单选题You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state. What must be true in an SVI configuration to bring the VLAN and line protocol up？（）AThe port must be physically connected to another Layer 3 device.BAt least one port in VLAN 20 must be active.CThe Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.DBecause this is a virtual interface， the operational status will always be in an up/up state.
单选题
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state. What must be true in an SVI configuration to bring the VLAN and line protocol up？（）
A
The port must be physically connected to another Layer 3 device.
B
At least one port in VLAN 20 must be active.
C
The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D
Because this is a virtual interface， the operational status will always be in an up/up state.
参考解析
解析：
暂无解析
相关考题：
As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）A. Automatic switchover from active to standby on primary supervisor failureB. Reset of the primary supervisor.C. Manual switchover from active to standby supervisorD. Manual switchover from standby to active supervisor
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method.When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A. Switch(config)# switchport trunk encapsulation islB. Switch(config)# switchport trunk encapsulation ietfC. Switch(config-if)# switchport trunk encapsulation islD. Switch(config-if)# switchport trunk encapsulation ietfE. Switch(config-if)# switchport trunk encapsulation dot1q
To which switch or switches should you provide redundant links in order to achieve high availability with reliable fast convergence in the enterprise campus?() A. to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 2 linkB. to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 3 linkC. to two core switches from redundant distribution switches connected with a Layer 2 linkD. to two core switches from redundant distribution switches connected with a Layer 3 linkE. to two core switches running Cisco NSF and SSO from two redundant distribution switches running Cisco NSF and SSO
When you enter the interface command auto qos voip cisco-phone on a port at the edge of a network,how does the Cisco Catalyst switch detect if a Cisco IP Phone is connected to the port?（）A、by snooping the CoS marking on the incoming framesB、by using RTP hello messages between the switch port and the Cisco IP PhoneC、by using CDPD、by using DHCP snoopingE、by snooping the incoming 802.1Q VLAN tag
To which switch or switches should you provide redundant links in order to achieve high availability with reliable fast convergence in the enterprise campus？（）A、 to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 2 linkB、 to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 3 linkC、 to two core switches from redundant distribution switches connected with Layer 2 linkD、 to two core switches from redundant distribution switches connected with Layer 3 linkE、 to two core switches running Cisco NSF and SSO from two redundant distribution switches running Cisco NSF and SSO
You examine the port statistics on a Cisco Catalyst switch and notice an excessive number offrames are being dropped. Which of the following are possible reasons for the drops？（）A、Unknown destination MAC addressB、Bad cablingC、MAC forwarding table is fullD、Port configured for half duplexE、Port configured for full duplexF、Network congestion
You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A、 Catalyst 2960 SeriesB、 Catalyst 3750 SeriesC、 Catalyst 4900 SeriesD、 Catalyst 6500 Series
Which two series of Cisco Catalyst switches， when placed in the distribution layer， effectively pass high amounts of network traffic between the core and access layers while aggregating access？ （）A、 Cisco Catalyst 2800B、 Cisco Catalyst 3550C、 Cisco Catalyst 3750D、 Cisco Catalyst 4500E、 Cisco Catalyst 6500
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state. What must be true in an SVI configuration to bring the VLAN and line protocol up？（）A、The port must be physically connected to another Layer 3 device.B、At least one port in VLAN 20 must be active.C、The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.D、Because this is a virtual interface， the operational status will always be in an "up/up" state.
If an enterprise customer required A switch for their branch office access layer, which family of switches would the customer likely choose from?（）A、Cisco SFS 3000/7000B、Cisco Catalyst 2000 and 3000C、Cisco Catalyst 4000 and 6000D、Cisco Nexus
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch， which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）A、 switchport access vlan vlan-idB、 switchportC、 switchport mode accessD、 no switchportE、 None of the other alternatives apply
You are bringing up a new Cisco Catalyst switch, and wish to connect it via a trunk to another switch from a different vendor, which uses the IEEE standard for the trunking method. When setting the encapsulation type on the trunk, what should you configure on the Cisco switch?（）A、Switch(config)# switchport trunk encapsulation islB、Switch(config)# switchport trunk encapsulation ietfC、Switch(config-if)# switchport trunk encapsulation islD、Switch(config-if)# switchport trunk encapsulation ietfE、Switch(config-if)# switchport trunk encapsulation dot1q
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A、The switch that will share its VLAN configuration must be in VTP server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be connected over VLAN trunks.E、The switches must be configured to use the same STP version.F、The switches must have VTP pruning activated.
A cisco 4404 wlan controller is being connected to a cisco 6500 catalyst series switch. How would you interconnect and configure lag for connectivity and ensure redundancy？（）A、all four ports from the cisco wlc terminated to the same catalyst gigabit module and channel group.B、ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 10 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 10.C、all four ports from the cisco wlc terminated to the same catalyst gigabit module using two channel groups.D、ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 20 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 40.
If an enterprise customer required a switch for their branch office access layer, which family of switches would the customer likely choose from?（）A、Cisco Catalyst 2000 and 3000B、Cisco NexusC、Cisco Catalyst 4000 and 6000D、Cisco SFS 3000/7000
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?（）A、The switch that will share the VLAN information must be in the VTP Server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be configured to use the same VTP version.E、The switches must be configured to use the same STP version.F、The switches must be configured to use the same type of ID tagging.G、The switches must be connected over VLAN trunks.
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.
多选题You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）AThe switch name must match the workgroup name of the local network.BThe switch must be configured with an IP address and default gateway.CThe remote workstations must have access to the management VLAN of the switch.DCDP must be enabled on the switch so that it can be located by other devices on the network.
多选题You examine the port statistics on a Cisco Catalyst switch and notice an excessive number offrames are being dropped. Which of the following are possible reasons for the drops？（）AUnknown destination MAC addressBBad cablingCMAC forwarding table is fullDPort configured for half duplexEPort configured for full duplexFNetwork congestion
单选题When configuring a routed port on a Cisco multilayer switch， which of these is a required configuration task that you must perform to enable that port to function as a routed port？ （）AEnable the switch to participate in routing updates from external devices with the router command in global configuration mode.BEnter the no switchport command to disable Layer 2 functionality at the interface level.CEach port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.DRouting is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
单选题You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch， which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）A switchport access vlan vlan-idB switchportC switchport mode accessD no switchportE None of the other alternatives apply
单选题You need to connect two Company core switches via an ISL trunk. Which statement is true regarding the configuration of ISL trunks？ （）A A Catalyst switch cannot have ISL and IEEE 802.1q trunks enabled.B All Catalyst switches support ISL trunking.C A Catalyst switch will report giants if one side is configured for ISL while the other side is not.D ISL trunking requires that native VLANs match.E None of the other alternatives apply
单选题As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）AAutomatic switchover from active to standby on primary supervisor failureBReset of the primary supervisor.CManual switchover from active to standby supervisorDManual switchover from standby to active supervisor
单选题To which switch or switches should you provide redundant links in order to achieve high availability with reliable fast convergence in the enterprise campus？（）A to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 2 linkB to a core switch running Cisco NSF and SSO from redundant distribution switches connected with a Layer 3 linkC to two core switches from redundant distribution switches connected with Layer 2 linkD to two core switches from redundant distribution switches connected with Layer 3 linkE to two core switches running Cisco NSF and SSO from two redundant distribution switches running Cisco NSF and SSO
单选题You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A Catalyst 2960 SeriesB Catalyst 3750 SeriesC Catalyst 4900 SeriesD Catalyst 6500 Series
单选题A Catalyst switch has just been installed and configured, and is not working as expected. You have decided to capture multiple show command outputs to study. Which one command could you use that includes the output of many other show commands, such as show version and show running-config?（）Ashow configurationBshow memoryCshow stacksDshow tech-support