单选题On a network switch, which of the following is the default native VLAN?（）A0B1C1024D4096
单选题
On a network switch, which of the following is the default native VLAN?（）
A
0
B
1
C
1024
D
4096
参考解析
解析：
暂无解析
相关考题：
The Ezonexam network administrator has just issued the "switchport trunk native vlan 998" command on switch VE2. What is the function of this command?A．It designates VLAN 998 as the default for all unknown tagged trafficB．It designates VLAN 998 for untagged trafficC．It blocks VLAN 998 traffic from passing on the trunkD．It creates a VLAN 998 interfaceE．None of the above
The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?（）A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.
A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named test on that switch.Which of the following command will enable that?（）A. interface vlan 100 ip access-group test inB. interface vlan 100 ip access-group testC. vlan access-map test 100D. vlan filter test vlan-list 100
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A. The switch name must match the workgroup name of the local network.B. The switch must be configured with an IP address and default gateway.C. The remote workstations must have access to the management VLAN of the switch.D. CDP must be enabled on the switch so that it can be located by other devices on the network.
What is the function of the command switchport trunk native vlan 999 on a switch?() A. It designates VLAN 999 for untagged traffic.B. It blocks VLAN 999 traffic from passing on the trunk.C. It creates a VLAN 999 interface.D. It designates VLAN 999 as the default for all unkown tagged traffic.
Which two statements describe the Cisco implementation of VLANs?() A. VLAN 1 is the default Ethernet VLAN.B. CDP advertisements are only sent on VLAN 1002.C. By default, the management VLAN is VLAN 1005.D. By default, the switch IP address is in VLAN 1005.E. VLAN 1002 through 1005 are automatically created and cannot be deleted.
Which two statements about the configuration of the switch interface are correct (Choose two)()。 A.The switchport belongs only to VLAN 2B.Interface fa0/0 will be in both VLAN 1 (by default) and VLAN 2C.The exhibit shows interface fa0/0 to be dynamically mapped to VLAN 2D.A network host can be connected to this interface
You are the network administrator tasked with designing a switching solution for the Company network. Which of the following statements describing trunk links are INCORRECT？（）A、 The trunk link belongs to a specific VLAN.B、 Multiple trunk links are used to connect multiple end user devices.C、 A trunk link only supports native VLAN.D、 Trunk links use 802.10 to identify a VLAN.E、 The native VLAN of the trunk link is the VLAN that the trunk uses for untagged packets.
You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A、 ip routingB、 switchport mode trunkC、 no switchportD、 switchport trunk native vlan 1E、 None of the other alternatives apply
You are assigning VLANs to the ports of switch R1. What VLAN number value is an assigned tothe default VLAN？（）A、VLAN 1003B、VLAN 1C、VLAN OND、VLAN AE、VLAN 0
A user plugged a cable between two network jacks that attach to the same switch and caused a broadcast storm. Which of the following would have prevented the broadcast storm?（）A、Spanning treeB、VLAN taggingC、802.1xD、Port mirroring
Which two attributes need to match for two switches to become members of the same MST region？ （）A、the table of 4096 elements that map the respective VLAN to STP instance numberB、VTP versionC、configuration revision numberD、native VLAN ID
Which command alone will disable trunking on a Layer 2 switch port？（）A、no switchport trunk native vlan vlan-idB、switchport nonegotiateC、no switchport mode dynamic desirableD、switchport mode access
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）A、The switch must be configured with an IP address, subnet mask, and default gateway.B、The switch must be connected to a router over a VLAN trunk.C、The switch must be reachable through a port connected to its management VLAN.D、The switch console port must be connected to the Ethernet LAN.E、The switch management VLAN must be created and have a membership of at least one switch
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
单选题What is the function of the command switchport trunk native vlan 999 on a switch?（）AIt designates VLAN 999 for untagged traffic.BIt blocks VLAN 999 traffic from passing on the trunk.CIt creates a VLAN 999 interface.DIt designates VLAN 999 as the default for all unkown tagged traffic.
多选题By default, each port in a Cisco Catalyst switch is assigned to VLAN1. Which two recommendations are key to avoid unauthorized management access? （）ACreate an additional ACL to block the access to VLAN 1.BMove the management VLAN to something other than default.CMove all ports to another VLAN and deactivate the default VLAN.DLimit the access in the switch using port security configuration.EUse static VLAN in trunks and access ports to restrict connections.FShutdown all unused ports in the Catalyst switch.
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）AThe switch must be configured with an IP address, subnet mask, and default gateway.BThe switch must be connected to a router over a VLAN trunk.CThe switch must be reachable through a port connected to its management VLAN.DThe switch console port must be connected to the Ethernet LAN.EThe switch management VLAN must be created and have a membership of at least one switch
单选题A Cisco Catalyst switch is part of the CIS network. As an experienced network administrator, you are thinking of filtering the traffic within VLANI00 with the use of a VACL named "test" on that switch. Which of the following command will enable that?（）Ainterface vlan 100 ip access-group test inBinterface vlan 100 ip access-group testCvlan access-map test 100Dvlan filter test vlan-list 100
单选题An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check？（）A Default gatewayB The ports on the switchC Port security on the servers switch portD Ethernet cable
单选题Which command alone will disable trunking on a Layer 2 switch port？（）Ano switchport trunk native vlan vlan-idBswitchport nonegotiateCno switchport mode dynamic desirableDswitchport mode access
单选题You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A ip routingB switchport mode trunkC no switchportD switchport trunk native vlan 1E None of the other alternatives apply
单选题What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?（）AIt creates a VLAN 999 interface.BIt designates VLAN 999 for untagged traffic.CIt blocks VLAN 999 traffic from passing on the trunk.DIt designates VLAN 999 as the default for all unknown tagged traffic.