As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?() A. TestKSwitch(config)# ip route-default 192.168.1.115B. TestKSwitch(config)# ip default-gateway 192.168.1.115C. TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0D. TestKSwitch(config)# ip default-network 192.168.1.115
As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?()
A. TestKSwitch(config)# ip route-default 192.168.1.115
B. TestKSwitch(config)# ip default-gateway 192.168.1.115
C. TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0
D. TestKSwitch(config)# ip default-network 192.168.1.115
相关考题：
As a Ezonexam trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?A．TestKSwitch(config)# ip route-default 192.168.1.115B．TestKSwitch(config)# ip default-gateway 192.168.1.115C．TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0D．TestKSwitch(config)# ip default-network 192.168.1.115E．None of the above
You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?() A. Switch(config)# ip default-network 192.168.12.1B. Switch(config)#ip route-default 192.168.12.1C. Switch(config)# ip default-gateway 192.168.12.1D. Swicth(config)# ip route 192.168.12.1 0.0.0.0
You work as a network engineer at TestKing.com. You are required to allow establishment of a Telnet session with a router TestKingC.Which set command must be configured?() A.B.C.D.E.F.
You are configuring a Cisco multilayer switch for the Company network. Which command would you use to configure a port to act as a routed interface？（）A、 ip routingB、 switchport mode trunkC、 no switchportD、 switchport trunk native vlan 1E、 None of the other alternatives apply
You are a technician at TestKing. Your assistant applied an IP access control list to Router TK1. You want to check the placement and direction of the access control list.Which command should you use?（）A、show access-listB、show ip access-listC、show ip interfaceD、show interfaceE、show interface list
You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?（）A、Switch(config)# ip default-network 192.168.12.1B、Switch(config)#ip route-default 192.168.12.1C、Switch(config)# ip default-gateway 192.168.12.1D、Swicth(config)# ip route 192.168.12.1 0.0.0.0
You work as a technician at TestKing. You are configuring a Cisco router. You want to configure the IP address on an interface.Which command should you use?（）A、router(config-if)#ip address 142.8.2.1 subnet mask 255.255.252.0B、router(config-if)#142.8.2.1 0.0.3.255C、router(config-if)#ip address 142.8.2.1 255.255.252.0D、router(config-if)#142.8.2.1 subnet mask 255.255.252.0E、router(config-if)#ip address 142.8.2.1 0.0.3.255F、router(config-if)#ip address 142.8.2.1 subnet mask /22
Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software?（）A、show port networkB、 show running-configC、show controllers Ethernet-controllerD、 show interfaces
You are a systems administrator and you are about to assign static IP addresses to various servers on your network. For the network 192.168.20.24/29 the router is assigned to the first usable host address, while the last usable host address goes to your Sales server. Which one of the following commands would you enter into the IP properties box of the sales server?（）A、IP address: 192.168.20.14 Subnet Mask: 255.255.255.248 Default Gateway:192.168.20.9B、IP address: 192.168.20.254 Subnet Mask: 255.255.255.0 Default Gateway:192.168.20.1C、IP address: 192.168.20.30 Subnet Mask 255.255.255.248 Default Gateway:192.168.20.25D、IP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.17E、IP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.25
Which command can you use to determine the cisco ios feature set on a cisco router？（）A、show versionB、dir flash：include iosC、show environmentD、show diagE、show inventory
When you enable port security on an interface that is also configured with a voice VLAN， what is the maximum number of secure MAC addresses that should be set on the port？（）A、No more than one secure MAC address should be set.B、The default will be set.C、The IP phone should use a dedicated port， therefore only one MAC address is needed per port.D、No value is needed if the switchport priority extend command is configured. E、No more than two secure MAC addresses should be set.
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）A、The switch name must match the workgroup name of the local network.B、The switch must be configured with an IP address and default gateway.C、The remote workstations must have access to the management VLAN of the switch.D、CDP must be enabled on the switch so that it can be located by other devices on the network.
An administrator is testing setting the IP address on a Linux server from command line. Which of the following commands is used to set the default gateway for the server？（）A、routeB、tracerouteC、ipconfigD、nmap
Your network contains a computer named Computer1. Computer1 is assigned an IP address of 39 / 84 192.168.1.112/26.Your companys corporate policy states that the first usable address in each subnet is allocated to the default gateway.You need to configure the default gateway for Computer1.Which address should you choose？（）A、192.168.1.1B、192.168.1.63C、192.168.1.65D、192.168.1.93
You dial-in to your company’s network from home. You notice that you can only access resources only on the first subnet （where the Dial-In Server is located）， but cannot go beyond that. What Dial-In setting should you change？（）A、 IP addressB、 Check the "Use default gateway on remote network" checkboxC、 Disable "Use IP compression"D、 On the WINS tab of the TCP/IP Settings， check the "Use NetBIOS setting from the DHCP-Server"E、 On the DNS tab of TCP/IP settings， check the "Register this connections address in the DNS" checkbox
Your network contains a server named Server1. Server1 runs Windows Server 2008 R2 and has a single network connection. The connection is configured to use a default gateway address of 10.0.0.1.The default gateway has a metric value of 100.You configure a second default gateway that uses an address of 10.0.0.2.You need to ensure that 10.0.0.2 is only used as the default gateway if 10.0.0.1 is unreachable. What should you do？（）A、For the interface, set the interface metric to 100.B、For the 10.0.0.2 gateway, set the metric to 50.C、For the 10.0.0.2 gateway, set the metric to 200.D、For the 10.0.0.1 gateway and the 10.0.0.2 gateway, enable automatic metric.
Network topology exhibit: You are the administrator at ExamSheet.net. You use TCP/IP as the only protocol on your network. The network is configured as in the network topology exhibit. All existing computers and devices use 255.255.240.0 as the subnet mask. You install Windows 2000 Professional on a computer named ExamSheet2. You configure ExamSheet2 to have a TCP/IP address of 10.10.20.234, a default gateway of 10.10.20.1, a subnet mask of 255.255.0.0 and a WINS server address of 10.10.13.10. You cannot connect to shared resources on ExamSheetB by using its UNC name. You want ExamSheet2 to be able to connect to ExamSheetB. What should you do? （）A、Install a WINS server on the same segment as Company2B、Install and configure a DNS server and configure Company2 to use the DNS Server service.C、Configure Company2 with a default gateway address 10.10.13.1.D、Configure Company2 with a default gateway address of 10.10.30.1.E、Configure Company2 with a TCP/IP address of 10.10.20.234.
Your network consists of a single Active Directory domain named nwtraders.com. All network servers run Windows Server 2003 Service Pack 2 (SP2).The relevant IP configuration for the network is configured as shown in the following table. DC1 contains an Active Directory-integrated zone for nwtraders.com.From Server2, you run the Ping 172.26.26.11 command and receive a request timed out error message. From Server2, you run the Ping 172.16.16.129 command and receive a reply. You need to ensure that you can join Server2 to the nwtraders.com domain. What should you do?（） A、Set the IP address to 172.16.16.2.B、Set the subnet mask to 255.255.255.128.C、Set the default gateway address to 172.16.16.129.D、Set the preferred DNS server address to 172.16.16.130.
多选题You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）AThe switch name must match the workgroup name of the local network.BThe switch must be configured with an IP address and default gateway.CThe remote workstations must have access to the management VLAN of the switch.DCDP must be enabled on the switch so that it can be located by other devices on the network.
单选题When configuring a routed port on a Cisco multilayer switch， which of these is a required configuration task that you must perform to enable that port to function as a routed port？ （）AEnable the switch to participate in routing updates from external devices with the router command in global configuration mode.BEnter the no switchport command to disable Layer 2 functionality at the interface level.CEach port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.DRouting is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
单选题You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?（）ASwitch(config)# ip default-network 192.168.12.1BSwitch(config)#ip route-default 192.168.12.1CSwitch(config)# ip default-gateway 192.168.12.1DSwicth(config)# ip route 192.168.12.1 0.0.0.0
单选题You are a systems administrator and you are about to assign static IP addresses to various servers on your network. For the network 192.168.20.24/29 the router is assigned to the first usable host address, while the last usable host address goes to your Sales server. Which one of the following commands would you enter into the IP properties box of the sales server?（）AIP address: 192.168.20.14 Subnet Mask: 255.255.255.248 Default Gateway:192.168.20.9BIP address: 192.168.20.254 Subnet Mask: 255.255.255.0 Default Gateway:192.168.20.1CIP address: 192.168.20.30 Subnet Mask 255.255.255.248 Default Gateway:192.168.20.25DIP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.17EIP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.25
单选题Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software?（）Ashow port networkB show running-configCshow controllers Ethernet-controllerD show interfaces
单选题As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?（）ATestKSwitch(config)# ip route-default 192.168.1.115BTestKSwitch(config)# ip default-gateway 192.168.1.115CTestKSwitch(config)# ip route 192.168.1.115 0.0.0.0DTestKSwitch(config)# ip default-network 192.168.1.115
单选题Which command can you use to determine the cisco ios feature set on a cisco router？（）Ashow versionBdir flash：include iosCshow environmentDshow diagEshow inventory
单选题You are a technician at TestKing. Your assistant applied an IP access control list to Router TK1. You want to check the placement and direction of the access control list.Which command should you use?（）Ashow access-listBshow ip access-listCshow ip interfaceDshow interfaceEshow interface list
单选题When you enable port security on an interface that is also configured with a voice VLAN， what is the maximum number of secure MAC addresses that should be set on the port？（）ANo more than one secure MAC address should be set.BThe default will be set.CThe IP phone should use a dedicated port， therefore only one MAC address is needed per port.DNo value is needed if the switchport priority extend command is configured. ENo more than two secure MAC addresses should be set.
单选题You work as a technician at TestKing. You are configuring a Cisco router. You want to configure the IP address on an interface.Which command should you use?（）Arouter(config-if)#ip address 142.8.2.1 subnet mask 255.255.252.0Brouter(config-if)#142.8.2.1 0.0.3.255Crouter(config-if)#ip address 142.8.2.1 255.255.252.0Drouter(config-if)#142.8.2.1 subnet mask 255.255.252.0Erouter(config-if)#ip address 142.8.2.1 0.0.3.255Frouter(config-if)#ip address 142.8.2.1 subnet mask /22