Which method should be used to warm up the pump turbines prior to discharge ________．A.Lock the turbine rotor and slowly bleed in steam until operating temperature is reachedB.Run the pump at high speed with the discharge valves closedC.Run the turbine at slow speed with the pump disconnectedD.Shut the discharge valve and run the pump at slow speed
Which method should be used to warm up the pump turbines prior to discharge ________．
A.Lock the turbine rotor and slowly bleed in steam until operating temperature is reached
B.Run the pump at high speed with the discharge valves closed
C.Run the turbine at slow speed with the pump disconnected
D.Shut the discharge valve and run the pump at slow speed
相关考题：
Which of the following terms is used to identify the pressure of the liquid entering a pump?A.Suction headB.Pump headC.Discharge headD.Total head
Which of the following will be the advantage of a centrifugal pump as compared with a reciprocating pump? l.Its discharge is continuous; ll.It has no internal valves: lll.Upon accidental closing of discharge valve, excessive pressure will not build up()A.l, llB.ll, lllC.l ,ll.IIID.llonly
Consider the following table:Which method should used to add a new g201305 partition to the table?() A.AB.BC.CD.DE.E
While on watch in the engine room, you hear a continuous sounding of the general alarm. Which of the following actions should you take?A.Make an entry in the official logbookB.Open the master control valves on the fixed CO2 systemC.Start the fire pump and check discharge pressureD.Secure auxiliary condenser overboard discharge
Which install method should be used to recycle an LPAR without retaining any information from its original configuration?() A.MigrationB.PreservationC.New and Complete OverwriteD.Alternate disk installation
A spur gear pump should be operated with the discharge valves ______.A.slightly openedB.throttledC.fully openedD.halfway opened
If it becomes necessary to pump bilges while a vessel is in port, which of the following procedures should be followed?A.Pump only if the discharge is led to a shore tank or bargeB.Pump only during the hours of darknessC.Pump only on the outgoing tideD.Pump only as much as is necessary
If you must pump bilges while a vessel is in port，you should pump only ______．A.If discharge is led to a shore tank or bargeB.During the hours of darknessC.On the outgoing tideD.As much as is necessary
During which phase of the steps to success methodology for Cisco SMB Security Solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which，if any modification should be prior to implementation？（）A、PrepareB、DesignC、PositionD、DevelopE、PlanF、Perform
Which install method should be used to recycle an LPAR without retaining any information from its original configuration？（） A、MigrationB、PreservationC、New and Complete OverwriteD、Alternate disk installation
单选题In （） pump a closed discharge valve will not cause excessive pressure to build up.AgearBvaneCscrewDcentrifugal
单选题What is a function of the wearing rings used in most centrifugal pumps?（）AAbsorb erosion of high velocity discharge streamBSeal pump shaft against entry of airCIsolate the discharge side from the suction sideDDampen the turbulent discharge flow
单选题Which of the following will be the advantage of a centrifugal pump as compared with a reciprocating pump?（） (1) Its discharge is continuous (2) It has no internal valves (3) Upon accidental closing of discharge valve, excessive pressure will not build upA（1），（2）B（2），（3）C（1），（2），（3）D（2）only
单选题Which method should be used to warm up the pump turbines prior to discharge（）.ALock the turbine rotor and slowly bleed in steam until operating temperature is reachedBRun the pump at high speed with the discharge valves closedCRun the turbine at slow speed with the pump disconnectedDShut the discharge valve and run the pump at slow speed
单选题During which phase of the steps to success methodology for Cisco SMB Security Solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which，if any modification should be prior to implementation？（）APrepareBDesignCPositionDDevelopEPlanFPerform
单选题Most pump manufacturers recommended that the discharge piping for centrifugal pumps be （）.Aone size larger than the pump discharge nozzleBthe same size as the pump discharge nozzleCone size smaller than the pump discharge nozzleDinstalled with a short radius elbow at the pump
单选题During which phase of the steps to success methodology for Cisco SMB security solutions would the Network Readiness Assessment be used to assess the readiness of an existing network infrastructure and determine which， if any， modification should be made prior to implementation？（）APositionBPrepareCDesignDPerformEPlan
单选题To operate a centrifugal fire pump at reduced capacity, you should （）.Areadjust the relief valveBthrottle the suction lineCthrottle the discharge valveDopen the priming line
单选题If it becomes necessary to pump bilges while a vessel is in port, which of the following procedures should be followed?（）APump only if the discharge is led to a shore tank or bargeBPump only during the hours of darknessCPump only on the outgoing tideDPump only as much as is necessary
单选题Which of the listed statements is correct concerning the starting of centrifugal pumps?（）AThey should always be started with the discharge valve closedBThey should always be started with the discharge valve openedCA priming pump is always required to flood the impeller suctionDThey should always be started with the sealing line valves closed
单选题The terminal indicates to you that they are going to use a booster pump to assist the discharging operation. You start the discharge，and in a few minutes the pressure drops sharply. This could be a result of the（）.Abooster pump coming on the line and discharging properlyBbooster pump failing to startCbooster pump being lined up in the wrong directionDship's pump speeding up
单选题A relief valve for a cargo pump is generally installed（）.Aafter the discharge valveBbetween the pump and discharge valveCafter the suction valveDbetween the pump and suction valve
单选题If a bilge pump failed to build up discharge pressure, you should check for （）.Aexcessive water in the bilgesBa clogged suction strainerCoil in the bilgesDAll of the above
单选题Which method should be used to dynamically elect an RP when your network is using PIM version1?（）Aauto-RPBstatic RPCdiscovery modeDbootstrap protocol
单选题When starting a centrifugal pump, the discharge valve should be （）.AclosedBopened fullyCcracked openDpartly open
单选题The simplest method to use for determining if a centrifugal pump is operating as designed, is to （）.Aclosely observe the pump discharge temperatureBclose off the discharge valve, and watch for a rise in pressureCmomentarily close off the suction valve, and watch for a rise in pressureDuse a clamp on ammeter and compare the readings to past records
单选题With reference to operating a four-ram steering gear system under emergency conditions, which one of the following statements is incorrect?（）AOnly one pump should be used at any timeBThe ship speed should be reduced to 70% of the normalCWatch keeping of the steering gear should be increasedDLimitations of the steering gear should be logged but the bridge need not be informed