单选题Two routers configured to run BGP have been connected to a firewall，one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer，including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）AAttempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall.If telnet works，BGP will work，since telnet and BGP both use TCP to transport dataBPing from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall.If you can ping between them，BGP should work，since BGP uses IP to transport packetsCThere is no way to make BGP work across a firewall without special configuration，so there is no simple test that will show you if BGP will work or not，other than trying to start the peering sessionDThere is no way to make BGP work across a firewall
单选题
Two routers configured to run BGP have been connected to a firewall，one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer，including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）
A
Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall.If telnet works，BGP will work，since telnet and BGP both use TCP to transport data
B
Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall.If you can ping between them，BGP should work，since BGP uses IP to transport packets
C
There is no way to make BGP work across a firewall without special configuration，so there is no simple test that will show you if BGP will work or not，other than trying to start the peering session
D
There is no way to make BGP work across a firewall
参考解析
解析：
暂无解析
相关考题：
Routers A and B are connected with a point-to-point OC-3 interface. Each router‘s OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in the same area.How many IS-IS adjacencies exist between the two routers?（）A.0B.1C.2D.3
Routers A and B are connected with a point-to-point OC-3 interface. Each routers OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in different areas. How many IS-IS adjacencies exist between the two routers?（）A.0B.1C.2D.3
Refer to the exhibit. On the basis of the output, what two conclusions can be reached?() A. The default administrative distance has been changed.B. IS - IS is not enabled.C. Three physical interfaces are taking part in integrated IS - IS.D. IS - IS is not redistributing any oth er routing protocols.E. There are two neighboring routers sending IS - IS routing information.F. Address summarization is configured.
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A、As numbers must be changed to match on all the routers.B、Loopback interface must be configured so a DR is elected.C、The no auto-summary command is needed on Router A and Router C.D、Router B needs to have two network statements, one for each connected network.
Two BGP peers connected through a routed firewall are unable to establish a peering relationship. What could be the most likely cause？（）A、BGP peers must be Layer 2-adjacent.B、EBGP multihop is not configured.C、The firewall is not configured to allow IP protocol 89.D、The firewall is not configured to allow UDP 179.
In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）A、Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.B、A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.C、A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.D、A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
When BGP is used as the PE-CE routing protocol, which of these statements is correct?（）A、On the CE router, PE neighbors must be configured in the VRF context on the CE routerB、On PE routers, the CE IBGP neighbors are configured in the global BGP configurationC、On PE routers, the CE EBGP neighbors are configured in the VRF contextD、A separate BGP process must be used on the PE routers for CE routers so that they do not use the same BGP routing process as that used for the PE router's other provider neighbors
Routers A and B are connected with a point-to-point OC-3 interface. Each routers OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in different areas. How many IS-IS adjacencies exist between the two routers?（）A、0B、1C、2D、3
Which condition must be met to allow a PE router to forward VPN traffic across a LSP in a Layer 3 VPN environment？（）A、The BGP next hop must be in inet.1.B、The BGP next hop must be in inet.3.C、Must have a bidirectional LSP configured.D、Must have a static route to allow an RP for connected interfaces.
Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）A、Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.B、Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.C、There is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.D、There is no way to make BGP work across a firewall.
Two BGP peers connected through a routed firewall are unable to establish a peering relationship. What could be the most likely cause？ （）A、 BGP peers must be Layer 2-adjacentB、 EBGP multihop is not configuredC、 The firewall is not configured to allow IP protocol 89D、 The firewall is not configured to allow UDP 179.
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）A、A hub router prevents routes from being advertised to the remote router.B、Only remote routers are configured as stubs.C、Stub routers are not queried for routes.D、Spoke routers connected to hub routers answer the route queries for the stub router.E、A stub router should have only EIGRP hub routers as neighbors.F、EIGRP stub routing should be used on hub routers only.
In an environment in which multiple VLANs have been defined on Catalyst Express 500 switches， which two statements are correct for ports that have been configured with the Smartport role of "IP Phone + Desktop"？（）A、The names of the VLANs used by the SmartPorts are case insensitiveB、The ports may belong to a configurable data VLANC、The names of the VLANs used by the Smartports are not relevantD、The ports may belong to many VLANs， depending on how many PCs are connected to each port.E、The names of the VLANs used by the Smartports are case sensitive
Which of the following is required to ensure the completion of all tests within the automated procedure of thecluster test tool？（）A、Application monitoring has been configuredB、Only disk heartbeat networks have been usedC、Cluster nodes are attached to two IP networksD、Resource Group dependencies have been configured
单选题In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）ATwo switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.BA router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.CA router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.DA router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.
多选题When HSRP is configured on a network, which two of these items are provided, which are shared between the routers that run HSRP ?（） (choose two)AShared single interfaceBIP AddressCTCP-based hello packetsDMAC address
单选题Routers A and B are connected with a point-to-point OC-3 interface. Each routers OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in different areas. How many IS-IS adjacencies exist between the two routers?（）A0B1C2D3
单选题Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall？（）AAttempt to TELNET from the router connected to the inside of the firewall to the router connected to theoutside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transportdata.BPing from the router connected to the inside interface of the firewall to the router connected to theoutside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP totransport packets.CThere is no way to make BGP work across a firewall without special configuration， so there is no simpletest that will show you if BGP will work or not， other than trying to start the peering session.DThere is no way to make BGP work across a firewall.
单选题Two BGP peers connected through a routed firewall are unable to establish a peering relationship. What could be the most likely cause？（）ABGP peers must be Layer 2-adjacent.BEBGP multihop is not configured.CThe firewall is not configured to allow IP protocol 89.DThe firewall is not configured to allow UDP 179.
单选题Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）AAs numbers must be changed to match on all the routers.BLoopback interface must be configured so a DR is elected.CThe no auto-summary command is needed on Router A and Router C.DRouter B needs to have two network statements, one for each connected network.
单选题When BGP is used as the PE-CE routing protocol, which of these statements is correct?（）AOn the CE router, PE neighbors must be configured in the VRF context on the CE routerBOn PE routers, the CE IBGP neighbors are configured in the global BGP configurationCOn PE routers, the CE EBGP neighbors are configured in the VRF contextDA separate BGP process must be used on the PE routers for CE routers so that they do not use the same BGP routing process as that used for the PE router's other provider neighbors
单选题Which condition must be met to allow a PE router to forward VPN traffic across a LSP in a Layer 3 VPN environment?（）AThe BGP next hop must be in inet.1.BThe BGP next hop must be in inet.3.CMust have a bidirectional LSP configured.DMust have a static route to allow an ARP for connected interfaces.
单选题Routers A and B are connected with a point-to-point OC-3 interface. Each router’s OC-3 interface is configured for both Level 1 and Level 2. The routers are configured in different areas.How many IS-IS adjacencies exist between the two routers？（）A0B1C2D3
多选题In an environment in which multiple VLANs have been defined on Catalyst Express 500 switches， which two statements are correct for ports that have been configured with the Smartport role of "IP Phone + Desktop"？（）AThe names of the VLANs used by the SmartPorts are case insensitiveBThe ports may belong to a configurable data VLANCThe names of the VLANs used by the Smartports are not relevantDThe ports may belong to many VLANs， depending on how many PCs are connected to each port.EThe names of the VLANs used by the Smartports are case sensitive
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router
单选题Two BGP peers connected through a routed firewall are unable to establish a peering relationship. What could be the most likely cause？ （）A BGP peers must be Layer 2-adjacentB EBGP multihop is not configuredC The firewall is not configured to allow IP protocol 89D The firewall is not configured to allow UDP 179.
单选题Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）AAttempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.BPing from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.CThere is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.DThere is no way to make BGP work across a firewall.