Refer to the exhibit. Router RTA has been configured as a DHCP server. The two debug commands will generate output on RTA when Ho st A requests an IP address. Which set of DHCPD debug messages is in the correct sequence?（）A.DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to clientB.DH CPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: Sending DHCPACK to clientC.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to clientD.DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to clientE.DHCPD: Sending DHCPACK to client DHCPD: DHCPD ISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from clientF.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
Refer to the exhibit. Router RTA has been configured as a DHCP server. The two debug commands will generate output on RTA when Ho st A requests an IP address. Which set of DHCPD debug messages is in the correct sequence?（）
A.DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to client
B.DH CPD: DHCPDISCOVER received from client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: Sending DHCPACK to client
C.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPACK to client
D.DHCPD: DHCPREQUEST received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client
E.DHCPD: Sending DHCPACK to client DHCPD: DHCPD ISCOVER received from client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
F.DHCPD: DHCPDISCOVER received from client DHCPD: Sending DHCPACK to client DHCPD: Sending DHCPOFFER to client DHCPD: DHCPREQUEST received from client
相关考题：
Refer to the exhibit. The routing protocols EIGRP and OSPF have been configured as indicated in the exhibit. Given the partial configuration of router R2, which network will be present in th e routing table of R4?（）A. Network BB. Network A and Network BC. Network AD. neither Network A nor Network B
Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253
Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? () A.The NProuter has two OSPF neighbors in the Full adjacency stateB.The NProuter serial0/0 interface has the OSPF dead timer set to 10 secondsC.The NProuter serial0/0 interface has been configured with an OSPF network type of pointtopointD.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers settingE.The Mismatched error is caus ed by the expiration of the OSPF timers
Refer to the exhibit. Which two statements are true?() A. DHCPDISCOVER packets will reach the DHCP server.B. The router will not forward DHCPDIS COVER packets because it has not been configured to do so.C. This configuration is applied to interface Fa0/1.D. DHCPDISCOVER packets will not reach the DHCP server because DHCPDISCOVER packets are broadcasts.E. DHCPDISCOVER packets will not reach the DHCP server because ports 67 and 68 have not been explicitly allowed by the ip forward - protocol command.F. This configuration is applied to interface Fa0/0.
Refer to the exhibit. Which statement is true about the router configuration that is shown ?Select the best response.() A. Additional DHCP options will be imported from another DHCP server.B. The DHCP server pools need to be bound to an interface to operate.C. This configuration will provide IP configuration information to two different su bnets.D. Additional DCHP option information needs to be imported from another DHCP server.E. If the router hands out all the addresses in pool 1, then it will supply addresses from pool 2.
Refer to the exhibit. On the basis of the output, what two conclusions can be reached?() A. The default administrative distance has been changed.B. IS - IS is not enabled.C. Three physical interfaces are taking part in integrated IS - IS.D. IS - IS is not redistributing any oth er routing protocols.E. There are two neighboring routers sending IS - IS routing information.F. Address summarization is configured.
Refer to the exhibit. Which two conclusions can be drawn from the debug ip igmp output?() A. The router sent an IGMP version 2 query out interface Ethernet1 at multicast address 224.0.0.1.B. Router RTA received an IGMP report version 1 from host 192.168.9.1.C. Reverse Path Forwarding (RPF) is ena bled for 192.168.9.4.D. Reverse Path Forwarding (RPF) is enabled for 224.0.1.40.E. The IP multicast groups are 224.0.0.1, 224.0.1.40, and 239.255.0.1.F. IP PIM RP mapping is static.
Refer to the exhibit. What two statements are true?() A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.
Refer to the exhibit. Which st atement is true?() A. Router RTA is the BDRB. Router RTA is directly connected to interface 192.168.45.1C. Neighbor 192.168.45.1 has changed its OSPF priority numberD. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?() A. The no auto - summary command has not been issued under the EIGRP process on both routers.B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）A.Check and change the access lists on router RTAB.Configure the auto summary command under router eigrp 1 on router RTAC.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterfaceD.Issue the no ip split horizon command on router RTAE.Issue the no ip split horizon eigrp 1 command on router RTAF.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?() A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1B. R4(config)# ip default - network 10.0.0.0C. R4(config - router)# default -information originateD. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A. oneB. threeC. twoD. zero
Refer to the exhibit. Switch port FastEthernet 0/24 on AlSwitch1 will be used to create an IEEE 802.1Q- complaint trunk to another switch. Based on the output shown, What is the reason the trunk does not form, even thought the proper cabling has been attached?（）A.VLANs have not been created yetB.An IP address must be configured for the portC.The port is currently configured for access modeD.The correct encapsulation type has not been configuredE.The no shutdown command has not been entered for the port
Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）A、As numbers must be changed to match on all the routers.B、Loopback interface must be configured so a DR is elected.C、The no auto-summary command is needed on Router A and Router C.D、Router B needs to have two network statements, one for each connected network.
Refer to the exhibit. Which statement is correct based on the show login command output shown？（）A、When the router goes into quiet mode， any host is permitted to access the router via Telnet，SSH， and HTTP，since the quiet-mode access list has not been configured.B、The login block-for command is configured to block login hosts for 93 seconds.C、All logins from any sources are blocked for another 193 seconds.D、Three or more login requests have failed within the last 100 seconds.
A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.B、For the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.C、Direct inter-vlan communication does not require OSPFD、OSPF cannot be used if router-on-a-stick is configured on the router
How can an administrator determine if a router has been configured when it is first powered up?（）A、A configured router prompts for a passwordB、A configured router goes to the privileged mode promptC、An un configured router goes into the setup dialogD、An un configured router goes to the enable mode prompt
Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）A、The router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2B、The configuration is invalid because the DHCP options are global configuration commandsC、The configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesD、The router will choose which pool to use based upon the interface the DHCP request wasreceived on
HSRP has been configured between two Company devices. What kind of message does an HSRP configured router send out every 3 seconds？（）A、 RetireB、 CoupC、 ResignD、 SendE、 Hello
A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）A、oneB、threeC、twoD、zero
单选题Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）A 10.1.1.2B 10.154.154.1C 172.16.5.1D 192.168.5.3
单选题Refer to the exhibit. Which statement is correct based on the show login command output shown？（）AWhen the router goes into quiet mode， any host is permitted to access the router via Telnet，SSH， and HTTP，since the quiet-mode access list has not been configured.BThe login block-for command is configured to block login hosts for 93 seconds.CAll logins from any sources are blocked for another 193 seconds.DThree or more login requests have failed within the last 100 seconds.
单选题HSRP has been configured between two Company devices. What kind of message does an HSRP configured router send out every 3 seconds？（）A RetireB CoupC ResignD SendE Hello
多选题Refer to the exhibit. On the basis of the information in the exhibit， which two statements are true？（）AWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose2 because of the higher MED value of SanJose2BThe serial 0/0/1 interface on the ISP router has been configured with the set metric 50commandCThe output was generated by entering the show ip bgp command on the SanJose1 routerDThe output was generated by entering the show ip bgp command on the ISP routerEThe serial 0/0/1 interface on the ISP router has been configured with the set metric 75commandFWhen traffic is sent from the ISP to autonomous system 64512， the traffic will be forwarded toSanJose1 because of the lower MED value of SanJose1
单选题Refer to the exhibit. The DHCP configuration that is shown is configured on a Cisco router. Whichstatement is true？（）AThe router will distribute IP addresses from pool 1 until its addresses are exhausted. Then therouter will begin distributing addresses from pool 2BThe configuration is invalid because the DHCP options are global configuration commandsCThe configuration is incomplete until the DHCP pools are bound to the appropriate interface orinterfacesDThe router will choose which pool to use based upon the interface the DHCP request wasreceived on
单选题A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）AFor the two vlans to communicate，a network statement for the trunk interface needs to be added to the OSPF configuration.BFor the two vlans to communicate， a network statement for each subinterface needs to be added to the OSPF configuration.CDirect inter-vlan communication does not require OSPFDOSPF cannot be used if router-on-a-stick is configured on the router