You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?() A. Switch(config)# ip default-network 192.168.12.1B. Switch(config)#ip route-default 192.168.12.1C. Switch(config)# ip default-gateway 192.168.12.1D. Swicth(config)# ip route 192.168.12.1 0.0.0.0
You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?()
A. Switch(config)# ip default-network 192.168.12.1
B. Switch(config)#ip route-default 192.168.12.1
C. Switch(config)# ip default-gateway 192.168.12.1
D. Swicth(config)# ip route 192.168.12.1 0.0.0.0
相关考题：
As a Ezonexam trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?A．TestKSwitch(config)# ip route-default 192.168.1.115B．TestKSwitch(config)# ip default-gateway 192.168.1.115C．TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0D．TestKSwitch(config)# ip default-network 192.168.1.115E．None of the above
You need to configure a default route on a Ezonexam router. Which command will configure a default route on a router?A．VE1(config)# ip route 0.0.0.0 10.1.1.0 10.1.1.1B．VE1(config)# ip default-route 10.1.1.0C．VE1(config)# ip default-gateway 10.1.1.0D．VE1(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
How can you reset your router or switch to factory defaults?() A.reset configurationB.load factory-defaultC.load override defaultD.set default configuration
If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?() A. ip default-gateway 0.0.0.0B. ip route 172.16.2.1 0.0.0.0 0.0.0.0C. ip default-network 0.0.0.0D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?() A.Switch3B.Switch4C.Switch2D.Switch1
You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?（）A、Switch(config)# ip default-network 192.168.12.1B、Switch(config)#ip route-default 192.168.12.1C、Switch(config)# ip default-gateway 192.168.12.1D、Swicth(config)# ip route 192.168.12.1 0.0.0.0
In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?（）A、Two switches are connected via a trunk. Both switches have been assigned an IP address, subnet mask, and default gateway. A ping is successful between the two switches. However, VLAN information is not passed from one switch to the other switch.B、A router and a switch have been assigned an IP address, a subnet mask, and a default gateway. They are directly connected, but a ping between the two devices fails.C、A router connects to another router through a serial interface. Both routers have been assigned an IP address, subnet mask, and default gateway. The routers are running RIP and the networks directly connected to the first router do not pass to the second router. However, a ping from one router to the serial interface of the directly connected neighboring router is successful.D、A router connects to another router via a switch. Both routers and the switch have been assigned an IP address, subnet mask, and default gateway. Neither the routers nor the switch are able to ping one of the hosts that is directly to the switch.
You have been asked to configure your MX240 with a default route toward your upstream ISP atIP address 192.168.100.1. Which command successfully completes this task?（）A、user@router# set routing-options static route 0.0.0.0/0 next-hop 192.168.100.1B、user@router# set routing-options default route 0.0.0.0/0 next-hop 192.168.100.1C、user@router# set forwarding-options static route 0.0.0.0/0 next-hop 192.168.100.1D、user@router# set protocols default route 0.0.0.0/0 next-hop 192.168.100.1
Refer to the exibit. Three cisco 2950 switches are set to their default priority sttings.During the spanningtree process,which switch will be elected as the root bridge?（）A、Switch3B、Switch4C、Switch2D、Switch1
You are a systems administrator and you are about to assign static IP addresses to various servers on your network. For the network 192.168.20.24/29 the router is assigned to the first usable host address, while the last usable host address goes to your Sales server. Which one of the following commands would you enter into the IP properties box of the sales server?（）A、IP address: 192.168.20.14 Subnet Mask: 255.255.255.248 Default Gateway:192.168.20.9B、IP address: 192.168.20.254 Subnet Mask: 255.255.255.0 Default Gateway:192.168.20.1C、IP address: 192.168.20.30 Subnet Mask 255.255.255.248 Default Gateway:192.168.20.25D、IP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.17E、IP address: 192.168.20.30 Subnet Mask 255.255.255.240 Default Gateway:192.168.20.25
You replaced your Layer 3 switch， which is the default gateway of the end users. Many users cannot access anything now， including email， Internet， and other applications， although other users do not have any issues. All of the applications are hosted in an outsourced data center. In order to fix the problem， which one of these actions should you take？（）A、Clear the MAC address table in the switch.B、Clear the ARP cache in the switch.C、Clear the ARP cache in the end devices.D、Clear the ARP cache in the application servers.
When is a first-hop redundancy protocol needed in the distribution layer?（）A、when HSRP is not supported by the designB、when multiple vendor devices need to be supportedC、when preempt tuning of the default gateway is neededD、when a robust method of backing up the default gateway is neededE、when the design implements Layer 2 between the access switch and the distribution switchF、when the design implements Layer 3 between the access switch and the distribution switch
An administrator is testing setting the IP address on a Linux server from command line. Which of the following commands is used to set the default gateway for the server？（）A、routeB、tracerouteC、ipconfigD、nmap
A system has a critical need for network services on a small network with a limited number of hosts. System overhead is not a concern. Which of the following should the system administrator do to help ensure connectivity in the event of a gateway failure？（）A、Use the ifconfig command to enable dead gate detectionB、Use the no command to set active dead gateway detectionC、Use the route command to set active dead gateway detectionD、Add the line active_dgd=1 to the /etc/gated.conf command and refresh the gated daemon
Which script is executed during system startup to set the system hostname， default gateway and static routes？（）A、/etc/rpcB、/etc/rc.netC、/etc/rc.tcpipD、/etc/resolv.conf
How can you reset your router or switch to factory defaults?（）A、reset configurationB、load factory-defaultC、load override defaultD、set default configuration
Your network contains a computer named Computer1. Computer1 is assigned an IP address of 39 / 84 192.168.1.112/26.Your companys corporate policy states that the first usable address in each subnet is allocated to the default gateway.You need to configure the default gateway for Computer1.Which address should you choose？（）A、192.168.1.1B、192.168.1.63C、192.168.1.65D、192.168.1.93
Your network contains a server named Server1. Server1 runs Windows Server 2008 R2 and has a single network connection. The connection is configured to use a default gateway address of 10.0.0.1.The default gateway has a metric value of 100.You configure a second default gateway that uses an address of 10.0.0.2.You need to ensure that 10.0.0.2 is only used as the default gateway if 10.0.0.1 is unreachable. What should you do？（）A、For the interface, set the interface metric to 100.B、For the 10.0.0.2 gateway, set the metric to 50.C、For the 10.0.0.2 gateway, set the metric to 200.D、For the 10.0.0.1 gateway and the 10.0.0.2 gateway, enable automatic metric.
Your wireless network is not listed in the Connect to a network window of your computer. You need to connect to your wireless network. Which two actions should you perform？（）A、Right-click and click the Diagnose option in the Connect to a network window.B、Set the security type value to No authentication in the wireless network properties dialog box.C、Click the Manually connect to a wireless network option in the Set up a connection or network window.D、In the Wireless Network properties dialog box， click the Connect even if the network is not broadcasting option.E、Configure the correct IP address， subnet mask， and default gateway for the target network in the wireless network connection properties dialog box.
Your network consists of a single Active Directory domain named nwtraders.com. All network servers run Windows Server 2003 Service Pack 2 (SP2).The relevant IP configuration for the network is configured as shown in the following table. DC1 contains an Active Directory-integrated zone for nwtraders.com.From Server2, you run the Ping 172.26.26.11 command and receive a request timed out error message. From Server2, you run the Ping 172.16.16.129 command and receive a reply. You need to ensure that you can join Server2 to the nwtraders.com domain. What should you do?（） A、Set the IP address to 172.16.16.2.B、Set the subnet mask to 255.255.255.128.C、Set the default gateway address to 172.16.16.129.D、Set the preferred DNS server address to 172.16.16.130.
单选题Which script is executed during system startup to set the system hostname， default gateway and static routes？（）A/etc/rpcB/etc/rc.netC/etc/rc.tcpipD/etc/resolv.conf
单选题You need to set the default gateway of one of your TestKing switches. Which command will set the default gateway to 192.168.12.1 on a Cisco switch?（）ASwitch(config)# ip default-network 192.168.12.1BSwitch(config)#ip route-default 192.168.12.1CSwitch(config)# ip default-gateway 192.168.12.1DSwicth(config)# ip route 192.168.12.1 0.0.0.0
单选题When is a first-hop redundancy protocol needed in the distribution layer?（）Awhen HSRP is not supported by the designBwhen multiple vendor devices need to be supportedCwhen preempt tuning of the default gateway is neededDwhen a robust method of backing up the default gateway is neededEwhen the design implements Layer 2 between the access switch and the distribution switchFwhen the design implements Layer 3 between the access switch and the distribution switch
单选题As a TestKing trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?（）ATestKSwitch(config)# ip route-default 192.168.1.115BTestKSwitch(config)# ip default-gateway 192.168.1.115CTestKSwitch(config)# ip route 192.168.1.115 0.0.0.0DTestKSwitch(config)# ip default-network 192.168.1.115
单选题You have been asked to configure your MX240 with a default route toward your upstream ISP atIP address 192.168.100.1. Which command successfully completes this task?（）Auser@router# set routing-options static route 0.0.0.0/0 next-hop 192.168.100.1Buser@router# set routing-options default route 0.0.0.0/0 next-hop 192.168.100.1Cuser@router# set forwarding-options static route 0.0.0.0/0 next-hop 192.168.100.1Duser@router# set protocols default route 0.0.0.0/0 next-hop 192.168.100.1
单选题Your companys security policy requires complex passwords. You have a comma delimited file named import.csv that contains user account information. You need to create user accounts in the domain by using the import.csv file. You also need to ensure that the new user accounts are set to use default passwords and are disabled. What should you do（）AModify the userAccountControl attribute to disabled. Run the csvde i k f import.csv command. Run the DSMOD utility to set default passwords for the user accounts.BModify the userAccountControl attribute to accounts disabled. Run the csvde f import.csv command. Run the DSMOD utility to set default passwords for the user accounts.CModify the userAccountControl attribute to disabled. Run the wscript import.csv command. Run the DSADD utility to set default passwords for the imported user accounts.DModify the userAccountControl attribute to disabled. Run the ldifde i f import.csv command. Run the DSADD utility to set passwords for the imported user accounts.
多选题If IP routing is enabled, which two commands set the gateway of last resort to the default gateway?（）Aip default-gateway 0.0.0.0Bip route 172.16.2.1 0.0.0.0 0.0.0.0Cip default-network 0.0.0.0Dip default-route 0.0.0.0 0.0.0.0 172.16.2.1Eip route 0.0.0.0 0.0.0.0 172.16.2.1