多选题Router 1 is configured for BGP as dual-homed on the Cisco network. Which three BGP attributes are carried in every BGP update on this router （both IBGP and EBGP）？（）AoriginBrouter-IDCAS-pathDlocal-preferenceEnext-hop
多选题
Router 1 is configured for BGP as dual-homed on the Cisco network. Which three BGP attributes are carried in every BGP update on this router （both IBGP and EBGP）？（）
A
origin
B
router-ID
C
AS-path
D
local-preference
E
next-hop
参考解析
解析：
暂无解析
相关考题：
A BGP router is configured with bgp dampening 8 300 1500 20 route－map 1 .What does the value of 20 represent?() A. reuseB. suppressC. half-lifeD. max-suppress-time
BGP route dampening is configured on a BGP router.Whose routing behavior is affected by this configuration?() A. upstream EBGP neighborsB. downstream EBGP neighborsC. upstream IBGP neighbors learned by IBGP peersD. downstream IBGP neighbors learned by IBGP peers
A BGP connection is being established.What happens if the local router and the peer router do NOT have the same hold－time value configured?() A. The BGP session does not establish.B. The hold time is assumed to be infinite.C. The larger of the two hold-time values is used.D. The smaller of the two hold-time values is used.
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）A. Stateful Switchover for Cisco Nonstop Forwarding only works with BGP.B. Stateful Switchover for Cisco Nonstop Forwarding must be configured on all adjacent routers.C. Cisco Nonstop Forwarding with Stateful Switchover helper mode is not supported on the adjacent router.D. Cisco Nonstop Forwarding with Stateful Switchover helper mode for OSPF has been promiscuousstandardized and is supported on the adjacent router.
When the BGP path selection process is being performed on a Cisco router, which BGP attribute is used first when determining the best path?() A. local preferenceB. MEDC. weightD. or iginE. next - hopF. AS - path
Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? () A.The Router1 WAN port is configured as a trunking port.B.The Router1 port connected to Switch1 is configured using subinterfaces.C.The Router1 port connected to Switch1 is configured as 10 Mbps.D.The Switch1 port connected to Router1 is configured as a trunking port.E.The Switch1 port connected to Host B is configured as an access port.F.The Switch1 port connected to Hub1 is configured as full duplex.
When the BGP path selection process is being performed on a Cisco router, which BGP attribute is used first when determining the best path?（）A、local preferenceB、MEDC、weightD、or iginE、next - hopF、AS - path
When BGP is used as the PE-CE routing protocol, which of these statements is correct?（）A、On the CE router, PE neighbors must be configured in the VRF context on the CE routerB、On PE routers, the CE IBGP neighbors are configured in the global BGP configurationC、On PE routers, the CE EBGP neighbors are configured in the VRF contextD、A separate BGP process must be used on the PE routers for CE routers so that they do not use the same BGP routing process as that used for the PE router's other provider neighbors
SR7750调测BGP邻居状态变化的命令是（）A、debug router bgp openB、debug router bgp eventsC、debug router bgp updateD、debug router bgp packets
Which condition must be met to allow a PE router to forward VPN traffic across a LSP in a Layer 3 VPN environment？（）A、The BGP next hop must be in inet.1.B、The BGP next hop must be in inet.3.C、Must have a bidirectional LSP configured.D、Must have a static route to allow an RP for connected interfaces.
Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）A、Attempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.B、Ping from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.C、There is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.D、There is no way to make BGP work across a firewall.
Router 1 is configured for BGP as dual-homed on the Cisco network. Which three BGP attributes are carried in every BGP update on this router （both IBGP and EBGP）？（）A、originB、router-IDC、AS-pathD、local-preferenceE、next-hop
What is the most likely reason for the dispartly between the actual network numbers at the branches and the routes in the routing table on Gateway-Router?（）A、Branch-Router2 is configured to send both RIPv1 and RIPv2 updates.B、Gateway-Router is configured to only receive RIPv2 updates.C、Gateway-router is configured to receive only RIPv1 updates.D、Branch-Router1 is configured to only send RIPv1 updates
The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?（） BGP router identifier 11.11.11.11, local AS number 11 ... Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle (Admin) 2.2.2.2 4 3 173 183 41 0 0 00:58:47A、router bgp 11B、neighbor 1.1.1.1 remote- as 11C、neighbor 2.2.2.2 prefix - limit 1D、neighbor 1.1.1.1 shutdown
Which of the following events would not explain excessive CPU utilization？（）A、A large number of BGP sessionsB、A large BGP tableC、A router is configured with the following command： ip route 0.0.0.0 0.0.0.0 fa 0/1D、All interface buffers are continually in useE、A flapping interfaceF、The router sends a large number of ARP requests
Router R-1 is configured for BGP routing as shown below： router bgp 65300network 27.0.0.0neighbor 192.23.1.1 remote-as 65300 From the perspective of router R-1， what kind of router is the router with IP address 192.23.1.1？（）A、A peer router running IBGPB、A peer router running EBGPC、A community member running IBGPD、A peer group member running IBGPE、A peer group member running EBGP
When a Cisco router is configured for SSH, it acts as an （）?A、SSH clientB、SSH proxyC、SSH serverD、SSH and SSL server
What s the default stratum clock on a Cisco router，when you see the key word "master" configured on the NTP line？（）A、1B、2C、4D、6E、8
A BGP router is configured with bgp dampening 8 300 1500 20 route-map 1 .What does the value of 20 represent?（）A、reuseB、suppressC、half-lifeD、max-suppress-time
单选题Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall？（）AAttempt to TELNET from the router connected to the inside of the firewall to the router connected to theoutside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transportdata.BPing from the router connected to the inside interface of the firewall to the router connected to theoutside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP totransport packets.CThere is no way to make BGP work across a firewall without special configuration， so there is no simpletest that will show you if BGP will work or not， other than trying to start the peering session.DThere is no way to make BGP work across a firewall.
单选题When BGP is used as the PE-CE routing protocol, which of these statements is correct?（）AOn the CE router, PE neighbors must be configured in the VRF context on the CE routerBOn PE routers, the CE IBGP neighbors are configured in the global BGP configurationCOn PE routers, the CE EBGP neighbors are configured in the VRF contextDA separate BGP process must be used on the PE routers for CE routers so that they do not use the same BGP routing process as that used for the PE router's other provider neighbors
多选题The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（） R1# show ip bgp 19 0.1.0.0/16 BGP routing table entry for 190.1.0.0/16, version 121 Paths: (1 available, best #1, table Default - IP - Routing - Table) Advertised to update - groups: 1 1 2 3 4 1.1.1.1 from 2.2.2.2 (3.3.3.3) Origin IGP, metric 0, localpref 100, valid, internal, bestAR1 has a neighbor 1.1.1.1 command configured.BR1 has a neighbor 2.2.2.2 command configured.CThe show ip bgp command lists a line for 190.1.0.0/16 with both an and an i on the left.DR1 is in ASN 1.
单选题Which of the following events would not explain excessive CPU utilization？（）AA large number of BGP sessionsBA large BGP tableCA router is configured with the following command： ip route 0.0.0.0 0.0.0.0 fa 0/1DAll interface buffers are continually in useEA flapping interfaceFThe router sends a large number of ARP requests
单选题Router R-1 is configured for BGP routing as shown below： router bgp 65300network 27.0.0.0neighbor 192.23.1.1 remote-as 65300 From the perspective of router R-1， what kind of router is the router with IP address 192.23.1.1？（）AA peer router running IBGPBA peer router running EBGPCA community member running IBGPDA peer group member running IBGPEA peer group member running EBGP
单选题A BGP router is configured with bgp dampening 8 300 1500 20 route-map 1 .What does the value of 20 represent?（）AreuseBsuppressChalf-lifeDmax-suppress-time
多选题Router 1 is configured for BGP as dual-homed on the Cisco network. Which three BGP attributes are carried in every BGP update on this router （both IBGP and EBGP）？（）AoriginBrouter-IDCAS-pathDlocal-preferenceEnext-hop
单选题BGP route dampening is configured on a BGP router. Whose routing behavior is affected by this configuration?（）Aupstream EBGP neighborsBdownstream EBGP neighborsCupstream IBGP neighbors learned by IBGP peersDdownstream IBGP neighbors learned by IBGP peers
单选题Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correct BGP session endpoint addresses and the correct BGP session hop-count limit （EBGP multihop）. What is a good first test to see if BGP will work across the firewall？（）AAttempt to TELNET from the router connected to the inside of the firewall to the router connected to the outside of the firewall. If telnet works， BGP will work， since telnet and BGP both use TCP to transport data.BPing from the router connected to the inside interface of the firewall to the router connected to the outside interface of the firewall. If you can ping between them， BGP should work， since BGP uses IP to transport packets.CThere is no way to make BGP work across a firewall without special configuration， so there is no simple test that will show you if BGP will work or not， other than trying to start the peering session.DThere is no way to make BGP work across a firewall.