单选题You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）AThe bypass-routing parameter is used to test the density on the T1 line.BThe bypass-routing parameter cannot be used on a T1 interface.CThe bypass-routing parameter allows you to ping a host through an interface that has no route through it.DThe bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.
单选题
You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
A
The bypass-routing parameter is used to test the density on the T1 line.
B
The bypass-routing parameter cannot be used on a T1 interface.
C
The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
D
The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.
参考解析
解析：
暂无解析
相关考题：
In the exhibit, what does the () symbol indicate?() A. There is a software issue with ge-1/0/1.0 interface.B. There is a hardware issue with ge-1/0/1.0 interface.C. The next hop of 172.25.213.11 is selected.D. The next hop of 172.25.213.11 is not resolvable.
When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?() A.ping atm vci 0.100 interface at-0/1/0 end-to-endB.ping atm vci 0.100 interface at-0/1/0 circuitC.ping atm vci 0.100 interface at-0/1/0 far-endD.ping atm vci 0.100 interface at-0/1/0 final-hop
Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）A. Serial 0 is up, line protocol is upB. Serial 0 is up, line protocol is downC. Serial 0 is down, line protocol is downD. Serial 0 is down, line protocol is upE. Serial 0 is administratively down, line protocol is downF. Serial 0 is administratively down, line protocol is up
You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?() A. Show interface lmiB. Show frame-relay lmiC. Show interface frame-relayD. Debug frame-relay interface.
Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。A、The IP address of sever 1.B、The MAC address of NIC in sever 1.C、The IP address of F0/0 interface of router R1.D、The MAC address of the Fa0/0 interface of router R1.E、The IP address of the s0/0/0 interface of router R2F、The MAC address of the s0/0/0 interface of router R2
While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）A、Serial 0 is up, line protocol is upB、Serial 0 is up, line protocol is downC、Serial 0 is down, line protocol is downD、Serial 0 is down, line protocol is upE、Serial 0 is administratively down, line protocol is downF、Serial 0 is administratively down, line protocol is up
You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall commandB、The count parameter allows the router to count the number of pings for logging purposesC、The count parameter allows the router to pause for 10000 seconds before sending out a pingD、The count parameter allows the router to send out 1000 pings and then stop
You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）A、The count parameter creates a counter that you can view with the show firewall command.B、The count parameter allows the router to count the number of pings for logging purposes.C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.D、The count parameter allows the router to send out 1000 pings and then stop.
You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the T1 line.B、The bypass-routing parameter cannot be used on a T1 interface.C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.
YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the TI line.B、The bypass-routing parameter cannot be used on a T1 interface.C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
You issue the command telnet interface ge-1/1/0 10.10.10.1 source 192.168.100.1 bypass-routing. Which statement is correct?（）A、The bypass-routing parameter is ignored when using private IP addressing.B、The telnet session will have the source IP address 10.10.10.1.C、The telnet session will connect to the neighboring device's interface ge-1/1/0.D、Return traffic for the telnet session might not arrive at interface ge-1/1/0.
How do you ping from configuration mode?（）A、[edit interfaces] user@router# run ping 1.1.1.1B、[edit interfaces] user@router# ping 1.1.1.1C、[edit interfaces] user@router# up ping 1.1.1.1D、[edit interfaces] user@router# exit ping 1.1.1.1
When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?（）A、ping atm vci 0.100 interface at-0/1/0 end-to-endB、ping atm vci 0.100 interface at-0/1/0 circuitC、ping atm vci 0.100 interface at-0/1/0 far-endD、ping atm vci 0.100 interface at-0/1/0 final-hop
You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the T1 lineB、The bypass-routing parameter cannot be used on a T1 interfaceC、The bypass-routing parameter allows you to ping a host through an interface that has no route through itD、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A、The Popcorn router is not forwarding RIP updates.B、The Popcorn router did not include network 192.168.12.0 in its routing configuration.C、The Ethernet1 interface of the Popcorn router is shutdown.D、The clockrate is not present in the configuration of one of the routers.E、The Serial interface of the Popcorn router is not operating.
You want to allow all hosts on interface ge-0/0/0.0 to be able to ping the device’s ge-0/0/0.0 IP address.Where do you configure this functionality？（）A、[edit interfaces]B、[edit security zones]C、[edit system services]D、[edit security interfaces]
单选题You want to allow all hosts on interface ge-0/0/0.0 to be able to ping the device’s ge-0/0/0.0 IP address.Where do you configure this functionality？（）A[edit interfaces]B[edit security zones]C[edit system services]D[edit security interfaces]
单选题You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）AThe bypass-routing parameter is used to test the density on the T1 lineBThe bypass-routing parameter cannot be used on a T1 interfaceCThe bypass-routing parameter allows you to ping a host through an interface that has no route through itDThe bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
单选题While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）ASerial 0 is up, line protocol is upBSerial 0 is up, line protocol is downCSerial 0 is down, line protocol is downDSerial 0 is down, line protocol is upESerial 0 is administratively down, line protocol is downFSerial 0 is administratively down, line protocol is up
单选题You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）AThe bypass-routing parameter is used to test the density on the T1 line.BThe bypass-routing parameter cannot be used on a T1 interface.CThe bypass-routing parameter allows you to ping a host through an interface that has no route through it.DThe bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.
单选题You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）AThe count parameter creates a counter that you can view with the show firewall command.BThe count parameter allows the router to count the number of pings for logging purposes.CThe count parameter allows the router to pause for 1000 seconds before sending out a ping.DThe count parameter allows the router to send out 1000 pings and then stop.
多选题The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）AThe Popcorn router is not forwarding RIP updates.BThe Popcorn router did not include network 192.168.12.0 in its routing configuration.CThe Ethernet1 interface of the Popcorn router is shutdown.DThe clockrate is not present in the configuration of one of the routers.EThe Serial interface of the Popcorn router is not operating.
单选题YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）AThe bypass-routing parameter is used to test the density on the TI line.BThe bypass-routing parameter cannot be used on a T1 interface.CThe bypass-routing parameter allows you to ping a host through an interface that has no route through it.DThe bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
单选题You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?（）AShow interface lmiBShow frame-relay lmiCShow interface frame-relayDDebug frame-relay interface.
单选题You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）AThe count parameter creates a counter that you can view with the show firewall commandBThe count parameter allows the router to count the number of pings for logging purposesCThe count parameter allows the router to pause for 10000 seconds before sending out a pingDThe count parameter allows the router to send out 1000 pings and then stop
单选题You issue the command telnet interface ge-1/1/0 10.10.10.1 source 192.168.100.1 bypass-routing. Which statement is correct?（）AThe bypass-routing parameter is ignored when using private IP addressing.BThe telnet session will have the source IP address 10.10.10.1.CThe telnet session will connect to the neighboring device's interface ge-1/1/0.DReturn traffic for the telnet session might not arrive at interface ge-1/1/0.
单选题How do you ping from configuration mode?（）A[edit interfaces] user@router# run ping 1.1.1.1B[edit interfaces] user@router# ping 1.1.1.1C[edit interfaces] user@router# up ping 1.1.1.1D[edit interfaces] user@router# exit ping 1.1.1.1