单选题Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1ANo routes are redistributed because a route cannot be both E1 and E2.BOnly OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.CInside the OSPF 2 domain, any formerly E2 routes will become E1 routes.DRoutes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
单选题
Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1
A
No routes are redistributed because a route cannot be both E1 and E2.
B
Only OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.
C
Inside the OSPF 2 domain, any formerly E2 routes will become E1 routes.
D
Routes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
参考解析
解析：
暂无解析
相关考题：
What type of OSPF router is responsible for redistributing routes into OSPF?() A. ABRB. ASBRC. internal routerD. backbone router
Router R1 sets a route tag for subnet 10.1.1.0／24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?() A. Kilobits/seconDB. Tens of microsecondsC. CostD. Hop countE. No unit is assigneD
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）A. show ip routeB. show ip eigrp topologyC. show ip ospf topologyD. show ip eigrp topology 10.1.1.0/24
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（）route - map fred deny 10match ip address oneroute - map fred deny 20match ip address tworoute - map fred permit 100A. The third route map clause will allow any routes not already filtered by the first two clausesB. R outes permitted by ACL two will be redistributedC. Routes denied by ACL one will be redistributedD. All routes will be filtereD
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?（）A. OSPF authentication errors between some of the routersB. Two routers have the same OSPF router IDC. Issues with mistuned OSPF timersD. OSPF LSA pacing issues between some of the routersE. OSPF neighbor adjacency problems between some of the routers
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）A、router bgp 1B、neighbor 2.2.2.2 remote- as 2C、neighbor 2.2.2.2 update - source loopback1D、neighbor 2.2.2.2 multihop 2
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds. What could be the cause of this problem?（）A、OSPF authentication errors between some of the routersB、Two routers have the same OSPF router IDC、Issues with mistuned OSPF timersD、OSPF LSA pacing issues between some of the routersE、OSPF neighbor adjacency problems between some of the routers
Router R1, an ASBR connected to the Internet and to backbone area 0, has been configured with a default - information originate command. Which of the following is true about the effects of this configuration command?（）A、R1 will always create and flood a default route into the OSPF domain.B、R1 will create and flood an LSA for prefix/length 0.0. 0.0/0 into the OSPF domain if R1's IP routing table has a route to 0.0.0.0/0.C、R1 will set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, regardless of whether R1 has a default route.D、R1 w ill set a flag on the LSA for the subnet between itself and one of the ISPs, noting this subnet as a default network, but only if R1 has a route to 0.0.0.0/0.
You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes. Which two things should you verify to troubleshoot this problem?（）A、The border router is using a proper seed metric for OSPFB、The border ro uter is using a proper seed metric for EIGRPC、The administrative distance is set for OSPF and EIGRPD、The missing EIGRP routes are present in the routing table of the border routerE、The subnet keyword on the border router in the redistribute EIG RP command
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0A、OSPF works on F0/0 and S0/0/0 without further configurationB、OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modEC、OSPF works with the addition of one command: an router - id command in OSPF router configuration modED、OSPFv3 needs at least two more configuration commands before it works on R1
Examine the following excerpt from the show ip eigrp topology 10.2.2.0/24 command on router R1.Which answer can be verified as definitely true based on this output?（） External data: Originating router is 10.1.1.1 AS number of route is 1 External protocol is OSPF, external metric is 64 Administrator tag is 0 (0x00000000)A、R1 is the router that redistributed the routeB、R1's metric to reach subnet 10.2.2.0/24 is 64C、The route was redistributed on a router that has a router ospf 1 command configuredD、R1 is redistributing a route to prefix 1 0.2.2.0/24 into OSPF
Which of the following answers is the least likely reason for an engineer to choose to use route redis tribution?（）A、To exchange routes between merged companiesB、To give separate control over routing to different parts of one companyC、To support multiple router vendorsD、To knit together an OSPF area if the area becomes discontiguous
You have just completed an OSPF implementation. While executing your verification plan, you determine that R1 is not able to establish full OSPF adjacency with R2. The show ip ospf neighbor comman d output on R1 shows that R2 is stuck in the INIT state. What could be the cause of this problem?（）A、DR and BDR election errors between R1 and R2.B、The R2 router has not received the OSPF hello packets from the R1 router.C、Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.D、Mismatched OSPF hello interval configuration between the R1 and R2E、Corrupted LSAs exchanges between the R1 and R2.
What is the requirement of Remote Triggered Black Hole （RTBH ） filtering？（）A、IBGP updates exchange between trigger router and black hole routerB、EBGP updates exchange between trigger router and black hole routerC、OSPF updates exchange between trigger router and black hole routerD、ISIS updates exchange between trigger router and black hole router
Router R1 refers to route - map fred when redistributing from EIGRP into OSPF. The entire route - map is listed next. Which of the following answers must be true based on the configuration as shown?（） route - map fred deny 10 match ip address one route - map fred deny 20 match ip address two route - map fred permit 100A、The third route map clause will allow any routes not already filtered by the first two clausesB、R outes permitted by ACL "two" will be redistributedC、Routes denied by ACL "one" will be redistributedD、All routes will be filtereD
Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）A、The show ip ospf neighbors command lists two neighbors off Fa0/0.B、The show ip ospf neighbors command lists four neighbors off Fa0/0.C、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.D、The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
A co-worker is developing an implementation plan for a design that uses OSPF 2 and RIPv2 routing domains, with two routers redistributing between the two domains.The co- worker asks your help in choosing how to prevent domain loops by setting administrative distance. Assuming all other related settings use defaults, which of the following would solve the domain loop problem?（）A、The distance ospf intra - area 80 inter - area 80 OSPF subcommandB、T he distance ospf external 80 OSPF subcommandC、The distance ospf intra - area 180 inter - area 180 OSPF subcommandD、The distance ospf external 180 OSPF subcommand
单选题A co-worker is developing an implementation plan for a design that uses OSPF 2 and RIPv2 routing domains, with two routers redistributing between the two domains.The co- worker asks your help in choosing how to prevent domain loops by setting administrative distance. Assuming all other related settings use defaults, which of the following would solve the domain loop problem?（）AThe distance ospf intra - area 80 inter - area 80 OSPF subcommandBT he distance ospf external 80 OSPF subcommandCThe distance ospf intra - area 180 inter - area 180 OSPF subcommandDThe distance ospf external 180 OSPF subcommand
单选题What type of OSPF router is responsible for redistributing routes into OSPF?（）AABRBASBRCinternal routerDbackbone router
单选题Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0AOSPF works on F0/0 and S0/0/0 without further configurationBOSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modECOSPF works with the addition of one command: an router - id command in OSPF router configuration modEDOSPFv3 needs at least two more configuration commands before it works on R1
单选题Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）Arouter bgp 1Bneighbor 2.2.2.2 remote- as 2Cneighbor 2.2.2.2 update - source loopback1Dneighbor 2.2.2.2 multihop 2
单选题Router R1 sets a route tag for subnet 10.1.1.0/24 when redistributing from OSPF into EIGRP.Which of the following unit is assigned to the route tag?（）AKilobits/seconDBTens of microsecondsCCostDHop countENo unit is assigneD
单选题Router R1 is redistributing between two OSPF processes. Given the configuration shown, which includes all commands in the route map named fred, which of the following answers is true regarding the redistribution into OSPF process 1?（） router ospf 1 redistribute ospf 2 external 2 route - map fred ! route - map fred permit 10 match ip address 1 set metric - type type - 1ANo routes are redistributed because a route cannot be both E1 and E2.BOnly OSPF E2 routes in the OSPF 2 domain will be considered for redistribution.CInside the OSPF 2 domain, any formerly E2 routes will become E1 routes.DRoutes permitted by ACL 1 will be redistributed, regardless of whether the routes are E1 or E2 routes.
多选题Rout er R1 directly connects to subnet 10.1.1.0/24 with its Fa0/0 interface. R1 can ping four other working OSPF routers in that subnet. R1 is neither the designated router (DR) nor backup DR (BDR). OSPF is working correctly on all five routers. Which of the following is true on R1?（）AThe show ip ospf neighbors command lists two neighbors off Fa0/0.BThe show ip ospf neighbors command lists four neighbors off Fa0/0.CThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.DThe show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
多选题Process OSPF 1 is redistributing routes from process OSPF 2. Which of the following methods may be used to set the metrics of the redistributed routes?（）ALet the metrics default.BUse each redistributed route's OSPF metric using the redistribute command's metric transparent keywords.CSet the metric using the default - metric router subcommand.DRedistribution is not allowed between two OSPF p rocesses.
多选题On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and 10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH. Which of the following co mmands on router R1 list subnet 10.1.1.0/24?（）Ashow ip routeBshow ip eigrp topologyCshow ip ospf topologyDshow ip eigrp topology 10.1.1.0/24