What is the reason for configuring a passive interface on a router?() A. Allows interfaces to share common IP addresses.B. Allows an interface to remain up without the aid of keepalives.C. Allows a router to send routing and not receive updates via that interface.D. Allows a routing protocol to forward updates that is missing its IP address.E. Allows a router to receive routing updates on an interface but not send updates via that interface.
What is the reason for configuring a passive interface on a router?()
A. Allows interfaces to share common IP addresses.
B. Allows an interface to remain up without the aid of keepalives.
C. Allows a router to send routing and not receive updates via that interface.
D. Allows a routing protocol to forward updates that is missing its IP address.
E. Allows a router to receive routing updates on an interface but not send updates via that interface.
相关考题：
如果不想公布网络中的某些RIP信息，那么可以采用被动接口配置。将路由器RouterA的FastEthernet0/0接口设置为被动接口的配置语句是( )。A) RouterA(Config-if)#rip passive-interfaceB) RouterA(Config-if)#passive-interface ripC) RouterA(Config)#passive-interface fastethernet0/0D) RouterA(Config-router)#passive-interface fastethernet0/0
如果不想公布网络中的某些RIP信息，那么可以采用被动接口配置。将路由器RouterA的FastEthemet0／0接口设置为被动接口的配置语句是——。A．RouterA(Config—if)#passive—interface ripB．RouterA(Config)}}passive—interface fastethemet0／0C．RouterA(Config—router)#passive—interface fastethemet0／0D．RouterA(Config—if)#rip passive—interface
如果不想公布网络中的某些RIP信息，那么可以采用被动接口配置。将路由器RouterA的FastEthernet0/0接口设置为被动接口的配置语句是______。A．RouterA(Config-router) #passive-interface fastethernet0/0B．RouterA(Config-if) #passive-interface ripC．RouterA(Config) #passive-interface fastethernet0/0D．RouterA(Config-if) #rip passive-interface
When configuring PPP over ATM interfaces, what does the profile utility accomplish?() A.It binds an interface to a virtual router.B.It allows for dynamic interface creation.C.It assigns a Domain Name Server for a session.D.It identifies the RADIUS server to use for authentication
Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive － interface router configuration command is entered?() A. EIGRPB. RIPC. OSPFD. IS - IS
Which three route filtering statements are true?() A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）A. Declare router B a stub router using the eigrp stub command.B. Use the passive - interface command for interface Serial0/0/0.C. Use a mask with the network command to exclude interface Serial0/0/0.D. Implement a distribute list to exclude the link prefix from the routi ng updates.
When configuring a serial interface on a router, what is the default encapsulation?() A. atm-dxiB. frame-relayC. hdlcD. lapbE. ppp
如果不想公布网络中的某些RIP信息，可以采用被动接口配置。将路由器Router A的FastEthemet0/0接口设置为被动接口的配置语句是( )。A．RouterA (Config-if) # passive-interfaceB．RouterA (Config-if) # passive-interface ripC．RouterA (Config) # passive-interface fastethernet0/0D．RouterA (Config-router) # passive-interface fastethernet0/0
What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）A、Route reflectors are not passing updates properly.B、BGP synchronization has been enabled.C、The next-hop address is unreachable.D、No loopback interface has been configured on a router.
When configuring a serial interface on a router, what is the default encapsulation?（）A、atm-dxiB、frame-relayC、hdlcD、lapbE、ppp
Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive - interface router configuration command is entered?（）A、EIGRPB、RIPC、OSPFD、IS - IS
A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29. which statement explains the reason for this issue？（）A、The address is abroadcast address.B、The Ehernet interface is faulty.C、VLSM-capable routing protocols must be enable first on the router.D、This address is a network address.
A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29.which statement explains the reason for this issue?（）A、The address is a broadcast addressB、The Ehernet interface is faultyC、VLSM-capable routing protocols must be enable first on the router.D、This address is a network address.
The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）A、The Popcorn router is not forwarding RIP updates.B、The Popcorn router did not include network 192.168.12.0 in its routing configuration.C、The Ethernet1 interface of the Popcorn router is shutdown.D、The clockrate is not present in the configuration of one of the routers.E、The Serial interface of the Popcorn router is not operating.
What is the reason for configuring a passive interface on a router?（）A、Allows interfaces to share common IP addresses.B、Allows an interface to remain up without the aid of keepalives.C、Allows a router to send routing and not receive updates via that interface.D、Allows a routing protocol to forward updates that is missing its IP address.E、Allows a router to receive routing updates on an interface but not send updates via that interface.
Which three route filtering statements are true?（）A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interfaceB、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interfaceC、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interfaceD、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interfaceE、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interfaceF、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
What is true about access control on bridged and routed VLAN traffic？ （）A、 Router ACLs can be applied to the input and output directions of a VLAN interface.B、 Bridged ACLs can be applied to the input and output directions of a VLAN interface.C、 Only router ACLs can be applied to a VLAN interface.D、 VLAN maps and router ACLs can be used in combination.E、 VLAN maps can be applied to a VLAN interface
What must be set correctly when configuring a serial interface so that higher-level protocols calculate the best route?（）A、bandwidthB、delayC、loadD、reliability
Which RIP configuration command allows the ERX Edge Router to send Unicast updates to configured neighbors?（）A、neighborB、unicast-neighborC、triggered-updateD、passive-interface
When configuring PPP over ATM interfaces, what does the profile utility accomplish?（）A、It binds an interface to a virtual router.B、It allows for dynamic interface creation.C、It assigns a Domain Name Server for a session.D、It identifies the RADIUS server to use for authentication
多选题The Peanut router is able to successfully ping the Serial 0 and Ethernet 0 interface of the Popcorn router, but a ping issued to the Ethernet 1 interface fails. Based on the above output, what are the potential causes of this problem?（）AThe Popcorn router is not forwarding RIP updates.BThe Popcorn router did not include network 192.168.12.0 in its routing configuration.CThe Ethernet1 interface of the Popcorn router is shutdown.DThe clockrate is not present in the configuration of one of the routers.EThe Serial interface of the Popcorn router is not operating.
单选题Which routing protocol will continue to receive and process routing updates f rom neighbors after the passive - interface router configuration command is entered?（）AEIGRPBRIPCOSPFDIS - IS
单选题When configuring a serial interface on a router, what is the default encapsulation?（）Aatm-dxiBframe-relayChdlcDlapbEppp
单选题When configuring PPP over ATM interfaces, what does the profile utility accomplish?（）AIt binds an interface to a virtual router.BIt allows for dynamic interface creation.CIt assigns a Domain Name Server for a session.DIt identifies the RADIUS server to use for authentication
单选题A network administrator receives an error message while tring to configure the Ethernet interface of a router with IP address 10.24.24.24/29.which statement explains the reason for this issue?（）AThe address is a broadcast addressBThe Ehernet interface is faultyCVLSM-capable routing protocols must be enable first on the router.DThis address is a network address.
单选题What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）ARoute reflectors are not passing updates properly.BBGP synchronization has been enabled.CThe next-hop address is unreachable.DNo loopback interface has been configured on a router.