多选题A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）AUplink Ethernet ports or border portsBAppliance portsCServer portsDFabric portsEBackplane portsFvEth interfacesGA Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
多选题The cluster IP address of the UCS Fabric interconnects is used to access which three entities? （）ACMCBCLICAPIDVSMEUI
单选题Which authentication protocol does H-REAP AP local authentication support in version 5.2?（）AEAP-TLSBEAP-PEAPCEAP-LEAPDEAP-TTLS
单选题What is the appliance port used to connect to in a Cisco Unified Computing System？（）A Fibre Channel storageB UCS C-Series serversC NFS storageD UCS chassisE Other fabric interconnect