单选题Routers A and B have an OC12c and a GE link between them and are running OSPF over both ofthese links. Which statement is correct, assuming the default JUNOS software OSPF metric calculation?（）AThere are two equal cost paths betweena and b.BThege link is the preferred path betweena and b.CThe oc12c link is the preferred path betweena and b.DManual metric assignment must be configured to determine the outcome
单选题
Routers A and B have an OC12c and a GE link between them and are running OSPF over both ofthese links. Which statement is correct, assuming the default JUNOS software OSPF metric calculation?（）
A
There are two equal cost paths between a and b.
B
The ge link is the preferred path between a and b.
C
The oc12c link is the preferred path between a and b.
D
Manual metric assignment must be configured to determine the outcome
参考解析
解析：
暂无解析
相关考题：
You are running OSPF between two ERX Edge Routers across an OC－12c link with HDLC encapsulation.How many designated routers are present for this link?() A.0B.1C.2D.3
Process OSPF 1 is redistributing routes from process OSPF 2. Which of the following methods may be used to set the metrics of the redistributed routes?() A. Let the metrics default.B. Use each redistributed route‘s OSPF metric using the redistribute command‘s metric transparent keywords.C. Set the metric using the default - metric router subcommand.D. Redistribution is not allowed between two OSPF p rocesses.
Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）A. Redistribute connected interfaces on router B and router CB. Set the maximum nu mber of equal cost paths to1 in all routersC. When redistributing EIGRP into OSPF, set the external metric type to type E1D. Adjust the default metrics in router B and router C so that the values are different in each routerE. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol
How will router A choose a path to the 10.1.2.0／24 network when different routing protocols are configured (Choose three.)()。 A.If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.B.If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.C.If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.D.If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.E.If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.F.If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.
If the OSPF protocol is used to connect customer edge （CE） routers to service provider edge（PE） routers in the VPN backbone， which two options best describe the use of SHAM links？（）A、A sham-link is created between any twoo VPN sites that belong to the same OSPF area and share an OSPF backdoor linkB、A sham-link is seen as an intra-area link between PE routers，an OSPF adjacency is created and data base is exchangedC、A SHAM link is created between two directly connected PE routers so that it is preferred over the low speed backdoor doorD、A SHAM link is part of OSPF network of MPLS-VPN provider
Which statement is correct about an OSPF sham-link？（）A、A sham-link is a logical link between PE routers that provides an OSPF adjacency between the PE routers and forwards customer traffic across it.B、A sham-link is a logical link between PE routers that provides an OSPF adjacency between the PE routers and carries OSPF LSAs.C、A sham-link is a logical link between PE routers that carries OSPF LSAs and forwards customer traffic across it.D、A sham-link is a point-to-multipoint link that provides an OSPF adjacency between the PE routers and carries OSPF LSAs.E、A sham-link is a point-to-multipoint link that provides an OSPF adjacency between the PE routers and forwards customer traffic across it.
You have two EBGP peers connected via two parallel serial lines. What should you do to be able to load-balance between two EBGP speakers over the parallel serial lines in both directions？ （）A、nothing，BGP automatically load-balances the traffic between different autonomous systems on all available linksB、peer between the eBGP speaker’s loopbacks， configuring eBGP multihop as required， and use an IGP to load-share between the two equal-cost paths between the loopback addressesC、configure a loopback as update source for both EBGP peers and have on each AS an IGP to introduce two equal-cost paths to reach the EBGP peer loopback address；it is also necessary to use the next-hop-self commandD、use the ebgp-load-balance command on the neighbor statement on both sidesE、configure a loopback as update source for both EBGP peers and have on each AS an IGP to introduce two equal-cost paths to reach the peer loopback address；it is also necessary to use the ebgp-multihop and next-hop-self commands
Which two statements are correct regarding default protocol preference values?（）A、RIP is preferred over OSPF external routes.B、Direct, local, and static routes have the same preference value.C、OSPF's preference value is lower than BGP.D、OSPF has a single preference value for both internal and external routes.
Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）A、set interfaces ge-0/3/0 unit 0 metric 10B、set protocols ospf reference-bandwidth 10gC、set interfaces ge-0/3/0 unit bandwidth 10gD、set protocols ospf area 0 interface ge-0/3/0 metric 10E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
You are running OSPF between two ERX Edge Routers across an OC-12c link with HDLC encapsulation. How many designated routers are present for this link?（）A、0B、1C、2D、3
Which two statements are correct regarding the default protocol preference values? （）A、RIP is preferred over OSPF external routesB、Direct, local and static routes have the same preference valueC、OSPF's preference value is lower than BGPD、OSPF has a single preference value for both internal and external routes
Which two statements are correct regarding default protocol preference values?（）A、OSPF has a single preference value for both internal and external routes.B、RIP is preferred over OSPF external routes.C、Direct, local, and static routes have the same preference value.D、OSPF's preference value is lower than BGP (both IBGP and EBGP).
Which two statements are correct regarding default protocol preference values?（）A、OSPF internal routes have a lower preference than static routes.B、Both direct and local routes have the same preference value.C、OSPF's preference value is lower than BGP.D、OSPF has a single preference value for both internal and external routes.
Routers A and B have an OC12c and a GE link between them and are running OSPF over both of these links.Which item is correct， assuming the default JUNOS software OSPF metric calculation？（）A、There are two equal cost paths between A and BB、The GE link is the preferred path between A and BC、The OC12c link is the preferred path between A and BD、Manual metric assignment must be configured to determine the outcome.
Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）A、set interfaces ge-0/3/0 unit 0 metric 10B、set protocols ospf reference-bandwidth 10gC、set interfaces ge-0/3/0 unit 0 bandwidth 10gD、set protocols ospf area 0 interface ge-0/3/0 metric 10E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
Routers A and B have an OC12c and a GE link between them and are running OSPF over both ofthese links. Which statement is correct, assuming the default JUNOS software OSPF metric calculation?（）A、There are two equal cost paths betweena and b.B、Thege link is the preferred path betweena and b.C、The oc12c link is the preferred path betweena and b.D、Manual metric assignment must be configured to determine the outcome
单选题You are running OSPF between two ERX Edge Routers across an OC-12c link with HDLC encapsulation. How many designated routers are present for this link?（）A0B1C2D3
多选题If the OSPF protocol is used to connect customer edge （CE） routers to service provider edge（PE） routers in the VPN backbone， which two options best describe the use of SHAM links？（）AA sham-link is created between any twoo VPN sites that belong to the same OSPF area and share an OSPF backdoor linkBA sham-link is seen as an intra-area link between PE routers，an OSPF adjacency is created and data base is exchangedCA SHAM link is created between two directly connected PE routers so that it is preferred over the low speed backdoor doorDA SHAM link is part of OSPF network of MPLS-VPN provider
多选题Which two statements are correct regarding the default protocol preference values? （）ARIP is preferred over OSPF external routesBDirect, local and static routes have the same preference valueCOSPF's preference value is lower than BGPDOSPF has a single preference value for both internal and external routes
多选题Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）Aset interfaces ge-0/3/0 unit 0 metric 10Bset protocols ospf reference-bandwidth 10gCset interfaces ge-0/3/0 unit bandwidth 10gDset protocols ospf area 0 interface ge-0/3/0 metric 10Eset protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
单选题Which statement is correct about an OSPF sham-link？（）AA sham-link is a logical link between PE routers that provides an OSPF adjacency between the PE routers and forwards customer traffic across it.BA sham-link is a logical link between PE routers that provides an OSPF adjacency between the PE routers and carries OSPF LSAs.CA sham-link is a logical link between PE routers that carries OSPF LSAs and forwards customer traffic across it.DA sham-link is a point-to-multipoint link that provides an OSPF adjacency between the PE routers and carries OSPF LSAs.EA sham-link is a point-to-multipoint link that provides an OSPF adjacency between the PE routers and forwards customer traffic across it.
多选题Process OSPF 1 is redistributing routes from process OSPF 2. Which of the following methods may be used to set the metrics of the redistributed routes?（）ALet the metrics default.BUse each redistributed route's OSPF metric using the redistribute command's metric transparent keywords.CSet the metric using the default - metric router subcommand.DRedistribution is not allowed between two OSPF p rocesses.
单选题By default if equal-cost paths exists for the same destination, which action will the router take?（）ADrop half the trafficBMake a copy of the traffic and send it to both testinationsCLoad-balance traffic between the available pathsDRandomly select one of the available paths to send traffic
单选题You have two EBGP peers connected via two parallel serial lines. What should you do to be able to load-balance between two EBGP speakers over the parallel serial lines in both directions？ （）Anothing，BGP automatically load-balances the traffic between different autonomous systems on all available linksBpeer between the eBGP speaker’s loopbacks， configuring eBGP multihop as required， and use an IGP to load-share between the two equal-cost paths between the loopback addressesCconfigure a loopback as update source for both EBGP peers and have on each AS an IGP to introduce two equal-cost paths to reach the EBGP peer loopback address；it is also necessary to use the next-hop-self commandDuse the ebgp-load-balance command on the neighbor statement on both sidesEconfigure a loopback as update source for both EBGP peers and have on each AS an IGP to introduce two equal-cost paths to reach the peer loopback address；it is also necessary to use the ebgp-multihop and next-hop-self commands
单选题Routers A and B have an OC12c and a GE link between them and are running OSPF over both of these links.Which item is correct， assuming the default JUNOS software OSPF metric calculation？（）AThere are two equal cost paths between A and BBThe GE link is the preferred path between A and BCThe OC12c link is the preferred path between A and BDManual metric assignment must be configured to determine the outcome.
多选题Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）Aset interfaces ge-0/3/0 unit 0 metric 10Bset protocols ospf reference-bandwidth 10gCset interfaces ge-0/3/0 unit 0 bandwidth 10gDset protocols ospf area 0 interface ge-0/3/0 metric 10Eset protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
多选题How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)（）。AIf RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.BIf RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.CIf EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.DIf EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.EIf EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.FIf EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.