单选题Which of the following should be performed after a maintenance kit has been applied and fullfunctionality tested?（）ARoller regenerator appliedBPage count resetCNew network settings appliedDPrinter drum replacement
单选题
Which of the following should be performed after a maintenance kit has been applied and fullfunctionality tested?（）
A
Roller regenerator applied
B
Page count reset
C
New network settings applied
D
Printer drum replacement
参考解析
解析：
暂无解析
相关考题：
At which of the following times should the administrator refer to the HCL?() A. Prior to purchasing hardwareB. Before installationC. When installing driversD. After installation
A parallel printer has just been connected. There are not selections in the SMIT menu to configure the printer. Which of the following procedures should be performed to complete the configuration?() A.chdevB.rebootC.lpstat -QD.smit install
Which statement is TRUE concerning insulating flanges ________．A.They should be inspected and tested periodically to ensure that the insulation is clean and in good conditionB.Switching off a cathodic protection system may be substituted for using an insulating flangeC.The measured resistance value after installation should be less than 1，000 ohmsD.After the insulating flange is installed，hot work may be performed on deck
A technician has resolved a paper jam. After the jam is cleared, the display continues to indicate that the printer is jammed. Which of the following should be performed NEXT?（）A、Power cycle the printerB、Print a test pageC、Remove all the paper trays and restart the printerD、Remove and replace the roller
A technician（技术） has a current baseline（基准线） and is told to install additional（添加） memory and a faster NIC card. At which point in time should the next baseline be run？（）A、 After the memory is installedB、 Before the upgrade is performedC、 After the NIC is installedD、 After the upgrades are performed
Which of the following troubleshooting steps should be performed NEXT after a core router hasbeen reported down?（）A、Implement a solution.B、Establish the outage cause.C、Identify all affected areas.D、Test a solution.
Which of the following should be done before and after a service or repair is performed on a server？（）A、 DefragB、 IPCONFIG /releaseC、 Firmware updateD、 Baseline
Which of the following is an environmental server maintenance task that should be performed every three months?（）A、Replace the rubber mats in the server roomB、Clean the servers to limit dust buildupC、Wash the outside of the serversD、Replace the server fans
Which of the following documents should always be kept up-to-date after any major changes aremade to a network backbone?（）A、Network diagramB、Performance baselineC、Network security procedureD、Company policy
At which of the following times should the administrator refer to the HCL?（）A、Prior to purchasing hardwareB、Before installationC、When installing driversD、After installation
A patch has been applied to the operating system. After rebooting, the system is hung. Which of the following commands should have been performed to prevent the system from hanging?（）A、 lppchk, bosboot B、 lslpp -l, oslevel C、 installp -C, lppchk D、 bosboot, synclvodm
Which of the following procedures should be performed to minimize possible problems for a customer when updating software?（）A、Apply the updates without committing.B、Commit the new updates to be certain there is no change after the next reboot.C、Update one fileset at a time and test to ensure that it works before updating the next fileset.D、No action is necessary since the software can always be uninstalled and re-installed.
After the LED display is flashing 888 and the system is rebooted, which of the following commands should be used to gather dump information?（）A、snap B、errpt C、kdb D、trace
A parallel printer has just been connected. There are not selections in the SMIT menu to configure the printer. Which of the following procedures should be performed to complete the configuration?（）A、chdevB、rebootC、lpstat -QD、smit install
A customer indicates that a system is experiencing printing problems. After checking the system, and successfully printing, no problem has been found. Which of the following procedures should be performed next to further clarify the problem?（）A、 Reboot the system.B、 Check the file system sizes.C、 Have the customer repeat the task to recreate the problem.D、 Inform the customer that no problems were found， and to call back if the problem reoccurs.
A system administrator needs to replace a mirrored disk. After performing the proper removal process and replacing the disk, which of the following set of commands should be performed to bring the disk back into production?（）A、 reboot, mklvcopy, syncvg B、 cfgmgr -vl ssar, chvg -va, syncvg C、 cfgmgr, extendvg, syncvg D、 extendvg, mklvcopy, syncvg
In which phase should a TDA be performed of the following？（）A、Server deploymentB、Installation and server configurationC、Problem determination / resolutionD、Needs analysis and design
In order to change the system runlevel and execute /etc/inittab entries based on the new runlevel, which of the following commands should be performed?（）A、telinitB、runinitC、sysinitD、startinit
单选题After a technician installs a video card, which of the following should the technician configure NEXT?（）AResolutionBColorsCDots per inchDRefresh rate
单选题At which of the following times should the administrator refer to the HCL？（）A Prior to purchasing hardwareB Before installationC When installing driversD After installation
单选题A system administrator needs to replace a mirrored disk. After performing the proper removal process and replacing the disk, which of the following set of commands should be performed to bring the disk back into production?（）A reboot, mklvcopy, syncvg B cfgmgr -vl ssar, chvg -va, syncvg C cfgmgr, extendvg, syncvg D extendvg, mklvcopy, syncvg
单选题Which of the following is an environmental server maintenance task that should be performed every three months？（）A Replace the rubber mats in the server roomB Clean the servers to limit dust buildupC Wash the outside of the serversD Replace the server fans
单选题Which of the following procedures should be performed to minimize possible problems for a customer when updating software?（）AApply the updates without committing.BCommit the new updates to be certain there is no change after the next reboot.CUpdate one fileset at a time and test to ensure that it works before updating the next fileset.DNo action is necessary since the software can always be uninstalled and re-installed.
单选题A customer indicates that a system is experiencing printing problems. After checking the system, and successfully printing, no problem has been found. Which of the following procedures should be performed next to further clarify the problem?（）A Reboot the system.B Check the file system sizes.C Have the customer repeat the task to recreate the problem.D Inform the customer that no problems were found， and to call back if the problem reoccurs.
单选题A technician（技术） has a current baseline（基准线） and is told to install additional（添加） memory and a faster NIC card. At which point in time should the next baseline be run？（）A After the memory is installedB Before the upgrade is performedC After the NIC is installedD After the upgrades are performed
单选题Which of the following should be done before and after a service or repair is performed on a server？（）A DefragB IPCONFIG /releaseC Firmware updateD Baseline
单选题A patch has been applied to the operating system. After rebooting, the system is hung. Which of the following commands should have been performed to prevent the system from hanging?（）A lppchk, bosboot B lslpp -l, oslevel C installp -C, lppchk D bosboot, synclvodm