Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? () A. area 0 stub o n routers R4 and R5B. area 5 stub on routers R4 and R5C. area 5 stub no - summary on routers R4 and R5D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5E. area 5 stub no - summary on router R4 and area 5 stub on router R5
Refer to the exhibit. What additional commands should be used to configure OSPF area 5 as a Totally Stubby area? ()
A. area 0 stub o n routers R4 and R5
B. area 5 stub on routers R4 and R5
C. area 5 stub no - summary on routers R4 and R5
D. area 0 stub no - summary on router R4 and area 5 stub no - summary on router R5
E. area 5 stub no - summary on router R4 and area 5 stub on router R5
相关考题：
ABR R1 has been configured with an area 1 stub no － summary command. Which stubby area type is area 1?() A. StubB. Totally stubbyC. NSSAD. Totally NSSA
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）A. type 1 Router LSAB. type 2 Network LSAC. type 3 Network Summary LSAD. type 4 ASBR Summary LSAE. type 5 AS External LSAF. type 7 NSSA External LSA
Refer to the exhibit. Will redistribute d RIP routes from OSPF Area 2 be allowed in Area 1? () A. RIP routes will be allowed in Area 1 only if they are first redistributed into EIGRP.B. Because NSSA will discard type 7 LSAs, redistributed RIP routes will not be allowed in Area 1.C. Redistrib uted RIP routes will be allowed in Area 1 because they will be changed into type 5 LSAs in Area 0 and passed on into Area 1.D. Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 7 LSAs in Area 0 and passed on into Area 1.E. Because Area 1 is an NSSA, redistributed RIP routes will not be allowed.
Refer to the exhibit. Router C was configured so that it could form an adja cency with three OSPF neighbors, one connected to each of its three physical interfaces. Which statement is correct about router C?（）A. It is configured and functioning correctly as an OSPF internal router.B. It is configured and functioning correc tly as an ABR attached to stub area 4.C. It is configured and functioning correctly as an ASBR attached to external area 4.D. It is configured and functioning correctly as an ABR attached to totally stubby area 4.E. It is not configured correctly to function as specified.
To make OSPF area 4 totally stubby, the following command was issued on the ABR in router configuration mode: area 4 stub.Which two things need to be done to finish making area 4 a totally stubby area?（）A. Apply the area 4 stub command to all routers in the areaB. On the ABR, use the area 4 stub command with the no - summary keywordC. On the ABR, specify a default cost for the area with the area default - cost commandD. On the ABR, use the default - information originate command to inject a default route into area 4E. Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas
Refer to the exhibit. What is the effect of the OSPF configuration on router B?() A. All interfaces will be in area 0B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2
Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? () A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.E. The Hello parameters on routers R1 and R2 do not m atch.
Refer to the exhibit. What two statements are true?() A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.
Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?() A. On the ABR router ospf 10 area 3 stubB. On all Area 3 routers router ospf 10 area 3 stubC. On all Area 3 routers router ospf 10 area 3 stub no - summaryD. On the ABR router ospf 10 area 3 nssaE. On the ABR rou ter ospf 10 area 3 stub no - summary
You are troubleshooting an OSPF problem where external routes are not showing up in the OSPF database. Which two options a re valid checks that should be performed first to verify proper OSPF operation?（）A、Are the ASBRs trying to redistribute the external routes into a totally stubby area?B、Are the ABRs configured with stubby areas?C、Is the subnets keyword being used with the redistribution command?D、Is backbone area (area 0) contiguous?E、Is the CPU utilization of the routers high?
When verifying the OSPF link state database, which type of LSAs should you expect to see within the different OS PF area types?（）A、All OSPF routers in stubby areas can have type 3 LSAs in their database.B、All OSPF routers in stubby areas can have type 7 LSAs in their database.C、All OSPF routers in totally stubby areas can have type 3 LSAs in their database.D、All OSPF routers in totally stubby areas can have type 7 LSAs in their database.E、All OSPF routers in NSSA areas can have type 3 LSAs in their database.F、All OSPF routers in NSSA areas can have type 7 LSAs in their database.
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、TestKingRouter(config)# router ospf 0B、TestKingRouter(config)# router ospf 1C、TestKingRouter(config)# router ospf area 0D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
ABR R1 has been configured with an area 1 stub no - summary command. Which stubby area type is area 1?（）A、StubB、Totally stubbyC、NSSAD、Totally NSSA
相对于OSPF的stub area, OSPF的totally stubby area有何不同（）A、不接收类型5的LSAs.B、是一个思科专有的特性C、不接收汇聚的链路状态广播D、应用了路由重注入
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0E、Router(config-router)#network 192.168.16.0 0.0.0.255 0F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Cat6500（config）# router ospf 1 Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0 Cat6500（config-router）# nsf Cat6500（config-router）#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational. What is the most likely reason？ （）A、CEF was not properly configured.B、OSPF was not properly configured for graceful restart.C、Stateful switchover was not correctly configured.D、NSF for OSPF is only supported in area 0.
An OSPF non-backbone area allows external routes to be flooded within the area. These externalroutes are propagated into other areas. However, external routes from other areas are not allowed to enter this area. Which type of OSPF area does this describe?（）A、stub areaB、transit areaC、border areaD、not-so-stubby area
多选题Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）ATestKingRouter(config)# router ospf 0BTestKingRouter(config)# router ospf 1CTestKingRouter(config)# router ospf area 0DTestKingRouter(config)# network 192.168.16.0 0.0.0.255 0ETestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0FTestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0
多选题相对于OSPF的stub area, OSPF的totally stubby area有何不同（）A不接收类型5的LSAs.B是一个思科专有的特性C不接收汇聚的链路状态广播D应用了路由重注入
多选题You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriate ARB. Which two commands should you use from the [edit] hierarchy level within the JUNOS software configuration mode？（）Aset protocols ospf area-range network/mask-lengthBset protocols ospf area area-id nssa area-range network/mask-lengthCset protocols ospf area area-id area-range network/mask-length restrictDset protocols ospf area area-id nssa area-range network/mask-length restrict
多选题To make OSPF area 4 totally stubby, the following command was issued on the ABR in router configuration mode: area 4 stub.Which two things need to be done to finish making area 4 a totally stubby area?（）AApply the area 4 stub command to all routers in the areaBOn the ABR, use the area 4 stub command with the no - summary keywordCOn the ABR, specify a default cost for the area with the area default - cost commandDOn the ABR, use the default - information originate command to inject a default route into area 4EUse the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas
多选题Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）ARouter（config）#router ospf 1BRouter（config）#router ospf 0CRouter（config）#router ospf area 0DRouter（config-router）#network 192.168.16.0 0.0.0.255 area 0ERouter（config-router）#network 192.168.16.0 0.0.0.255 0FRouter（config-router）#network 192.168.16.0 255.255.255.0 area 0
多选题You are troubleshooting an OSPF problem where external routes are not showing up in the OSPF database. Which two options a re valid checks that should be performed first to verify proper OSPF operation?（）AAre the ASBRs trying to redistribute the external routes into a totally stubby area?BAre the ABRs configured with stubby areas?CIs the subnets keyword being used with the redistribution command?DIs backbone area (area 0) contiguous?EIs the CPU utilization of the routers high?
多选题You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriateABR. Which two commands should you use from the [edit] hierarchy level within JUNOS configuration mode?（）Aset protocols ospf area-range network/mask-lengthBset protocols ospf area area-id nssa area-range network/mask-lengthCset protocols ospf area area-id area-range network/mask-length restrictDset protocols ospf area area-id nssa area-range network/mask-length restrict