单选题Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）ATrunkBIsolatedCPrimaryDCommunityEPromiscuousFNone of the other alternatives apply
单选题
Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）
A
Trunk
B
Isolated
C
Primary
D
Community
E
Promiscuous
F
None of the other alternatives apply
参考解析
解析：
暂无解析
相关考题：
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero
Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?（）A.VLANs have not been created yetB.An IP address must be configured for the portC.The port is currently configured for access modeD.The correct encapsulation type has not been configuredE.The no shutdown command has not been entered for the port
A lightweight access point has been connected to a Catalyst 3550 24-PWR switch， and on power-up the access point fails. What is the problem with the switch？（）A、The power supply has inadequate wattage.B、Power is incorrectly configured on the port.C、It does not support 802.3af Poe.D、Power is not enabled on the port.
Switch R1 has been configured with Private VLANs. With that type of PVLAN port should the default gateway be configured？（）A、 TrunkB、 IsolatedC、 PrimaryD、 CommunityE、 PromiscuousF、 None of the other alternatives apply
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。A、a switch with a trunk link that is configured between the switchesB、a router with an IP address on the physical interface that is connected to the switchC、a switch with an access link that is configured between the switchesD、a router with subinterfaces configured on the physical interface that is connected to the switch
A switch that is to be added to the production network has been preconfigured （trunks， VLANs， VTP， and STP） and was tested in your lab. After installing the switch into the network， the entire network went down. What might explain what happened？ （）A、The new switch happened to be running Cisco Catalyst operating system， while the other network switches were running Cisco IOS Software.B、The configuration revision of the new switch was higher than the configuration revision of the production VTP domain.C、The link costs on the new switch are set to a high value， causing all ports on the new switch to go into a forwarding mode and none into blocking mode， thereby causing a spanning-tree loop.D、The ports connecting to the two switches have been configured incorrectly. One side has the command switchport mode access and the other switchport mode trunk.
A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network. Which three issues on Switch2 could be the cause？（）A、Switch2 is configured for only VLAN1B、Switch2 is a VTP server in a different domainC、Switch2 is a VTP server in the Company domainD、Switch2 is not a VTP domain.E、Switch2 has a lower VTP configuration revision number than the current VTP revisionF、Switch2 has a higher VTP configuration revision number than the current VTP revision
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
You work as a network Technician. A new workstation has consistently been unable to obtain anIP address from the DHCP server when the workstation boots. Older workstations function normally， and the new workstation obtains an address when manually forced to renew its address. What should be configured on the switch to allow the workstation to obtain an IP address at boot？（）A、UplinkFast on the switch port connected to the serverB、BackboneFast on the switch port connected to the serverC、PortFast on the switch port connected to the workstationD、trunking on the switch
The DAI feature has been implemented in the Company switched LAN. Which three statements are true about the dynamic ARP inspection （DAI） feature？ （）A、 DAI can be performed on ingress ports only.B、 DAI can be performed on both ingress and egress ports.C、 DAI is supported on access ports， trunk ports， EtherChannel ports， and private VLAN ports. D、 DAI should be enabled on the root switch for particular VLANs only in order to secure the ARP caches of hosts in the domain.E、 DAI should be configured on all access switch ports as untrusted and on all switch ports connected to other switches as trusted.F、 DAI is supported on access and trunk ports only.
A cisco aironet 1020 controller-based access point has been connected to a catalyst 3550-24 pwr switch. however， when it is powered up， the access point fails. What has caused this problem？（）A、access point does not support 802.11hB、incorrect switch power supplyC、switch port is not enabledD、switch does not support 802.3afE、access point has not been initialized with the primary controller
Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）A、TrunkB、IsolatedC、PrimaryD、CommunityE、PromiscuousF、None of the other alternatives apply
Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）A、R1 has been configured with an ip default- network 2.0.0.0 command.B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.D、Another router has been configured with an ip default - network 2.0.0.0 command.E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）A、a router with subinterfaces configured on the physical interface that is connected to the switchB、a router with an IP address on the physical interface connected to the switchC、a switch with an access link that is configured between the switchesD、a switch with a trunk link that is configured between the switches
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）A、The wrong cable type has been used.B、. IDS has shut down the computer's switch port.C、The port on the switch is configured incorrectlyD、Spanning tree protocol was implemented.
A user is browsing to a newly created internal site called www.comptia.org. After putting incredentials the page comes up blank. Which of the following is MOST likely the cause?（）A、The user must add the new site to the local log file.B、A proxy exception has not been configured.C、SMTP has not been configured.D、The loopback address has not been configured.
单选题Switch R1 has been configured with Private VLANs. With that type of PVLAN port should the default gateway be configured？（）A TrunkB IsolatedC PrimaryD CommunityE PromiscuousF None of the other alternatives apply
单选题Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。Aa switch with a trunk link that is configured between the switchesBa router with an IP address on the physical interface that is connected to the switchCa switch with an access link that is configured between the switchesDa router with subinterfaces configured on the physical interface that is connected to the switch
单选题A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）AoneBthreeCtwoDzero
单选题A user is browsing to a newly created internal site called www.comptia.org. After putting incredentials the page comes up blank. Which of the following is MOST likely the cause?（）AThe user must add the new site to the local log file.BA proxy exception has not been configured.CSMTP has not been configured.DThe loopback address has not been configured.
多选题The DAI feature has been implemented in the Company switched LAN. Which three statements are true about the dynamic ARP inspection （DAI） feature？ （）ADAI can be performed on ingress ports only.BDAI can be performed on both ingress and egress ports.CDAI is supported on access ports， trunk ports， EtherChannel ports， and private VLAN ports.DDAI should be enabled on the root switch for particular VLANs only in order to secure the ARP caches of hosts in the domain.EDAI should be configured on all access switch ports as untrusted and on all switch ports connected to other switches as trusted.FDAI is supported on access and trunk ports only.
多选题A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network. Which three issues on Switch2 could be the cause？（）ASwitch2 is configured for only VLAN1BSwitch2 is a VTP server in a different domainCSwitch2 is a VTP server in the Company domainDSwitch2 is not a VTP domain.ESwitch2 has a lower VTP configuration revision number than the current VTP revisionFSwitch2 has a higher VTP configuration revision number than the current VTP revision
单选题A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）AThe wrong cable type has been used.B. IDS has shut down the computer's switch port.CThe port on the switch is configured incorrectlyDSpanning tree protocol was implemented.
单选题Switch SW1 has been configured with Private VLANs. With that type of PVLAN port should thedefault gateway be configured？（）ATrunkBIsolatedCPrimaryDCommunityEPromiscuousFNone of the other alternatives apply
单选题On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）Aa router with subinterfaces configured on the physical interface that is connected to the switchBa router with an IP address on the physical interface connected to the switchCa switch with an access link that is configured between the switchesDa switch with a trunk link that is configured between the switches
单选题You have just created a new VLAN on your network for inter-VLAN routing. What is one step that you should include in your VLAN-based implementation and verification plan？（）AVerify that different native VLANs exist between two switches for security purposes.BVerify that the switch is configured to allow for trunking on the switch ports.CVerify that each switch port has the proper IP address space assigned to it for the new VLAN. DVerify that the VLAN virtual interface has been correctly created and enabled.
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router