As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）A. Automatic switchover from active to standby on primary supervisor failureB. Reset of the primary supervisor.C. Manual switchover from active to standby supervisorD. Manual switchover from standby to active supervisor
As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）
A. Automatic switchover from active to standby on primary supervisor failure
B. Reset of the primary supervisor.
C. Manual switchover from active to standby supervisor
D. Manual switchover from standby to active supervisor
相关考题：
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A. using DHCP snoopingB. snooping the incoming 802.1Q VLAN tagC. using CDPD. snooping the CoS marking on the incoming frames
What will happen if you issue the redundancy force－switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? () A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from active to standby supervisorD. automatic switchover from active to standby on primary supervisor failure
What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?() A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from active to standby supervisorD. automatic switchover from active to standby on primary supervisor failure
Which statement best describes Cisco supervisor engine redundancy using Stateful Switchover？（）A、Switchover ensures that Layer 2 through Layer 4 traffic is not interruptedB、Redundancy requires BGP， OSPF， EIGRP， or IS-ISC、Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switchesD、Switchover can be caused by clock synchronization failure between supervisors
Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy using NSF？（）A、 independent of SSOB、 NSF combined with SSO enables supervisor engine load balancingC、 supported by RIPv2， OSPF， IS-IS， and EIGRPD、 supports IPv4 and IPv6 multicastE、 prevents route flappingF、 dependent on FIB tables
Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancyusing NSF？（）A、independent of SSOB、NSF combined with SSO enables supervisor engine load balancingC、supported by RIPv2， OSPF， IS-IS， and EIGRPD、supports IPv4 and IPv6 multicastE、prevents route flappingF、dependent on FIB tables
You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A、 Catalyst 2960 SeriesB、 Catalyst 3750 SeriesC、 Catalyst 4900 SeriesD、 Catalyst 6500 Series
You have configured the Odyssey Access Client with a profile which has the "Disable Server Verification" setting cleared.What will be the result if the device certificate on the MAG Series device has expired and the user attempts to authenticate?（）A、The user will be instructed to call the network administrator.B、The user will fail authentication.C、The user will be prompted to install a new device certificate on the MAG Series device.D、The user will successfully authenticate and have full network access.
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）A、The switch that will share its VLAN configuration must be in VTP server mode.B、The switches must be in the same VTP domain.C、The switch that will share the VLAN information must be configured as the root bridge.D、The switches must be connected over VLAN trunks.E、The switches must be configured to use the same STP version.F、The switches must have VTP pruning activated.
What will happen if you issue the redundancy force-switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?（）A、reset of the primary supervisorB、manual switchover from standby to active supervisorC、manual switchover from active to standby supervisorD、automatic switchover from active to standby on primary supervisor failure
Company has a Catalyst 6500 and you need to configure redundancy between the supervisormodules. With route processor redundancy （RPR+）， the redundant supervisor engine is fullyinitialized and configured， which shortens the switchover time if the active supervisor engine fails.Which three statements are true about the RPR + operations when the redundant supervisorengine switched over the failed primary supervisor engine？（）A、Static IP routes are maintained across a switchover because they are configured from entries inthe configuration fileB、Information about dynamic routing states， maintained on the active supervisor engine， issynchronized to the redundant supervisor engine and is transferred during the switchoverC、Information about dynamic routing states， maintained on the active supervisor engine， is notsynchronized to the redundant supervisor engine and is lost on switchoverD、The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routedtraffic is interrupted until route tables reconvergeE、Static IP routes are cleared across a switchover and recreated from entries in the configurationfile on the redundant supervisor engineF、The Forwarding Information Base （FIB） tables are maintained during the switchover. As aresult， routed traffic continues without any interruption when the failover occurs
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A、using DHCP snoopingB、snooping the incoming 802.1Q VLAN tagC、using CDPD、snooping the CoS marking on the incoming frames
Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）A、CEF was not properly configured.B、OSPF was not properly configured for graceful restart.C、Stateful switchover was not correctly configured.D、NSF for OSPF is only supported in area 0.
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
多选题An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）AThe switch that will share its VLAN configuration must be in VTP server mode.BThe switches must be in the same VTP domain.CThe switch that will share the VLAN information must be configured as the root bridge.DThe switches must be connected over VLAN trunks.EThe switches must be configured to use the same STP version.FThe switches must have VTP pruning activated.
多选题You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）AThe switch name must match the workgroup name of the local network.BThe switch must be configured with an IP address and default gateway.CThe remote workstations must have access to the management VLAN of the switch.DCDP must be enabled on the switch so that it can be located by other devices on the network.
多选题Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy using NSF？（）Aindependent of SSOBNSF combined with SSO enables supervisor engine load balancingCsupported by RIPv2， OSPF， IS-IS， and EIGRPDsupports IPv4 and IPv6 multicastEprevents route flappingFdependent on FIB tables
单选题On the Catalyst 6500 Series switch, which command is used to establish a console connection to the Firewall Services Module?（）AsshBconnectCloginDsession
单选题A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch. Which of the following command will enable that?（）Ainterface vlan 100 ip access-group test inBinterface vlan 100 ip access-group testCvlan access-map test 100Dvlan filter test vlan-list 100
多选题pany has a Catalyst 6500 and you need to configure redundancy between the supervisor modules. With route processor redundancy （RPR+）， the redundant supervisor engine is fully initialized and configured， which shortens the switchover time if the active supervisor engine fails. Which three statements are true about the RPR + operations when the redundant supervisor engine switched over the failed primary supervisor engine？ （）AStatic IP routes are maintained across a switchover because they are configured from entries in the configuration file.BInformation about dynamic routing states， maintained on the active supervisor engine， is synchronized to the redundant supervisor engine and is transferred during the switchover.CInformation about dynamic routing states， maintained on the active supervisor engine， is not synchronized to the redundant supervisor engine and is lost on switchover.DThe Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routed traffic is interrupted until route tables reconverge.EStatic IP routes are cleared across a switchover and recreated from entries in the configuration file on the redundant supervisor engine.FThe Forwarding Information Base （FIB） tables are maintained during the switchover. As a result， routed traffic continues without any interruption when the failover occurs.
多选题Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancyusing NSF？（）Aindependent of SSOBNSF combined with SSO enables supervisor engine load balancingCsupported by RIPv2， OSPF， IS-IS， and EIGRPDsupports IPv4 and IPv6 multicastEprevents route flappingFdependent on FIB tables
单选题As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）AAutomatic switchover from active to standby on primary supervisor failureBReset of the primary supervisor.CManual switchover from active to standby supervisorDManual switchover from standby to active supervisor
单选题You have configured the Odyssey Access Client with a profile which has the "Disable Server Verification" setting cleared.What will be the result if the device certificate on the MAG Series device has expired and the user attempts to authenticate?（）AThe user will be instructed to call the network administrator.BThe user will fail authentication.CThe user will be prompted to install a new device certificate on the MAG Series device.DThe user will successfully authenticate and have full network access.
单选题You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？ （）AVerify that different native VLANs exist between two switches for security purposes.BVerify that the VLAN was added on all switches with the use of the show vlan command. CVerify that the switch is configured to allow for trunking on the switch ports.DVerify that each switch port has the correct IP address space assigned to it for the new VLAN.
单选题You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）A Catalyst 2960 SeriesB Catalyst 3750 SeriesC Catalyst 4900 SeriesD Catalyst 6500 Series
单选题What will happen if you issue the redundancy force-switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? （）Areset of the primary supervisorBmanual switchover from standby to active supervisorCmanual switchover from active to standby supervisorDautomatic switchover from active to standby on primary supervisor failure
单选题Which statement best describes Cisco supervisor engine redundancy using Stateful Switchover？（）ASwitchover ensures that Layer 2 through Layer 4 traffic is not interruptedBRedundancy requires BGP， OSPF， EIGRP， or IS-ISCRedundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switchesDSwitchover can be caused by clock synchronization failure between supervisors