单选题During the inspection, the starting air valves should be closed （） the engine from turning.Ato increaseBto speed upCto preventDto reduce
单选题
During the inspection, the starting air valves should be closed （） the engine from turning.
A
to increase
B
to speed up
C
to prevent
D
to reduce
参考解析
解析：
暂无解析
相关考题：
If the engine does not start on air, it may be due toA.low compression of the fuel pumpsB.incorrect timing of fuel pumpsC.the starting air valves stuckD.air-locks in fuel oil pipeline
In an operating diesel engine, which of the following conditions is an indication of a leaking air starting valve?A.Noise coming from that air starting valveB.Continuous operation of the starting air compressorC.Zero air pressure in the air starting systemD.Overheated starting air pipe to the cylinder head
单选题When the order （） is received from the bridge, the main air stop valve in the starting air line should be shut.Astand-by engineBfull aheadCfinished with engineDfull away
单选题Which of the following may lead to the engine NOT to start on air?（）Astarting air pressure too highBcorrect timing of starting air valvesCthree of the six starting valves stuckDthe turning gear disengaged
单选题When an air started, four-stroke/cycle diesel engine is being cranked, the starting air is admitted to each cylinder during what would normally be the（）Aintake strokeBcompression strokeCpower strokeDexhaust stroke
单选题Which of the following methods is used to prevent throttling of compressed air through the diesel engine air starting valves?（）AHolding the valve open for a long periodBIncreasing the starting air pressure usedCOpening the stating air valve quicklyDReducing the starting air valve size
单选题If you are unable to stop a diesel engine by any other means，you should（）.Adischarge a CO2 extinguisher in the air inletBpull off the distributor capCsecure the jacket waterDsecure the starting air supply valve
单选题In the starting system, the automatic valve is controlled by（）, and the cylinder start valves are controlled by（）Apilot air；pilot airBhandle；solenoidChandle；pilot air coming through the distributorDsolenoid；pilot air coming through the distributor
单选题Before starting an air compressor, It should be （）.AturnedBoil level checkedCfilled with waterDA and B
单选题Air receivers installed in starting air systems are to be （）.Acylindrical in shape with service connections located at the top and bottomBopened and made available for inspection during biannual inspections providedCwith automatic drain traps for the removal of moistureDso installed as to make the drain connections effective under extreme conditions of trim
单选题Before starting an air compressor, It should be （）.AunloadedBprimedCfilled with waterDgreased
单选题During working of an air compressor, （） should be drained.Ainter coolerBcylinderCoutlet pipeDinlet pipe
单选题Air compressors are equipped with unloading systems for the purpose of（）.Aremoving all but the frictional load during startingBrelieving intercoolers of high temperature buildupsCproviding high starting torque in the drive motorDseating valve plates during compressor shutdown
单选题Inspection of a vessel’s propeller during dry-dock should include （）Anoting the condition of the fairwaterBinspection of the keywayClogging inspection results in the official deck logDall of above
单选题Which of the listed statements is correct concerning the starting of centrifugal pumps?（）AThey should always be started with the discharge valve closedBThey should always be started with the discharge valve openedCA priming pump is always required to flood the impeller suctionDThey should always be started with the sealing line valves closed
单选题If the engine does not start on air, it may be due to （）Alow compression of the fuel pumpsBincorrect timing of fuel pumpsCthe starting air valves stuckDair-locks in fuel oil pipeline
单选题Starting air valves are held firmly on their seats by（）Acam rollers on the camshaftBspring forceCair pressure on top of the valve differential pistonDair pressure on the bottom of the valve differential piston
单选题During （）, the starting air valves should be closed to prevent the engine from turning.AoverhaulBrunningCblowing downDAll of the above are correct
单选题An un-loader is installed on an air compressor to （）.Abypass the high pressure stage to the low pressure stage on 100% of the air compressors in serviceBprevent excessive inter-stage pressure buildupCcontrol compressor discharge pressureDremove all but the frictional load during starting
单选题After finished the engine, which of valves cannot be shut off by the duty engineer?（）Afuel valveBthe starting air valveCthe sea chestDthe main sea pump inlet valve
单选题In comparison to exhaust valves, intake valves of diesel engines may be fabricated from low alloy steels because （）.Athe beveled edges of the intake valves provide for serf-centering during seatingBintake valves utilize stellite-coated valve seat inserts which reduce wearCthe volume of air passing through intake valves is less than the volume of air passing through exhaust valvesDintake valves are less affected to the corrosive action of exhaust gases
单选题Prior to starting most medium-speed propulsion diesel engines, which of the procedures listed should be observed?（）AThe expansion tank should be topped offBThe thermostatic water regulating valves should be manually openedCThe fuel filters should be changedDThe engine should be turned over slowly with the indicator cocks open
单选题In an operating diesel engine, which of the following condition is an indication of a leaking air starting valve?（）Anoise coming from that air starting valveBcontinuous operation of the starting air compressorCzero air pressure in the air starting systemDoverheated starting air pipe to the cylinder head
单选题Explosions do occur （） caused by the ignition of oil or vapour gaining access from compressors or defective engine starting valves.Ain boiler drumsBin refrigerating plantsCin starting air pipesDin air coolers
单选题The starting air bottle should be pumped up to maximum pressure by the （） before start of the engine.Aair compressorBrefrigeration compressorCvacuum pumpDpurifier
单选题What is TRUE of pressure/vacuum valves? （）AThey are designed to provide for the flow of small volumes of tank atmospheres caused by thermal variations in a cargo tankBThey should operate in advance of the pressure/vacuum breakersCThey should be kept in good working order by regular inspection and cleaningDAll of the above